- 17 5月, 2011 1 次提交
-
-
由 Rafi Rubin 提交于
Signed-off-by: NRafi Rubin <rafi@seas.upenn.edu> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 10 5月, 2011 3 次提交
-
-
由 Jesper Juhl 提交于
There's a small typo in a comment in drivers/md/raid5.c - 'Of course' is misspelled as 'Ofcourse'. This patch fixes the spelling error. Signed-off-by: NJesper Juhl <jj@chaosbits.net> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
由 Justin P. Mattock 提交于
- kenrel -> kernel - whetehr -> whether - ttt -> tt - sss -> ss Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
由 Wanlong Gao 提交于
change the "mc13783_regulator_probe" string in the function "mc13783_regulator_probe" to "__func__" for the debug statement be consistent with the style of the rest of the file. Signed-off-by: NWanlong Gao <wanlong.gao@gmail.com> Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 27 4月, 2011 1 次提交
-
-
由 Jiri Kosina 提交于
This is a partial revert of 6eab04a8 ("treewide: remove extra semicolons"). Wireless tree removes the code in question in rtlwifi driver, so drop the hunk to avoid conflict. Reported-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 26 4月, 2011 1 次提交
-
-
由 Joe Perches 提交于
Using C line continuation inside format strings is error prone. Clean up the unintended whitespace introduced by misuse of \. Neaten correctly used line continations as well for consistency. drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well, but arcmsr needs a lot more work and the driver should likely be moved to staging instead. Signed-off-by: NJoe Perches <joe@perches.com> Acked-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 24 4月, 2011 9 次提交
-
-
由 Jian Peng 提交于
At the end of section 10.1 of AHCI spec (rev 1.3), it states Software shall not set PxCMD.ST to 1 until it is determined that a functoinal device is present on the port as determined by PxTFD.STS.BSY=0, PxTFD.STS.DRQ=0 and PxSSTS.DET=3h Even though most AHCI host controller works without this check, specific controller will fail under this condition. Signed-off-by: NJian Peng <jipeng2005@gmail.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Igor Plyatov 提交于
The "struct ata_timing" must contain 10 members, but ".dmack_hold" member was forgotten for "initial_timing" initialisation. This patch fixes such a problem. Signed-off-by: NIgor Plyatov <plyatov@gmail.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Igor Plyatov 提交于
The AT91SAM9 microcontrollers with master clock higher then 105 MHz and PIO0, have overflow of the NCS_RD_PULSE value in the MSB. This lead to "NCS_RD_PULSE" pulse longer then "NRD_CYCLE" pulse and driver does not detect ATA device. Signed-off-by: NIgor Plyatov <plyatov@gmail.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Seth Heasley 提交于
The previously submitted patch was word-wrapped. This patch adds the AHCI-mode SATA DeviceIDs for the Intel Panther Point PCH. Signed-off-by: NSeth Heasley <seth.heasley@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Seth Heasley 提交于
The previously submitted patch was word-wrapped. This patch adds the IDE-mode SATA DeviceIDs for the Intel Panther Point PCH. Signed-off-by: NSeth Heasley <seth.heasley@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Mahoney 提交于
Commit 4a5610a0 fixed an issue with the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user reported a similar issue with his DVR-216D that the NOSETXFER horkage worked around for him as well. This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER. The issue was reported at: https://bugzilla.novell.com/show_bug.cgi?id=679143Reported-by: NVolodymyr Kyrychenko <vladimir.kirichenko@gmail.com> Signed-off-by: NJeff Mahoney <jeffm@suse.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Maxime Bizon 提交于
The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they are also called during port initialization, before ahci host irq handler is registered. On ce4100 platform, this sometimes triggers "irq 4: nobody cared" message when loading driver. Fixed this by not touching the register if the port is in frozen state, and mark all uninitialized port as frozen. Signed-off-by: NMaxime Bizon <mbizon@freebox.fr> Acked-by: NTejun Heo <tj@kernel.org> Cc: stable@kernel.org Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Tejun Heo 提交于
