There is a missing break so we use XC_RF_MODE_CABLE instead of
XC_RF_MODE_AIR.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The original xc5000c driver support was based on a beta version of the
firmware, and there were no redistribution rights.  Change over to using
the release version, for which freely redistributable firmware can be
found here:

http://kernellabs.com/firmware/xc5000/README.xc5000c
http://kernellabs.com/firmware/xc5000/dvb-fe-xc5000c-4.1.30.7.fw

Thanks to Ramon Cazares from Cresta Technology for making the firmware
available as well as working out the licensing issues.

[mchehab@redhat.com: Fix a merge conflict with the patch that added support
 for MODULE_FIRMWARE() macro]
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The driver prints out a dotted version number but it's in hex.  As a
result, the version doesn't visibly match the filename for the firmware,
and it caused a bunch of confusion while discussing different versions
with the chip manufacturer.

Change the firmware printout to be in decimal.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The xc5000c and newer versions of the xc5000a firmware need minor revisions
to their initialization process.  Add support for validating the firmware
was properly loaded, as well as checking the init status after initialization.

Based on advice from CrestaTech support as well as xc5000 datasheet v2.3.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It's possible for the xc5000 to enter an unknown state such that all
subsequent tuning requests fail.  The only way to recover is to reset the
tuner and reload the firmware.  This problem was detected after several days
straight of issuing tuning requests every five seconds.

Reset the firmware in the event that the PLL is in an unlocked state.  This
solution was provided by the engineer at CrestaTech (the company that acquired
Xceive).
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current code invokes the auto calibration of the tuner whenever the
init routine is called (whenever the DVB frontend opens the device).
However we should really only be invoking the calibration if we actually
did reset the device and reload the firmware.

Rework the routine to only do calibration if reset and firmware load was
performed.  Also because the called function is now a no-op if the
firmware is already loaded, the caller no longer needs to invoke
is_firmware_loaded().
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The logic as written would *never* actually return an error condition,
since the loop would run until the counter hit zero but the check was
for a value less than zero.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When debugging is enabled, also show the analog SNR and the total gain
status values.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The quality register only has relevant data in bits 2-0, so discard the
other bits (which results in a value being printed that is consistent
with the expected 0-7 range).
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This will make modinfo more useful with regard
to discovering necessary firmware files.

Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Michael Krufky <mkrufky@kernellabs.com>
Cc: Eddi De Pieri <eddi@depieri.net>
Cc: linux-media@vger.kernel.org
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

xc5000 is just a tuner, not a decoder, so both DMB-TH and ISDB-T should
work properly there: it is just a matter of teaching the driver what
saw filter should be used and how to calculate the center frequency.
Requested-by: NChoi Wing Chan <chanchoiwing@gmail.com>
Cc: Steven Toth <stoth@linuxtv.org>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rather than loading firmware specific for the xtal frequency, just use
the standard firmware and set the xtal frequency after firmware upload.

The modified firmware will never be released, so we're better off
merging this now rather than waiting for v3.5.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rather than loading firmware specific for the xtal frequency, just use
the standard firmware and set the xtal frequency after firmware upload.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Specify chip revision at attach time rather than a firmware image.
This is a better way to ensure that the correct firmware is loaded
for the correct revision of the chip.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

convert the firmware configuration attach-time parameter from
a pointer to an integer so as to remove the static dependency
created by the previous changesets.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

newer versions of the xc5000 silicon require newer firmware
while remaining 100% driver compatible.  original versions
of the xc5000a continue to use the same firmware.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Every frontend now uses DVBv5 way. So, let's not use the DVBv3
macros internally anymore.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is a big patch, yet trivial: now that all tuners use the DVBv5
way to pass parameters (e. g. via fe->dtv_property_cache), the
extra parameter can be removed from set_params() call.

After this change, very few DVBv3 specific stuff are left at the
tuners.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of using a roll-off factor, change DRX-K & friends to select
the bandwidth filter and the Nyquist half roll-off via delivery system.

