RTL8852C use a later version Wi-Fi firmware, there are some parameters
need to be defined. These new parameter can avoid some unexpected
TDMA mode while Wi-Fi enter/leave lps.
Signed-off-by: NChing-Te Ku <ku920601@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-6-pkshih@realtek.com

Add a part of logic to parse type of ctrl report from firmware, and
remove Bluetooth packet counter count from driver, the feature was
moved to firmware at rtl8852c.
Signed-off-by: NChing-Te Ku <ku920601@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-4-pkshih@realtek.com

To configure the different chips with different coexistence version,
separated the firmware feature version matching number is necessary.
Signed-off-by: NChing-Te Ku <ku920601@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-3-pkshih@realtek.com

Update scoreboard setting to let Bluetooth know Wi-Fi power save state.
Signed-off-by: NChing-Te Ku <ku920601@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-2-pkshih@realtek.com

In current flow, FW is asynchronously loaded after alloc_hw(). It defers
the decision on FW feature map. It makes things difficult for us to decide
whether to hook chanctx ops, which should be decided while alloc_hw() is
calling. Still, asynchronous gets its advantages. So, we want to resolve
this without dropping them.

Based on multi-FW flag, RTW89_MFW_SIG, we can determine runtime FW is
multi-FW (MFW) or single FW (SFW). Both of them have a quite small chunk
for header at the head. The difference is that MFW doesn't describe version
code in its header while SFW does. So, we plan to extend MFW header for
version code. After that, in both cases, we can determine FW feature map by
just FW header. And, according to the map, we can decide chanctx.

So, we call request_partial_firmware_into_buf() to request a quite small
chunk before alloc_hw() to get a early FW feature map without affecting
things much and only use early map to decide whether to hook chanctx ops.

It means that if non-extended MFW is used at runtime, driver just acts
without chanctx as before. If extended MFW or SFW, which supports required
FW features, is used at runtime, driver can hook chanctx ops to mac80211 if
chip has configured support_chanctx_num > 0.

Besides, key point for now to support single one chanctx is whether HW scan
is supported at runtime. So, we configure all chip's support_chanctx_num to
1, and check if HW scan is supported at runtime via early FW feature map.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-14-pkshih@realtek.com

Some HW features are required if we hook chanctx ops to mac80211. With it,
mac80211 would expect the HW-supported variant ops exists on some behavior,
e.g. HW scan. But, HW features may depend on chip's FW or its development.
Besides, how many chanctx can be supported also depends on chip design.
We can neither decide whether to generally support chanctx ops nor how many
chanctx can be supported.

So, support_chanctx_num is added under chip info to deal with this by chip.
For now, all chip configure support_chanctx_num as 0. We haven't really
hook chanctx ops yet. So, chip can run without mac80211 chanctx as before.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-13-pkshih@realtek.com

Support mac80211 chanctx series ops. Still, currently support
single channel. Based on this premise, things should be similar
to before. So, we haven't dealt with relationship between vif
and chanctx in depth. Instead, we leave both ::assign_vif()
and ::unassign_vif() as noops for now.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-12-pkshih@realtek.com

After supporting more than one channel, we need entity mode to decide
how to set current channel(s) on the sub-entities. This decision may
happen on set_channel() and rtw89_core_set_chip_txpwr().

For now, we support single one channel and use only first HW entry,
i.e. RTW89_SUB_ENTITY_0, RTW89_MAC_0, RTW89_PHY_0. Without something
unexpected, the entity mode should always be RTW89_ENT_MODE_SCC after
recalcated, where SCC means single channel concurrency. So, an assert
is added in set_channel() and rtw89_core_set_chip_txpwr().
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-11-pkshih@realtek.com

While idle, we need a default chandef to set channel for things,
such as scan. Before support of mac80211 chanctx, mac80211 would
configure a default one on ieee80211_hw::conf::chandef. And we
just queried it whenever we did set channel. However, after support
of mac80211 chanctx, the flow won't work like before.

Besides, we don't now query chandef from ieee80211_hw::conf::chandef
either. So, similar to mac80211 without using chanctx, we configure
the default chandef with ieee80211_channel of index 0 in 2GHz.

Although we have not added the support of mac80211 chanctx here,
this configuration should be compatible before that. So, we commit
this ahead.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-10-pkshih@realtek.com

Originally, we didn't support mac80211 chanctx, so it's expected that
ieee80211_hw::conf::chandef would be filled by mac80211. And then, we
could just query it whenever we need the current chandef.