NVIDIA mcp65 familiy of controllers cause command timeouts when DIPM is used. Implement ATA_FLAG_NO_DIPM and apply it. This problem was reported by Stefan Bader in the following thread. http://thread.gmane.org/gmane.linux.ide/48841 stable: applicable to 2.6.37 and 38. Signed-off-by: NTejun Heo <tj@kernel.org> Reported-by: NStefan Bader <stefan.bader@canonical.com> Cc: stable@kernel.org Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Hannes Reinecke 提交于
This patch adds an sysfs attribute 'em_message_supported' to the ahci host device which prints out the supported enclosure management message types. Signed-off-by: NHannes Reinecke <hare@suse.de> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 22 4月, 2011 2 次提交
-
-
由 Tejun Heo 提交于
check_events() implementations in both ide-gd and ide-cd are inadequate for in-kernel event polling. Both generate media change events continuously when certain conditions are met causing infinite event loop between the driver and userland event handler. As disk event now supports suppression of unlisted events, simply de-listing DISK_EVENT_MEDIA_CHANGE from disk->events resolves the problem. Internal handling around media revalidation will behave the same while userland will fall back to userland event polling after detecting the device doesn't support disk events. Signed-off-by: NTejun Heo <tj@kernel.org> Reported-by: NJens Axboe <jaxboe@fusionio.com> Acked-by: N"David S. Miller" <davem@davemloft.net> Signed-off-by: NJens Axboe <jaxboe@fusionio.com>
-
由 Randy Dunlap 提交于
Change <sectors> from unsigned long long to sector_t. This matches its source field. ERROR: "__udivdi3" [drivers/md/raid456.ko] undefined! Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 21 4月, 2011 7 次提交
-
-
由 Amit Shah 提交于
This call was disabled as hot-unplugging one virtconsole port led to another virtconsole port freezing. Upon testing it again, this now works, so enable it. In addition, a bug was found in qemu wherein removing a port of one type caused the guest output from another port to stop working. I doubt it was just this bug that caused it (since disabling the hvc_remove() call did allow other ports to continue working), but since it's all solved now, we're fine with hot-unplugging of virtconsole ports. Signed-off-by: NAmit Shah <amit.shah@redhat.com> Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
-
由 Amit Shah 提交于
In the case where a virtio-console port is in use (opened by a program) and a virtio-console device is removed, the port is kept around but all the virtio-related state is assumed to be gone. When the port is finally released (close() called), we call device_destroy() on the port's device. This results in the parent device's structures to be freed as well. This includes the PCI regions for the virtio-console PCI device. Once this is done, however, virtio_pci_release_dev() kicks in, as the last ref to the virtio device is now gone, and attempts to do pci_iounmap(pci_dev, vp_dev->ioaddr); pci_release_regions(pci_dev); pci_disable_device(pci_dev); which results in a double-free warning. Move the code that releases regions, etc., to the virtio_pci_remove() function, and all that's now left in release_dev is the final freeing of the vp_dev. Signed-off-by: NAmit Shah <amit.shah@redhat.com> Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
-
由 Amit Shah 提交于
When detaching a buffer from a vq, the avail.idx value should be decremented as well. This was noticed by hot-unplugging a virtio console port and then plugging in a new one on the same number (re-using the vqs which were just 'disowned'). qemu reported 'Guest moved used index from 0 to 256' when any IO was attempted on the new port. CC: stable@kernel.org Reported-by: Njuzhang <juzhang@redhat.com> Signed-off-by: NAmit Shah <amit.shah@redhat.com> Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
-
由 Joseph Cihula 提交于
