Clean up receive processing by dropping the character pointer and
keeping the length argument unchanged throughout the function.

Also make it more apparent that sysrq processing can consume a
characters by adding an explicit continue.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Use an unsigned type for the process-packet buffer argument and give it
a more apt name.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This device presents itself as a USB hub with three attached devices:
 - An ACM serial port connected to the GPS module (not affected by this
   commit)
 - An FTDI serial port connected to the GPS module (1546:0502)
 - Another FTDI serial port connected to the ODIN-W2 radio module
   (1546:0503)

This commit registers U-Blox's VID and the PIDs of the second and third
devices.

Datasheet: https://www.u-blox.com/sites/default/files/C099-F9P-AppBoard-Mbed-OS3-FW_UserGuide_%28UBX-18063024%29.pdfSigned-off-by: NFabio D'Urso <fabiodurso@hotmail.it>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Both devices added here have a FTDI chip inside. The device from Echelon
is called 'Network Interface' it is actually a LON network gateway.

 ID 0403:8348 Future Technology Devices International, Ltd
 https://www.eltako.com/fileadmin/downloads/de/datenblatt/Datenblatt_PL-SW-PROF.pdf

 ID 0920:7500 Network Interface
 https://www.echelon.com/products/u20-usb-network-interfaceSigned-off-by: NBeni Mahler <beni.mahler@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Enable support for cbus gpios on FT232H. The cbus configuration is
stored in two words in the EEPROM at byte-offset 0x1a with the mux
config for ACBUS5, ACBUS6, ACBUS8 and ACBUS9 (only pins that can be
configured as I/O mode).

Tested using FT232H by configuring one ACBUS pin at a time.
Reviewed-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NMatthew Michilot <matthew.michilot@gmail.com>
[ johan: fix copy-paste error in commit message ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the
second channel is available for use as a serial port.
Signed-off-by: NAndreas Fritiofson <andreas.fritiofson@unjo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

While there are a mix of things here, most of the stuff
were written from Kernel developer's PoV. So, add them to
the driver-api book.

A follow up for this patch would be to move documents from
there that are specific to sysadmins, adding them to the
admin-guide.
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: NJohan Hovold <johan@kernel.org>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This adds the USB ID of the Hjelmslund Electronics USB485 Iso stick.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

There is a bug in the current GPIO code for ftdi_sio: it failed to take USB
autosuspend into account. If the device is in autosuspend, calls to
usb_control_msg() fail with -EHOSTUNREACH. Because the standard value for
autosuspend timeout is usually 2-5 seconds, this made it almost impossible
to use the GPIOs on machines that have USB autosuspend enabled. This patch
fixes the issue by acquiring a PM lock on the device for the duration of
the USB transfers. Tested on an FT231X device.
Signed-off-by: NKaroly Pados <pados@pados.hu>
[ johan: simplify code somewhat ]
Fixes: ba93cc7d ("USB: serial: ftdi_sio: implement GPIO support for FT-X devices")
Cc: stable <stable@vger.kernel.org>	# 4.20
Signed-off-by: NJohan Hovold <johan@kernel.org>

Improve baud-rate generation by using rounding-to-closest instead of
truncation in divisor calculation.

Results have been verified by logic analyzer on an FT232RT (232BM) chip.
The following table shows the wanted baud rate, the baud rate obtained
with the old method (truncation), with the new method (rounding) and the
baud rate generated by the windows 10 driver. The numbers in parentheses
is the error.

+- Wanted --+------ Old -------+------ New -------+------ Win -------+
|    9600   |    9600 (0.00%)  |    9604 (0.05%)  |    9605 (0.05%)  |
|   19200   |   19200 (0.00%)  |   19199 (0.01%)  |   19198 (0.01%)  |
|   38400   |   38395 (0.01%)  |   38431 (0.08%)  |   38394 (0.02%)  |
|   57600   |   57725 (0.22%)  |   57540 (0.10%)  |   57673 (0.13%)  |
|  115200   |  115307 (0.09%)  |  115330 (0.11%)  |  115320 (0.10%)  |
|  921600   |  919963 (0.18%)  |  920386 (0.13%)  |  920810 (0.09%)  |
|  961200   |  996512 (3.67%)  |  956480 (0.49%)  |  956937 (0.44%)  |
+-----------+------------------+------------------+------------------+

The error due to noise in the measurements is in the order of a few
tenths of a %. As can be seen, the baud rate is significantly improved
for some rates (e.g. 961200), and corresponds to the output given by the
windows driver.

The theoretical baud rate has been calculated for all baud rates from 1
to 3M, and as expected, the error is centered around 0, with a triangle
shape instead of a sawtooth, so the maximum error is decreased to half.
Signed-off-by: NNikolaj Fogh <nikolajfogh@gmail.com>
[ johan: edit commit message slightly ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Enable support for cbus gpios on FT232R. The cbus configuration is
stored in one word in the EEPROM at offset 0x0a (byte-offset 0x14) with
the mux config for CBUS0, CBUS1, CBUS2 and CBUS3 in bits 0..3, 4..7,
8..11 and 12..15, respectively.