This provides a cleaner support for Annex A/C switch.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

While xc5000 supports 7MHz bandwidth, the driver were lacking the code
implementing this feature, causing tuning issues with VHF chanels
used in Countries like Italy.

After this patch:

>>> tune to: 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
0x0000 0x0d49: pmt_pid 0x0102 RAI -- Rai 1 (running)
0x0000 0x0d4a: pmt_pid 0x0101 RAI -- Rai 2 (running)
0x0000 0x0d4b: pmt_pid 0x0100 RAI -- Rai 3 TGR Veneto (running)
0x0000 0x0d53: pmt_pid 0x0118 RAI -- Rai News (running)
0x0000 0x0d54: pmt_pid 0x0119 Rai -- Rai 3 TGR Emilia Romagna (running)
0x0000 0x0d4c: pmt_pid 0x0103 Rai -- Rai Radio1 (running)
0x0000 0x0d4d: pmt_pid 0x0104 Rai -- Rai Radio2 (running)
0x0000 0x0d4e: pmt_pid 0x0105 Rai -- Rai Radio3 (running)
Network Name 'Rai'
Tested-by: NEddi De Pieri <eddi@depieri.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

While here, add a debug message, to easy detecting bugs on it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As reported by Devin Heitmueller <dheitmueller@kernellabs.com>:

> It seems like a change such as this could significantly change the
> timing of tuner initialization if you have multiple xc5000 based
> products that might have a slow i2c bus.  Was that intentional?

After discussed with Eddi de Pierri <eddi@depieri.net>, it was pointed that
the change was not intentional, and it was just a trial while developing
the patches that add support for HVR-930C.

So, remove this hack.
Reported-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Acked by: Eddi de Pierri <eddi@depieri.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With this patch I try again to add initial support for HVR930C.

Tested only DVB-T, since in Italy Analog service is stopped.

Actually "scan -a0 -f1", find only about 50 channel while 400 should
be available.

[mchehab@redhat.com: Tested with DVB-C and fixed a few whitespace issues]
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NEddi De Pieri <eddi@depieri.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is needed for devices with DRX-K and xc5000.

Tested with a HVR 930C hardware.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Annex C support were broken with the previous implementation,
as, at xc5000 and tda18271c2dd, it were choosing the wrong bandwidth
for some symbol rates.

At DRX-J, it were always selecting Annex A, even having Annex C
support coded there.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Brazil uses 6MHz-spaced channels. So, the nyquist filter for
DVB-C should be different, otherwise, inter-channel interference
may badly affect the device, and signal may not be properly decoded.

On my tests here, without this patch, sometimes channels are seen,
but, most of the time, PID filter returns with timeout.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add one more radio input, usefull for tm6010
Add control output amplitude.
Add set_config function for configure tuner when TV card hasn't dvb part.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Making static data const avoids allocation of additional r/w memory and
reduces initialisation time.  It also provides some additional opportunities
for compiler optimisations.
Signed-off-by: NLawrence Rust <lvr@softsystem.co.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/common/tuners/xc5000.c: In function ‘xc_write_reg’:
drivers/media/common/tuners/xc5000.c:298: warning: passing argument 3 of ‘xc5000_readreg’ from incompatible pointer type
drivers/media/common/tuners/xc5000.c:235: note: expected ‘u16 *’ but argument is of type ‘u8 *’
drivers/media/common/tuners/xc5000.c: At top level:
drivers/media/common/tuners/xc5000.c:223: warning: ‘xc_read_i2c_data’ defined but not used
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rework xc_write_reg function for correct read register of the xc5000.
It is very useful for tm6000.

Tested for tm6000 and for saa7134 works well.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Xc5000 tuning attempts shouldn't return zero in the case where the firmware
did not load successfully.

Thanks to Michael Krufky for pointing out this issue.

Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove hard-coded definition of the xc5000 FM radio input, making it a
parameter passed in when doing the attach call.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add FM radio for the xc5000 silicon tuner chip.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add copyright line for xc5000.c.

Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>