Intel VT-d Protected Memory Regions (PMRs) are supposed to be disabled, on each VT-d engine, after DMA remapping is enabled on the engines. This is because the behavior of having both enabled is not deterministic and because, if TXT has been used to launch the kernel, the PMRs may be programmed to cover memory regions that will be used for DMA. Under some circumstances (certain quirks detected, lack of multiple devices, etc.), the current code does not set up DMA remapping on some VT-d engines. In such cases it also skips disabling the PMRs. This causes failures when the kernel is launched with TXT (most often this occurs on the graphics engine and results in colored vertical bars on the display). This patch detects when the kernel has been launched with TXT and then disables the PMRs on all VT-d engines. In some cases where the reason that remapping is not being enabled is due to possible ACPI DMAR table errors, the VT-d engine addresses may not be correct and thus not able to be safely programmed even to disable PMRs. Because part of the TXT launch process is the verification of these addresses, it will always be safe to disable PMRs if the TXT launch has succeeded and hence only doing this in such cases. Signed-off-by: NJoseph Cihula <joseph.cihula@intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Vasiliy Kulikov 提交于
pg_start is copied from userspace on AGPIOC_BIND and AGPIOC_UNBIND ioctl cmds of agp_ioctl() and passed to agpioc_bind_wrap(). As said in the comment, (pg_start + mem->page_count) may wrap in case of AGPIOC_BIND, and it is not checked at all in case of AGPIOC_UNBIND. As a result, user with sufficient privileges (usually "video" group) may generate either local DoS or privilege escalation. Signed-off-by: NVasiliy Kulikov <segoon@openwall.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Vasiliy Kulikov 提交于
page_count is copied from userspace. agp_allocate_memory() tries to check whether this number is too big, but doesn't take into account the wrap case. Also agp_create_user_memory() doesn't check whether alloc_size is calculated from num_agp_pages variable without overflow. This may lead to allocation of too small buffer with following buffer overflow. Another problem in agp code is not addressed in the patch - kernel memory exhaustion (AGPIOC_RESERVE and AGPIOC_ALLOCATE ioctls). It is not checked whether requested pid is a pid of the caller (no check in agpioc_reserve_wrap()). Each allocation is limited to 16KB, though, there is no per-process limit. This might lead to OOM situation, which is not even solved in case of the caller death by OOM killer - the memory is allocated for another (faked) process. Signed-off-by: NVasiliy Kulikov <segoon@openwall.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Linus Walleij 提交于
The rtc_device_register() call has changed semantics so that it will immediately call out to rtc_read_alarm() and since the callbacks require the drvdata to be set, we need to set it before the registration call to avoid NULL dereference. Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
-
- 20 4月, 2011 16 次提交
-
-
由 Krzysztof Wojcik 提交于
Problem: After raid4->raid0 takeover operation, another takeover operation (e.g raid0->raid10) results "kernel oops". Root cause: Variables 'degraded' in mddev structure is not cleared on raid45->raid0 takeover. This patch reset this variable. Signed-off-by: NKrzysztof Wojcik <krzysztof.wojcik@intel.com> Signed-off-by: NNeilBrown <neilb@suse.de>
-
由 NeilBrown 提交于
A raid0 array doesn't set 'dev_sectors' as each device might contribute a different number of sectors. So when converting to a RAID4 or RAID5 we need to set dev_sectors as they need the number. We have already verified that in fact all devices do contribute the same number of sectors, so use that number. Signed-off-by: NNeilBrown <neilb@suse.de>
-
由 NeilBrown 提交于
We previously needed to set ->queue_lock to match the raid5 device_lock so we could safely use queue_flag_* operations (e.g. for plugging). which test the ->queue_lock is in fact locked. However that need has completely gone away and is unlikely to come back to remove this now-pointless setting. Signed-off-by: NNeilBrown <neilb@suse.de>
-
由 Cédric Cano 提交于
agd5f: fix commit message. Signed-off-by: NCedric Cano <ccano@interfaceconcept.com> Reviewed-by: NMichel Dänzer <michel@daenzer.net> Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Prefer min m to max p only on pre-r7xx asics. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=36197Signed-off-by: NAlex Deucher <alexdeucher@gmail.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Mikhail Kshevetskiy 提交于
