By default normal mode is chosen when driver is loaded. This
patch adds a provision to choose manufacturing mode via module
parameters.

Below command loads driver in manufacturing mode
insmod mwifiex.ko mfg_mode=1.
Tested-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

While fixing another bug, I noticed that bcma manually sets up
a dma_mask pointer for its child devices. We have a generic
helper for that now, which should be able to cope better with
any variations that might be needed to deal with cache coherency,
unusual DMA address offsets, iommus, or limited DMA masks, none
of which are currently handled here.

This changes the core to use the of_dma_configure(), like
we do for platform devices that are probed directly from
DT.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

%ul was likely meant as %lu to print an unsigned long,
not an unsigned with a letter l at the end.
But in fact the value printed is u32 anyway, so just drop
the l completely.
Signed-off-by: NOleg Drokin <green@linuxhacker.ru>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Printing about 3000 lines like this

[   20.691850] mwifiex_pcie 0000:02:00.0: .
[   20.693466] mwifiex_pcie 0000:02:00.0: .

is not useful. If FW downloading will be interrupted, we will get
proper error message about that.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For debugging purpose print content of reg->fw_status register and other
variables values when waiting for firmware ready event.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Printing ret and adapter->winner do not provide any useful information
as those are always 0 at point where the massage is printed. Print value
read from reg->fw_status register instead.

Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add time sync configuration api.
The new api allows to configure the synchronization
mode (STA/AP/MESH) and (in case of Mesh mode) the
master address of each zone.
Signed-off-by: NGuy Mishol <guym@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The struct cfg80211_pmksa defines its bssid field as:

    const u8 *bssid;

contrary to struct brcmf_pmksa, which uses:

    u8 bssid[ETH_ALEN];

Therefore in brcmf_cfg80211_del_pmksa(), &pmksa->bssid takes the address
of this field (of type u8**), not the one of its content (which would be
u8*).  Remove the & operator to make brcmf_dbg("%pM") and memcmp()
behave as expected.

This bug have been found using a custom static checker (which checks the
usage of %p... attributes at build time).  It has been introduced in
commit 6c404f34 ("brcmfmac: Cleanup pmksa cache handling code"),
which replaced pmksa->bssid by &pmksa->bssid while refactoring the code,
without modifying struct cfg80211_pmksa definition.

Replace &pmk[i].bssid with pmk[i].bssid too to make the code clearer,
this change does not affect the semantic.

Fixes: 6c404f34 ("brcmfmac: Cleanup pmksa cache handling code")
Cc: stable@vger.kernel.org
Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The AE1200 comes with different revisions of the BCM43235 chipset,
but all have the same USB ID. Only revision 3 can be supported.
Signed-off-by: NIsmael Luceno <ismael@iodev.co.uk>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some RTL8821AE devices sold in Great Britain have the country code of
0x25 encoded in their EEPROM. This value is not tested in the routine
that establishes the regulatory info for the chip. The fix is to set
this code to have the same capabilities as the EU countries. In addition,
the channels allowed for COUNTRY_CODE_ETSI were more properly suited
for China and Israel, not the EU. This problem has also been fixed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Trivial fix to spelling mistake in dev_err message.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On my home network rtl8xxxu is spamming the log with
IEEE80211_AMPDU_RX_START / IEEE80211_AMPDU_RX_STOP every few seconds
turn these messages into debug messages.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
[kvalo@codeaurora.org: fix commit title]
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixes the following sparse warning:

drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:898:1: warning:
 symbol 'rtl8xxxu_gen1_h2c_cmd' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Split the filling of TX descriptors into a generic portion used on all
devices, and format specific helper functions provided in the fops
structure.

This also cleaned up some mess, even if non harmful, in the handling
of txdesc40 descriptors, where the code randomly would switch between
the pointer to tx_desc and tx_desc40.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Another patch to move this detection out of the code handling the TX
descriptor update.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In order to be able to split out the TX descriptor handling code,
determine in advance the need to mark SGI.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Calculating the value in one place rather than using one calculation
in one place and a different one for management frames in another
location makes little sense.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Do not rely on TX descriptor size to determine the thermal meter
type.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This leaves space for a few more flags within the same space.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use a fileops flag to indicate whether the device has TX report timer
support. This will make it easier to include future devices such as
8188eu to use the TX report timer.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These are primarily needed for SDIO/PCI parts, but the vendor driver
still sets them for some USB devices.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This adds TX antenna selection bit defines for OFDM mode.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With all devices now offering fops->total_page_num, get rid of the
if mess for setting the TX buffer boundary.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Switching over the old devices to use the new function allows us to
get rid of this legacy.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This was the last user of the old
rtl8xxxu_old_init_queue_reserved_page() which can now be removed.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This changes the pub-queue value written to REQ_RQPN, however the old
code used a hard coded minimum value assuming there would always be an
active lo-queue, even when no USB EP was found for it.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This switches the 8723b driver to use the new
rtl8xxxu_init_queue_reserved_page() function.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is an rtl8192eu based dongle (the v1 is an rtl8192cu). Reported
and tested by Myckel Habets.
Reported-by: NMyckel Habets <myckel@sdf.lonestar.org>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For some reason we lost the code bailing if rtl8xxxu_init_device()
returned an error.

This catches the error and also cleans up the error handling.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

D-Link DWA-121 is reported as working.
Reported-by: NStefano Bravi <stefanobravi69@libero.it>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Successfully tested by Jocelyn Mayer
Reported-by: NJ. Mayer <l_indien@magic.fr>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This field was added to wl_sta struct to get hw in situations
where it was not given to driver by mac80211. In our case,
get_expected_throughput op did not send hw to driver.

This patch reverts the change, as it is no longer needed due to commit
4fdbc67a ("mac80211: call get_expected_throughput only after adding
station") as hw is now sent as a parameter.
Signed-off-by: NMaxim Altshul <maxim.altshul@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In case of (rtlhal->oem_id != RT_CID_DEFAULT), the function directly
returns and leaks the already allocated hwinfo memory. Go through the
correct exit path.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In case rtl_get_hwinfo() fails, the function directly returns and leaks the
already allocated hwinfo memory. Go through the correct exit path.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We get 1 warning when building kernel with W=1:

drivers/net/wireless/broadcom/brcm80211/brcmfmac/tracepoint.c:23:6: warning: no previous prototype for '__brcmf_err' [-Wmissing-prototypes]

In fact, this function is declared in brcmfmac/debug.h, so this patch
adds missing header dependencies.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The IEEE80211_STYPE_ACTION case is missing a break in the switch
statement, causing it to fall through to the default case that
reports a debug message about an unknown frame subtype. Fix this
by adding in the missing break statement.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We know that 'retval = 0' because it has been tested a few lines above.
So, if 'devm_kmalloc' fails, 0 will be returned instead of an error code.
Return -ENOMEM instead.

Fixes: 8b4c0009 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch creates custom regulatory rules based on the information
received from firmware and enable them during wiphy registration.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds command preparation and response handling for
CHAN_REGION_CFG command. These changes are prerequisites for adding
custom regulatory domain support.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AID gets updated during TDLS setup, but modified value isn't reflected
in "priv->assoc_rsp_buf". This causes TDLS setup failure. The problem is
fixed here.

Fixes: 4aff53ef ("mwifiex: parsing aid while receiving..")
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>