We're already counting remote TLB flushes in a variable, but don't export
it to user space yet. Do so, so we know what's going on.
Signed-off-by: NAlexander Graf <agraf@suse.de>

We want to have tracing information on guest exits for booke as well
as book3s. Since most information is identical, use a common trace point.
Signed-off-by: NAlexander Graf <agraf@suse.de>

Signed-off-by: NBharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Added the decrementer auto-reload support. DECAR is readable
on e500v2/e500mc and later cpus.
Signed-off-by: NBharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

When running kvm_vcpu_block and it realizes that the CPU is actually good
to run, we get a request bit set for KVM_REQ_UNHALT. Right now, there's
nothing we can do with that bit, so let's unset it right after the call
again so we don't get confused in our later checks for pending work.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When emulating updating load/store instructions (lwzu, stwu, ...) we need to
write the effective address of the load/store into a register.

Currently, we write the physical address in there, which is very wrong. So
instead let's save off where the virtual fault was on MMIO and use that
information as value to put into the register.

While at it, also move the XOP variants of the above instructions to the new
scheme of using the already known vaddr instead of calculating it themselves.
Reported-by: NJörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

So far, we've always called prepare_to_enter even when all we did was return
to the host. This patch changes that semantic to only call prepare_to_enter
when we actually want to get back into the guest.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When we get a performance monitor interrupt, we need to make sure that
the host receives it. So reinject it like we reinject the other host
destined interrupts.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When reinjecting an interrupt into the host interrupt handler after we're
back in host kernel land, we need to tell the kernel where the interrupt
happened. We can't tell it that we were in guest state, because that might
lead to random code walking host addresses. So instead, we tell it that
we came from the interrupt reinject code.

This helps getting reasonable numbers out of perf.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When during guest context we get a performance monitor interrupt, we
currently bail out and oops. Let's route it to its correct handler
instead.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The comment for program interrupts triggered when using bookehv was
misleading. Update it to mention why MSR_GS indicates that we have
to inject an interrupt into the guest again, not emulate it.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When during guest execution we get a machine check interrupt, we don't
know how to handle it yet. So let's add the error printing code back
again that we dropped accidently earlier and tell user space that something
went really wrong.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The semantics of BOOKE_IRQPRIO_MAX changed to denote the highest available
irqprio + 1, so let's reflect that in the code too.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Instead of checking whether we should reschedule only when we exited
due to an interrupt, let's always check before entering the guest back
again. This gets the target more in line with the other archs.

Also while at it, generalize the whole thing so that eventually we could
have a single kvmppc_prepare_to_enter function for all ppc targets that
does signal and reschedule checking for us.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When we fail to emulate an instruction for the guest, we better go in and
tell it that we failed to emulate it, by throwing an illegal instruction
exception.

Please beware that we basically never get around to telling the guest that
we failed thanks to the debugging code right above it. If user space however
decides that it wants to ignore the debug, we would at least do "the right
thing" afterwards.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The e500mc patches left some debug code in that we don't need. Remove it.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The CONFIG_KVM_E500 option really indicates that we're running on a V2 machine,
not on a machine of the generic E500 class. So indicate that properly and
change the config name accordingly.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When setting MSR for an e500mc guest, we implicitly always set MSR_GS
to make sure the guest is in guest state. Since we have this implicit
rule there, we don't need to explicitly pass MSR_GS to set_msr().

Remove all explicit setters of MSR_GS.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When one vcpu wants to kick another, it can issue a special IPI instruction
called msgsnd. This patch emulates this instruction, its clearing counterpart
and the infrastructure required to actually trigger that interrupt inside
a guest vcpu.

With this patch, SMP guests on e500mc work.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

e500mc has a normal PPC FPU, rather than SPE which is found
on e500v1/v2.

Based on code from Liu Yu <yu.liu@freescale.com>.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Chips such as e500mc that implement category E.HV in Power ISA 2.06
provide hardware virtualization features, including a new MSR mode for
guest state.  The guest OS can perform many operations without trapping
into the hypervisor, including transitions to and from guest userspace.

Since we can use SRR1[GS] to reliably tell whether an exception came from
guest state, instead of messing around with IVPR, we use DO_KVM similarly
to book3s.

Current issues include:
 - Machine checks from guest state are not routed to the host handler.
 - The guest can cause a host oops by executing an emulated instruction
   in a page that lacks read permission.  Existing e500/4xx support has
   the same problem.

Includes work by Ashish Kalra <Ashish.Kalra@freescale.com>,
Varun Sethi <Varun.Sethi@freescale.com>, and
Liu Yu <yu.liu@freescale.com>.
Signed-off-by: NScott Wood <scottwood@freescale.com>
[agraf: remove pt_regs usage]
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

e500mc will want to do lpid allocation/deallocation here.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This gives us a place to put load/put actions that correspond to
code that is booke-specific but not specific to a particular core.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This moves the get/set_one_reg implementation down from powerpc.c into
booke.c, book3s_pr.c and book3s_hv.c.  This avoids #ifdefs in C code,
but more importantly, it fixes a bug on Book3s HV where we were
accessing beyond the end of the kvm_vcpu struct (via the to_book3s()
macro) and corrupting memory, causing random crashes and file corruption.

On Book3s HV we only accept setting the HIOR to zero, since the guest
runs in supervisor mode and its vectors are never offset from zero.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>
[agraf update to apply on top of changed ONE_REG patches]
Signed-off-by: NAvi Kivity <avi@redhat.com>

Decrementers are now properly driven by TCR/TSR, and the guest
has full read/write access to these registers.