Problem description: gsm_queue() calculate a CRC for arrived frames. As a last step of CRC calculation it call gsm->fcs = gsm_fcs_add(gsm->fcs, gsm->received_fcs); This work perfectly for the case of GSM0 mode as gsm->received_fcs contain the last piece of data required to generate final CRC. gsm->received_fcs is not used for GSM1 mode. Thus we put an additional byte to CRC calculation. As result we get a wrong CRC and reject incoming frame. Signed-off-by: NMikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com> Acked-by: NAlan Cox <alan@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Uwe Kleine-König 提交于
If cts changes between reading the level at the cts input (USR1_RTSS) and acking the irq (USR1_RTSD) the last edge doesn't generate an irq and uart_handle_cts_change is called with a outdated value for cts. The race was introduced by commit ceca629e ([ARM] 2971/1: i.MX uart handle rts irq) Reported-by: NArwed Springer <Arwed.Springer@de.trumpf.com> Tested-by: NArwed Springer <Arwed.Springer@de.trumpf.com> Cc: stable@kernel.org # 2.6.14+ Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Niels de Vos 提交于
Replace release_resource() by release_region() and also fix the inconsistency in the size of the requested/released region. The size of the resource should be 32, not 0x8 like it was corrected in commit e7c310c3 already. CC: linux-serial@vger.kernel.org Reported-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NNiels de Vos <ndevos@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Marcin Slusarz 提交于
Commit 73412c38 ("drm/nouveau: allocate kernel's notifier object at end of block") intended to align end of notifier block to page boundary, but start of block was miscalculated to be off by -16 bytes. Fix it. Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com> Cc: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Marcin Slusarz 提交于
nouveau_bo_wr32 expects offset to be in words, but we pass value in bytes, so after commit 73412c38 ("drm/nouveau: allocate kernel's notifier object at end of block") we started to overwrite some memory after notifier buffer object (previously m2mf_ntfy was always 0, so it didn't matter it was a value in bytes). Reported-by: NDominik Brodowski <linux@dominikbrodowski.net> Reported-by: NNigel Cunningham <lkml@nigelcunningham.com.au> Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Pekka Paalanen <pq@iki.fi> Cc: stable@kernel.org [2.6.38] Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Problem introduced with commit 6ba9a683Reported-by: NBob Gleitsmann <rjgleits@bellsouth.net> Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Caught with kmemcheck on unrelated business. Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Wasn't aware they even existed, apparently they do! They're actually AGP chips with a bridge as far as I can tell, which puts them in the same boat as nv40/nv45. Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
-
由 Ben Skeggs 提交于
Fixes a possible lock ordering reversal between context_switch_lock and ramin_lock. Signed-off-by: NBen Skeggs <bskeggs@redhat.com> Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
-
由 Rafael J. Wysocki 提交于
Device suspend/resume infrastructure is used not only by the suspend and hibernate code in kernel/power, but also by APM, Xen and the kexec jump feature. However, commit 40dc166c (PM / Core: Introduce struct syscore_ops for core subsystems PM) failed to add syscore_suspend() and syscore_resume() calls to that code, which generally leads to breakage when the features in question are used. To fix this problem, add the missing syscore_suspend() and syscore_resume() calls to arch/x86/kernel/apm_32.c, kernel/kexec.c and drivers/xen/manage.c. Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Acked-by: NIan Campbell <ian.campbell@citrix.com>
-
由 Linus Torvalds 提交于
This reverts commit 35d9f510. Quoth Jiri Slaby: "It fixes mmap when IOMMU is used on x86 only, but breaks architectures like ARM or PPC where virt_to_phys(dma_alloc_coherent) doesn't work. We need there dma_mmap_coherent or similar (the trickery what snd_pcm_default_mmap does but in some saner way). But this cannot be done at this phase." Requested-by: NJiri Slaby <jslaby@suse.cz> Cc: Russell King - ARM Linux <linux@arm.linux.org.uk> Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-