When there is more than one VIF, listen for all beacons
and ensure ATH9K_RX_FILTER_MCAST_BCAST_ALL is set.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use key management functions which have been moved to ath/key.c and remove
ath9k copies of these functions and other now unused definitions.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace ah_aes_support and ah_combined_mic with common ath_crypt_caps
ATH_CRYPT_CAP_CIPHER_AESCCM and ATH_CRYPT_CAP_MIC_COMBINED.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace common->splitmic with ATH_CRYPT_CAP_MIC_COMBINED flag.

splitmic has to be used when the ATH_CRYPT_CAP_MIC_COMBINED capability flag is
not set.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the old ath5k key handling functions, since we now use the key
management in ath common.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use common ath key management functions in ath5k. This fixes problems with HW
encryption in AP mode, which was broken in the ath5k implementation.

Before (with the ath5k implementation) only one client could connect to the AP
using HW encryption and WPA. When a second client connected, the first client
was not able to send/receive any more packets. Because of the problems with HW
encryption, software encryption was always used in AP mode, which resulted in a
high CPU load (and/or low thruput) on embedded devices. Instead of trying to
fix the implementation in ath5k it makes more sense to share the code with
ath9k.

This also enables HW encryption for AP mode again.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Copied the key cache management functions from ath9k (common.c and hw.c) to
ath/key.c so we can use them from ath5k, later.

Minor changes have been made:
 - renamed ath9k_* to ath_*
 - replaced ah->caps.keycache_size with common->keymax
 - removed ATH9K_IS_MIC_ENABLED since it is always true.
 - the AR_PCU_MIC_NEW_LOC_ENA flag is replaced with (splitmic == 0).
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used later in this patch series.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The output becomes:

[   41.261941] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These were introduced in "wl1271: sdio: claim host only when doing IO"

drivers/net/wireless/wl12xx/wl1271_sdio.c: In function ‘wl1271_sdio_set_power’:
drivers/net/wireless/wl12xx/wl1271_sdio.c:193: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:195: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:186: warning: unused variable ‘func’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sta_info_get_bss() is used to match STA pointers
for VLAN/AP interfaces, but if the same station
is also added to multiple other interfaces it
will erroneously match because both pointers are
NULL, fix this by ignoring NULL pointers here.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If AR_KeyMiss is set in the rx descriptor and AR_RxFrameOK is unset,
the hardware could not locate a valid key during a decryption attempt.

In this case, the frame must not be reported as decrypted, otherwise
mac80211 sees only random garbage.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

At the time the .add_interface driver op is called, the interface has not
been marked as running yet, so ieee80211_iterate_active_interfaces will
not pass it to the iterator function.
Because of this, the calculated BSSID mask is wrong, which breaks multi-BSS
operation.

Additionally, the current way of comparing all addresses against each other
is pointless, as the hardware only uses the hardware MAC address and the BSSID
mask for matching the destination address, so all the address array
reallocation is completely unnecessary.

This patch simplifies the logic by setting the initial mask bytes to 0xff
and removing all bits in the iterator call that don't match the hardware MAC
address. It also calls the iterator for the vif that was passed to
add_interface()
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The CPU consumption during the scan period is high, since
the register write go over Interrupt endpoint. On downloading
the firmware to the target, the USB descriptors are
'patched' to change the type of the endpoints from Interrupt
to Bulk.

With this fix, the CPU usage during a scan run comes down to
acceptable levels.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_wmi_ctrl_rx is racy with ath9k_wmi_tasklet on event notification
due to which the wmi_skb may be overwritten which leads to memory leak.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Even is someone else complete scanning in mac80211, apply rxon and
tx power settings if gets scan complete notification from hardware.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace IWL_DEBUG_{INFO,HC,RC} to IWL_DEBUG_SCAN in iwl-scan.c file. Add
some more IWL_DEBUG_SCAN messages. This will allow to fully debug
scanning using only IWL_DL_SCAN flag.