However, we are planing to support mac80211 chanctx. After that, the
above assumption would be broken. So, we adjust a bit ahead to reduce
future works about mac80211 chanctx.

After this, we don't query ieee80211_hw::conf::chandef directly, and
we add a map, entity_map, to HAL to indicate which chandef came from
stack. And it will later be used to recalcate entity mode.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-9-pkshih@realtek.com

For future support on multiple channels by multiple sub-entities,
we need to manage parameters of each channel instance like rtw89_chan,
rtw89_mac_idx, rtw89_phy_idx. So, we adjust related channel callback
functions and centrally conrtol these parameters in set_channel().
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-8-pkshih@realtek.com

For future support on multiple channels, there will be settings of
multiple sub-entities that we need to control. We don't want such
settings to be scattered all over the place. So, we centrally manage
controls of rtw89_phy_idx for RFK in set_channel().
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-7-pkshih@realtek.com

For future support on multiple channels, it would be disturbing if we
still allow scattered leaf functions of TX power to query and manage
channel related control by themselves.

So, query rtw89_chan only on top functions. Then, pass it via functions
to make sure that the values coming from the same struct rtw89_chan.

Besides, fix rtw8852a_set_txpwr_offset() from rtw8852a_set_txpwr_ctrl()
to rtw8852a_set_txpwr(). TX power offset should consider current band,
so move it to chip_ops::set_txpwr() which will be called every time that
channel is set.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-6-pkshih@realtek.com

Sometimes we need to write current rtw89_chan outside set_channel(),
e.g. during HW scan, we adjust it to align FW process through C2H.
However, we don't have full parameters to fill entire rtw89_chan.
And it will breakage if we update only part of current rtw89_chan.
That is what we don't want to see because most flows throughout
driver treat rtw89_chan as a whole.

So, we divide struct rtw89_chan to basic part and derived part. The
basic part contains the parameters which we are always able to know.
And the derived part will be calculated by the basic part. Then, a
central function, rtw89_chan_create(), is added to deal with this.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-5-pkshih@realtek.com

We are planning to support mac80211 chanctx. To reduce future works,
the driver architecture is adjusted first to isolate related things.

According to chip, our HW may have multiple sub-entities to support
multiple mac80211 chanctx. Struct rtw89_chan has been introduced for
things about channel/band/subband/... Now introduce struct rtw89_chan_rcd
to record difference after assigning new one of struct rtw89_chan.

We will implement and support chanctx with single channel first, i.e.
only use entry in RTW89_SUB_ENTITY_0, before handling dual channels.

Our hierarchy in planning will become as the following.
DEV
-> HAL
---> entity (manage status across sub-entities)
-----> sub-entity[*] (support mac80211 chanctx)
where each sub-entity contains one struct rtw89_chan.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-4-pkshih@realtek.com

Introduce struct rtw89_chan ahead to encapsulate stuffs from struct
rtw89_channel_params. These stuffs have a clone in HAL and are used
throughout driver. After multiple channels support, it's expected that
each channel instance has a configuration of them. So, we refine them
with struct rtw89_chan by precise type first, and will re-arrange HAL
by struct rtw89_chan in the following as well.

(No logic has changed.)
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-3-pkshih@realtek.com

We need to invoke the callback of the changed band at the first
set_channel() after every power-off. Originally, we forced the
channel to be 0 when doing power-off, and then determined things
by comparing channel with 0.

However, deciding on such things by channel might be confusing.
It's also confusing to use this kind of decision when we consider
multiple channels in the follow-up patches. So, another flag,
entity_active, is added ahead to HAL to deal with this.

Besides, we also need to check if entity is active when we set
TX power.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-2-pkshih@realtek.com

Somehow, firmware could report invalid TX rate, and we consider the
invalid rate as 0 that will make a wrong decision. So, drop invalid
reports, and also suppress the warning message.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-9-pkshih@realtek.com

To improve VO throughput, we enable VO TX AMPDU.

We measure the latency of enable or disable VO TX AMPDU. The experimental
results show that the difference between the two is insignificant only
300µs, so the little impact can be ignored for user experience.

Moreover, we found some APs will have a group key handshake timeout issue
when the EAPOL's TID is already setup BA session. Therefore, when
transmitting EAPOL, if EAPOL's TID BA session is already setup, we need
to delete it.
Signed-off-by: NKuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-7-pkshih@realtek.com

In STA mode, if peer is TDLS. Allocate a BSSID CAM entry with peer's
address to match address properly, and then hardware can ACK peer's
packets and receive packets to driver.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-4-pkshih@realtek.com

Normally, we only allocate an address CAM and single one MAC ID to AP in
STA mode. To support TDLS, we handle TDLS peers like AP handles stations.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-2-pkshih@realtek.com

We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.