The decrementer keeps ticking (and setting the TSR bit) regardless of
whether the interrupts are enabled with TCR.

The decrementer stops at zero, rather than going negative.

Decrementers (and FITs, once implemented) are delivered as
level-triggered interrupts -- dequeued when the TSR bit is cleared, not
on delivery.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
[scottwood@freescale.com: significant changes]
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This allows additional registers to be accessed by the guest
in PR-mode KVM without trapping.

SPRG4-7 are readable from userspace.  On booke, KVM will sync
these registers when it enters the guest, so that accesses from
guest userspace will work.  The guest kernel, OTOH, must consistently
use either the real registers or the shared area between exits.  This
also applies to the already-paravirted SPRG3.

On non-booke, it's not clear to what extent SPRG4-7 are supported
(they're not architected for book3s, but exist on at least some classic
chips).  They are copied in the get/set regs ioctls, but I do not see any
non-booke emulation.  I also do not see any syncing with real registers
(in PR-mode) including the user-readable SPRG3.  This patch should not
make that situation any worse.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

int_pending was only being lowered if a bit in pending_exceptions
was cleared during exception delivery -- but for interrupts, we clear
it during IACK/TSR emulation.  This caused paravirt for enabling
MSR[EE] to be ineffective.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This prevents us from inappropriately blocking in a KVM_SET_REGS
ioctl -- the MSR[WE] will take effect when the guest is next entered.

It also causes SRR1[WE] to be set when we enter the guest's interrupt
handler, which is what e500 hardware is documented to do.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This function should be called with interrupts disabled, to avoid
a race where an exception is delivered after we check, but the
resched kick is received before we disable interrupts (and thus doesn't
actually trigger the exit code that would recheck exceptions).

booke already does this properly in the lightweight exit case, but
not on initial entry.

For now, move the call of prepare_to_enter into subarch-specific code so
that booke can do the right thing here.  Ideally book3s would do the same
thing, but I'm having a hard time seeing where it does any interrupt
disabling of this sort (plus it has several additional call sites), so
I'm deferring the book3s fix to someone more familiar with that code.
book3s behavior should be unchanged by this patch.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This function also updates paravirt int_pending, so rename it
to be more obvious that this is a collection of checks run prior
to (re)entering a guest.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Currently we check prior to returning from a lightweight exit,
but not prior to initial entry.

book3s already does a similar test.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The hardcoded behavior prevents proper SMP support.

user space shall specify the vcpu's PIR as the vcpu id.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

There are multiple features in PowerPC KVM that can now be enabled
depending on the user's wishes. Some of the combinations don't make
sense or don't work though.

So this patch adds a way to check if the executing environment would
actually be able to run the guest properly. It also adds sanity
checks if PVR is set (should always be true given the current code
flow), if PAPR is only used with book3s_64 where it works and that
HV KVM is only used in PAPR mode.
Signed-off-by: NAlexander Graf <agraf@suse.de>

Instead of doing the kvm_guest_enter/exit() and local_irq_dis/enable()
calls in powerpc.c, this moves them down into the subarch-specific
book3s_pr.c and booke.c.  This eliminates an extra local_irq_enable()
call in book3s_pr.c, and will be needed for when we do SMT4 guest
support in the book3s hypervisor mode code.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This arranges for the top-level arch/powerpc/kvm/powerpc.c file to
pass down some of the calls it gets to the lower-level subarchitecture
specific code.  The lower-level implementations (in booke.c and book3s.c)
are no-ops.  The coming book3s_hv.c will need this.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Dynamically assign host PIDs to guest PIDs, splitting each guest PID into
multiple host (shadow) PIDs based on kernel/user and MSR[IS/DS].  Use
both PID0 and PID1 so that the shadow PIDs for the right mode can be
selected, that correspond both to guest TID = zero and guest TID = guest
PID.

This allows us to significantly reduce the frequency of needing to
invalidate the entire TLB.  When the guest mode or PID changes, we just
update the host PID0/PID1.  And since the allocation of shadow PIDs is
global, multiple guests can share the TLB without conflict.

Note that KVM does not yet support the guest setting PID1 or PID2 to
a value other than zero.  This will need to be fixed for nested KVM
to work.  Until then, we enforce the requirement for guest PID1/PID2
to stay zero by failing the emulation if the guest tries to set them
to something else.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This is a shared page used for paravirtualization.  It is always present
in the guest kernel's effective address space at the address indicated
by the hypercall that enables it.

The physical address specified by the hypercall is not used, as
e500 does not have real mode.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This is done lazily.  The SPE save will be done only if the guest has
used SPE since the last preemption or heavyweight exit.  Restore will be
done only on demand, when enabling MSR_SPE in the shadow MSR, in response
to an SPE fault or mtmsr emulation.

For SPEFSCR, Linux already switches it on context switch (non-lazily), so
the only remaining bit is to save it between qemu and the guest.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Keep the guest MSR and the guest-mode true MSR separate, rather than
modifying the guest MSR on each guest entry to produce a true MSR.

Any bits which should be modified based on guest MSR must be explicitly
propagated from vcpu->arch.shared->msr to vcpu->arch.shadow_msr in
kvmppc_set_msr().

While we're modifying the guest entry code, reorder a few instructions
to bury some load latencies.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>