AM33xx uses same McASP IP as the Davinci Platform. This patch updates
Kconfig and makefile to enable build for McASP, PCM & Codec drivers.
Signed-off-by: NHebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

sffsdr machine support does not build since at least v2.6.36
(~3 years). There is little hope of it being fixed, so remove
the support.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds the support for the interface needed by the DaVinci
Voice Codec CQ93VC.
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is one instance of McASP on DA850/OMAP-L138 SoC. This is
connected to TLV320AIC3106 codec for audio playback and capture.
This patch adds audio support on this platform. Some of the
structure prefix names which are common for DA830/OMAP-L137 EVM and
DA850/OMAP-L138 EVM have been renamed to da8xx from da830.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add support for audio on DA830 EVM- here McASP1 is interfaced to
TLV320AIC3106 codec.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Adds driver support for the two instances of McASP on TI's DM646x.

The multichannel audio serial port (McASP) functions as a general-purpose audio
serial port optimized for the needs of multichannel audio application.
(http://www.ti.com/litv/pdf/spruer1b).

There are two instances of McASP on DM646x. The McASP0 module includes up to 4
serializers that can be individually enabled to either transmit or receive
in different modes. The McASP1 module is limited with only 1 pinned-out
serializer that can be enabled to only transmit in DIT mode (neither receiving
in any mode nor transmitting in either Burst or TDM mode is supported).

McASP0 consists of transmit and receive sections that may operate
synchronized, or completely independently with separate master clocks, bit
clocks, and frame syncs, and using different transmit modes with different
bit-stream formats.
Signed-off-by: NSteve Chen <schen@mvista.com>
Signed-off-by: NPavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: NNaresh Medisetty <naresh@ti.com>
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The PCM3008 is used on the Lyrtech SFFSDR board, in conjunction with an
FPGA that generates the bit clock and the master clock

[Downgraded the rate debug print to pr_debug() in hw_params, converted
asm/gpio.h to linux/gpio.h -- broonie]
Signed-off-by: NHugo Villeneuve <hugo@hugovil.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add ASoC support for the TI Davinci SoC and the Davicni-EVM reference board.
It includes:
- ASoC Davinci DMA driver
- ASoC Davinci I2S (Davinci McBSP module based) driver
- ASoC Davinci-EVM reference board
Signed-off-by: NVladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>