Some adjustments were done with the following spatch:

    @@
    expression sdata;
    struct ieee80211_vif *vifp;
    identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
    @@
    (
    -sdata->vif.bss_conf.var
    +sdata->vif.cfg.var
    |
    -vifp->bss_conf.var
    +vifp->cfg.var
    )

    @bss_conf@
    struct ieee80211_bss_conf *bss_conf;
    identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
    @@
    -bss_conf->var
    +vif_cfg->var

(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add an new state, RTW89_PHY_DCFO_STATE_HOLD, to keep CFO acceleration
after CFO_PERIOD_CNT if the traffic is UL-OFDMA, which is calculated
based on RX trigger frame counter.
Signed-off-by: NEric Huang <echuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-4-pkshih@realtek.com

Adding this allows us to maintain trigger frame statistics, which is
required for our CFO tracking decisions.
Signed-off-by: NPo Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-3-pkshih@realtek.com

Since SAR is more expected to follow U-NII bands to plan subbands,
division of 6GHz band is quite different from defined enum of subbands
which is used by PHY in most cases. It's hard and painful if we want to
keep using the same enum on SAR. So, we introduce another enum for SAR
subbands and adjust SAR flow to use it.

Besides, since 6GHz SAR subbands won't be divided with edge alignment,
some cases will span two SAR subbands. For these cases, we describe them
within an array of rtw89_sar_span and take the smaller one between SAR
settings of the two subbands.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-6-pkshih@realtek.com

RX DCK is receiver DC calibration. To keep good RF performance, do this
calibration again if the delta of thermal value from the last calibration
is more than 8.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-5-pkshih@realtek.com

Before 6 GHz band was supported, i.e. only 2 GHz and 5 GHz, they were the
same from the numerical point of view. However, after 6 GHz band support,
we need to do this conversion logically.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-6-pkshih@realtek.com

DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.

Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.

8852c needs two backup buffers, so we enlarge the array. But, 8852a still
needs only one, so it only uses first element (index zero).
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-9-pkshih@realtek.com

IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-8-pkshih@realtek.com

LCK is short fro LC Tank calibration. Do this calibration once driver
loads RF parameters table. Since the characteristic can be changed by
temperature, we do this calibration again if difference of thermal value
is over a threshold.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-4-pkshih@realtek.com

8852c propose new API to configure BB TX/RX path. Without fix patch, it
can't transmit any packet.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-11-pkshih@realtek.com

IQK results in hardware has two copies that are used by firmware to switch
these two to support MCC.

This H2C tell firmware the corresponding channel and band of each IQK
results, and currrent one.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-10-pkshih@realtek.com

When disconnecting, it warns somethings after power is off, and we can't
do HCI IO. So, add this patch to avoid below messages:

  rtw89_8852ce 0000:03:00.0: timed out to flush pci txch: 11
  rtw89_8852ce 0000:03:00.0: failed to pre-release fwcmd
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-9-pkshih@realtek.com

In low power mode, we need to pause PCI to configure IMR and PCI ring
index registers accordingly, because the regular registers are power-off
in this mode.

In the transition moment named paused in code, we can't touch ring index,
so don't kick off DMA immediately. Instead, queue them into pending queue,
and kick off after the moment.

There are three low power modes, which are RF off/clock gate/power gate,
but PCI enter low power mode in later two modes only. So, add a mask
to achieve this.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-7-pkshih@realtek.com

Define efuse struct to access gain offset, and store them for further use
by setting channel.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-8-pkshih@realtek.com

Add parser for bb gain table and configure bb gain table for 8852c.
While ctrl_ch, obtain bb gain error settings and write them to phy.
Signed-off-by: NZong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-7-pkshih@realtek.com

TSSI is used to manage TX power with thermal value as a factor. This patch
is to configure bandedge to TX proper waveform.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-5-pkshih@realtek.com

TX power depends on rate, but must follow regulation for specific country.
Once asked to set channel, we configure registers according to these TX
power tables.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-3-pkshih@realtek.com

These parameters are used to initialize BB and RF hardware when we are
going to bring up interface and start to transmit and receive.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-2-pkshih@realtek.com

Add to configure security CAM while mac80211 calls set_key and del_key.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-4-pkshih@realtek.com