Also start one message sentence with capital letter, since that
convention in iwl-scan.c file.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove redundant checks and use iwl_is_ready_rf().
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is needed to avoid warning in ieee80211_restart_hw about hardware
scan in progress.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently we force scan complete at the end of iwl_scan_cancel_timeout
function. This cause race condition when we can get a new scan request
from mac80211 and complete it by iwl_bg_complete from older scan. Change
code to force scan complete only when really needed: device goes down,
interface is removed or scan timeout occurs.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assure we complete scan in mac80211 when we abort scanning (scan_abort
work) or scan timeout occurs (scan_check work). Currently
iwl_scan_cancel_timeout() procedure force scan finish in mac80211
at the end of timeout loop, so we can use it in proper work functions.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we do not get notification from hardware about scan complete, after
timeout do mac80211 scan completion anyway. This assure we end scan
in case of firmware hung.

Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assure (partially) we call ieee80211_scan_completed() only once when
scan was requested from mac80211.

Code path that first clear STATUS_SCANNING bit is responsible to call
ieee80211_scan_completed(). Before the call, we check if mac80211
really request the scan.

Still persist some cases when we behave wrong, that will be addressed
in the next patches.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since on timeout version of iwl_scan_cancel procedure we can sleep,
do not have to schedule abort_scan work to begin and perform scanning,
can do this directly. Also now, as we do not queue abort_scan from
restart work anymore, we can queue abort_scan to priv->workqueue.

Don't drop mutex when waiting for scan complete. Use STATUS_HW_SCAN bit
to check if scanning is currently pending, because STATUS_SCANNING will
be cleared only with priv->mutex taken.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we are not able to send abort command to firmware, notify mac80211
that we complete scan, as we will newer do it lately. Check for all
possible errors that low level sending command procedure does not check,
to assure we catch all failures cases.

Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Always cancel scan when stooping device and scan is currently pending,
we should newer have scan running after down device.

To assure we start scan cancel from restart work we have to schedule
abort_scan to different workqueue than priv->workqueue.

Patch fix not cancel scanning when restarting firmware, what is
one of the causes of wdev_cleanup_work warning (together with permanent
network connection lost) reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the scan completed flags handling so that we
can notify mac80211 about aborted scans with the
correct status. Also queue the scan_completed work
before the BT status update so that it won't see
the bits still set (unless a new scan was started
in which case that's fine.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rather than duplicating all the checks and even
in case of errors accepting the scan request
from mac80211, we can push the checks to the
caller and in all error cases reject the scan
request right away (rather than accepting and
then saying it was aborted).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a number of conf variables that are
unused, remove them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hdr pointer is left dangling after call to ieee80211_skb_resize. This
can cause guards around mesh path selection to fail.
Signed-off-by: NSteve deRosier <steve@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a path in nl80211_set_wiphy where result is tested but
uninitialized.

I am hitting this path when I attempt:

sh# iw dev wlan0 set channel 10
command failed: Unknown error 1069727332 (-1069727332)
Signed-off-by: NWilliam Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace sizeof(rtap_namespace_sizes) / sizeof(rtap_namespace_sizes[0])
with ARRAY_SIZE(rtap_namespace_sizes) in net/wireless/radiotap.c
Signed-off-by: NNikitas Angelinas <nikitasangelinas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace (sizeof(ofdm_level_table)/sizeof(ofdm_level_table[0]) with
ARRAY_SIZE(ofdm_level_table), and (sizeof(cck_level_table)/
sizeof(cck_level_table[0]) with ARRAY_SIZE(cck_level_table) in
drivers/net/wireless/ath/ath9k/ani.c
Signed-off-by: NNikitas Angelinas <nikitasangelinas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't generate calibration errors messages when not needed.
Signed-off-by: NFabio Rossi <rossi.f@inwind.it>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a typo introduced in "rt2x00: Add helper function for reporting tx
status" that results in an oops in rt2x00lib_txdone.
Reported-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We're handling both, the CSR_BEACON_DONE and the CSR_TWAKEUP interrupts
in rt61pci. However, these interrupts are masked out by default. Fix
this.

Found via pure code inspection.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't use all available interrupts in rt2800pci. Mask out all unused
interrupts to avoid waking up without having anything to do.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously rt2x00 was always updating all erp related config variables
even though mac80211 might only have changed one. Hence, pass the
changed flags to the config_erp driver callback so that the driver
can limit the changes to the correct values.

This fixes an issue in AP mode where the beacon interval is not
initialized (and thus zero) but still sent to the hardware causing an
interrupt storm on rt2800pci hanging the system.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>