Commit 9cd40029 (Fix race between
neigh_parms_release and neightbl_fill_parms) introduced device
reference counting regressions for several people, see:

	http://bugzilla.kernel.org/show_bug.cgi?id=9778

for example.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When packets are flood-forwarded to multiple output devices, the
bridge-netfilter code reuses skb->nf_bridge for each clone to store
the bridge port. When queueing packets using NFQUEUE netfilter takes
a reference to skb->nf_bridge->physoutdev, which is overwritten
when the packet is forwarded to the second port. This causes
refcount unterflows for the first device and refcount leaks for all
others. Additionally this provides incorrect data to the iptables
physdev match.

Unshare skb->nf_bridge by copying it if it is shared before assigning
the physoutdev device.

Reported, tested and based on initial patch by
Jan Christoph Nordholz <hesso@pool.math.tu-berlin.de>.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We omit (or delay) sending NSes for known-to-unreachable routers (in
NUD_FAILED state) according to RFC 4191 (Default Router Preferences
and More-Specific Routes).  But this is not fully compatible with RFC
4861 (Neighbor Discovery Protocol for IPv6), which does not remember
unreachability of neighbors.

So, let's avoid mixing sending algorithm of RFC 4191 and that of RFC
4861, and make the algorithm more friendly with RFC 4861 if RFC 4191
is disabled.

Issue was found by IPv6 Ready Logo Core Self_Test 1.5.0b2 (by TAHI
Project), and has been tracked down by Mitsuru Chinen
<mitch@linux.vnet.ibm.com>.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I noticed "ip route list" was slower than "cat /proc/net/route" on a
machine with a full Internet routing table (214392 entries : Special
thanks to Robert ;) )

This is similar to problem reported in commit
d8c92830 ("[IPV4] ROUTE: ip_rt_dump()
is unecessary slow")

Fix is to avoid scanning the begining of fz_hash table, but directly
seek to the right offset.

Before patch :

time ip route >/tmp/ROUTE

real    0m1.285s
user    0m0.712s
sys     0m0.436s

After patch

# time ip route >/tmp/ROUTE

real    0m0.835s
user    0m0.692s
sys     0m0.124s
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several of the Intel ethernet drivers keep an atomic counter used to
manage when to actually hit the hardware with a disable or an enable.

The way the net_rx_work() breakout logic works during a pending
napi_disable() is that it simply unschedules the poll even if it
still has work.

This can potentially leave interrupts disabled, but that is OK
because all of the drivers are about to disable interrupts
anyways in all such code paths that do a napi_disable().

Unfortunately, this trips up the semaphore used here in the Intel
drivers.  If you hit this case, when you try to bring the interface
back up it won't enable interrupts.  A reload of the driver module
fixes it of course.

So what we do is make sure all the sequences now go:

	napi_disable();
	atomic_set(&adapter->irq_sem, 0);
	*_irq_disable();

which makes sure the counter is always in the correct state.

Reported by Robert Olsson.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

http://bugzilla.kernel.org/show_bug.cgi?id=9493

The fib allows making identical routes with 'ip route replace'.
This patch makes the fib return -EEXIST if replacement would cause duplication.
Signed-off-by: NJoonwoo Park <joonwpark81@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

http://bugzilla.kernel.org/show_bug.cgi?id=9493

The fib allows making identical routes with 'ip route replace'.
This patch makes the fib return -EEXIST if replacement would cause duplication.
Signed-off-by: NJoonwoo Park <joonwpark81@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When looking for a conflicting connection the !sk->sk_bound_dev_if
check is performed only for live sockets, but not for timewait-ed.

This is not the case for ipv4, for __inet6_lookup_established in
both ipv4 and ipv6 and for other places that check for tw-s.

Was this missed accidentally? If so, then this patch fixes it and
besides makes use if the dif variable declared in the function.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code inspection turned up that error cases in rfkill_register() do not
call rfkill_led_trigger_unregister() even though we have already
registered.
Signed-off-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It was moved to arch/x86/lguest/Kconfig, but I lost the deletion part in a
patch suffle.  My confused one-liner "fix" to turn it on is also reverted:
84f7466eSigned-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The i386 and x86_64 arch directories contain nothing but a generated symlink
to arch/x86/boot/bzImage when a tree a built.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: NJosef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The PDC202xx older devices do not support ATAPI DMA via the usual
interfaces. What documentation I have isn't sufficient to support DMA and
it isn't clear if the Windows drivers do this or it is possible at all.
(Neither do the drivers/ide old drivers)

So turn it ATAPI DMA off, these are disk optimised controllers.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ipath: Fix receiving UD messages with immediate data

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (31 commits)
  Replace cpmac fix
  dl2k: the rest
  dl2k: MSCR, MSSR, ESR, PHY_SCR fixes
  dl2k: BMSR fixes
  dl2k: ANAR, ANLPAR fixes
  dl2k: BMCR_t fixes
  3c574, 3c515 bitfields abuse
  sbni endian fixes
  wan/lmc bitfields fixes
  dscc4 endian fixes
  S2io: Fixed synchronization between scheduling of napi with card reset and close
  atl1: fix frame length bug
  Documentation: add a guideline for hard_start_xmit method
  Revert "sky2: remove check for PCI wakeup setting from BIOS"
  e1000e Kconfig: remove ref to nonexistant docs
  bonding: Don't hold lock when calling rtnl_unlock
  bonding: fix lock ordering for rtnl and bonding_rwsem
  bonding: Fix up parameter parsing
  bonding: release slaves when master removed via sysfs
  bonding: fix locking during alb failover and slave removal
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] clarify watchdog operation in documentation
  [WATCHDOG] Revert "Stop looking for device as soon as one is found"

* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
  x86: add support for the latest Intel processors to Oprofile

There's currently no way to turn on Lguest guest support; the planned
Kconfig virtualization reorg didn't get into 2.6.25.

This was unnoticed because if you already had CONFIG_LGUEST_GUEST=y in
your config, it worked.  Too bad about new users...

Also, the Kconfig help was wrong now the virtio drivers are merged.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The latest Intel processors (the 45nm ones) have a model number of 23
(old ones had 15); they're otherwise compatible on the oprofile side.
This patch adds the new model number to the oprofile code.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

It was not clear what the difference is/was between the 
nowayout feature and the Magic Close feature.
Signed-off-by: N"Andrew Dyer" <amdyer@gmail.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This reverts commit 3ff6eb4a.

the !found check in the for loop allready made sure that only one
device was found.
Signed-Off-By: NPádraig Brady <P@draigBrady.com>
Signed-Off-By: NWim Van Sebroeck <wim@iguana.be>

Please apply this patch since i reverted by mistake
the commit 4e3ab47a
in 6cd043d9Signed-off-by: NMatteo Croce <technoboy85@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

remove an unused union-with-bitfield of the same sort,
add missing conversions in debugging printk
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

same story, different registers...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

broken use of bitfields; FUBAR on big-endian (and not valid C,
strictly speaking).
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

wn3_config is shared by these cards; the way we deal with it is both bad C
(union abuse) and broken on big-endian.  For 3c515 it's less serious (ISA
cards are quite rare outside of little-endian boxen), but 3c574 is a pcmcia
one and that'd better be endian-independent...  Fix is the same in both
cases.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Fixed synchronization between scheduling of napi with card reset and close
  by moving the enabling and disabling of napi to card up and card down
  functions respectively instead of open and close.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver sets up the hardware to accept a frame with max length
equal to MTU + Ethernet header + FCS + VLAN tag, but we neglect to
add the VLAN tag size to the ingress buffer.  When a VLAN-tagged
frame arrives, the hardware passes it, but bad things happen
because the buffer is too small.  This patch fixes that.

Thanks to David Harris for reporting the bug and testing the fix.
Tested-by: NDavid Harris <david.harris@cpni-inc.com>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add a guideline not to modify SKBs.
Signed-off-by: NMatti Linnanvuori <mattilinnanvuori@yahoo.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This reverts commit 84cd2dfb.

Some BIOS's break if Wake On Lan is enabled, and the machine
can't boot. Better to have some user's have to call ethtool to
enable WOL than to break a single user's boot.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge branch 'fixes-jgarzik' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes

There is no Documentation/networking/e1000e.txt.
Signed-off-by: NJason Uhlenkott <jasonuhl@jasonuhl.org>
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge branch 'ipg-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/romieu/netdev-2.6 into upstream-fixes

Change bond_mii_monitor to not hold any locks when calling rtnl_unlock,
as rtnl_unlock can sleep (when acquring another mutex in netdev_run_todo).

Bug reported by Makito SHIOKAWA <mshiokawa@miraclelinux.com>, who
included a different patch.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix the handling of rtnl and the bonding_rwsem to always be acquired
in a consistent order (rtnl, then bonding_rwsem).

The existing code sometimes acquired them in this order, and sometimes
in the opposite order, which opens a window for deadlock between ifenslave
and sysfs.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	A recent change to add an additional hash policy modified
bond_parse_parm, but it now does not correctly match parameters passed in
via sysfs.

	Rewrote bond_parse_parm to handle (a) parameter matches that
are substrings of one another and (b) user input with whitespace (e.g.,
sysfs input often has a trailing newline).
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>