Tested using FT232RL by configuring one cbus pin at a time.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop the gpio line names, which cause gpiolib to complain loudly
whenever a second ftdi gpiochip is registered:

	gpio gpiochip5: Detected name collision for GPIO name 'CBUS0'
	gpio gpiochip5: Detected name collision for GPIO name 'CBUS1'
	gpio gpiochip5: Detected name collision for GPIO name 'CBUS2'
	gpio gpiochip5: Detected name collision for GPIO name 'CBUS3'

and also prevents the legacy sysfs interface from being used (as the
line names are used as device names whenever they are set):

	sysfs: cannot create duplicate filename '/class/gpio/CBUS0'

Until non-unique names are supported by gpiolib (without warnings and
stack dumps), let's leave the gpio lines unnamed.
Signed-off-by: NJohan Hovold <johan@kernel.org>

This patch allows using the CBUS pins of FT-X devices as GPIO in CBUS
bitbanging mode. There is no conflict between the GPIO and VCP
functionality in this mode. Tested on FT230X and FT231X.

As there is no way to request the current CBUS register configuration
from the device, all CBUS pins are set to a known state when the first
GPIO is requested. This allows using libftdi to set the GPIO pins
before loading this module for UART functionality, a behavior that
existing applications might be relying upon (though no specific case
is known to the authors of this patch).
Signed-off-by: NKaroly Pados <pados@pados.hu>
[ johan: minor style changes ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Clean up the somewhat convoluted hardware-assisted flow control
handling.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop urb_ prefixes from value and index variables used in control
requests.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Replace all __u types with their u counterparts throughout the driver
(whose structures are not exported to user space).
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Since forever this driver has had IXON and IXOFF mixed up, and has used
the latter rather than the former to enable hardware-assisted software
flow control on output.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.

This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Signed-off-by: NVasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This reverts commit 79a0b331.

Turns out this is not an FTDI device after all.

Fixes: 79a0b331 ("USB: serial: ftdi_sio: add Id for Physik Instrumente E-870")
Reported-by: NMartin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for the Physik Instrumente E-870 PIShift Drive
Electronics, a Piezo motor driver.
Signed-off-by: NMartin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add device id for Harman FirmwareHubEmulator to make the device
auto-detectable by the driver.
Signed-off-by: NClemens Werther <clemens.werther@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: NMajor Hayden <major@mhtx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_WO() macro instead, which does everything properly instead.

This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: NJoe Perches <joe@perches.com>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: NJohan Hovold <johan@kernel.org>
Acked-by: NShuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add AIRBUS_DS_P8GR device IDs to ftdi_sio driver.
Signed-off-by: NMax Schulze <max.schulze@posteo.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner.  So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text.  And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.

This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add CYPRESS_VID vid and CYPRESS_WICED_BT_USB and CYPRESS_WICED_WL_USB
device IDs to ftdi_sio driver.
Signed-off-by: NJeffrey Chu <jeffrey.chu@cypress.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Remove the broken alt_speed code, and warn when trying to set the line
speed using TIOCSSERIAL and SPD flags.

The use of SPD flags to set the line speed has been deprecated since
v2.1.69 and support for alt_speed (e.g. "warp") has even been removed
from TTY core in v3.10 by commit 6865ff22 ("TTY: do not warn about
setting speed via SPD_*"), effectively breaking all driver
implementations of this except for serial core.

Also remove the verbose and outdated comment on how to set baud rates.

Note that setting a custom divisor will continue to work with the
caveat that 38400 must again be selected every time the divisor is
changed since v2.6.24 and commit 669a6db1 ("USB: ftd_sio: cleanups
and updates for new termios work") which started reporting back the
actual baud rate used.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Simplify TIOCSSERIAL flag logic somewhat.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for recognition of ARM-USB-TINY(H) devices which
are almost identical to ARM-USB-OCD(H) but lacking separate barrel jack
and serial console.

By suggestion from Johan Hovold it is possible to replace
ftdi_jtag_quirk with a bit more generic construction. Since all
Olimex-ARM debuggers has exactly two ports, we could safely always use
only second port within the debugger family.
Signed-off-by: NAndrey Korolyov <andrey@xdel.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Commit 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY
flag") enables unprivileged users to set the FTDI latency timer,
but there was a logic flaw that skipped sending the corresponding
USB control message to the device.

Specifically, the device latency timer would not be updated until next
open, something which was later also inadvertently broken by commit
c19db4c9 ("USB: ftdi_sio: set device latency timeout at port
probe").

A recent commit c6dce262 ("USB: serial: ftdi_sio: fix extreme
low-latency setting") disabled the low-latency mode by default so we now
need this fix to allow unprivileged users to again enable it.
Signed-off-by: NAnthony Mallet <anthony.mallet@laas.fr>
[johan: amend commit message]
Fixes: 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY flag")
Fixes: c19db4c9 ("USB: ftdi_sio: set device latency timeout at port probe").
Cc: stable <stable@vger.kernel.org>     # 2.6.31
Signed-off-by: NJohan Hovold <johan@kernel.org>

This development kit has an FT4232 on it with a custom USB VID/PID.
The FT4232 provides four UARTs, but only two are used. The UART 0
is used by the FlashPro5 programmer and UART 2 is connected to the
SmartFusion2 CortexM3 SoC UART port.

Note that the USB VID is registered to Actel according to Linux USB
VID database, but that was acquired by Microsemi.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The 'store' function for the "event_char" device attribute currently
expects a base 10 value.  The value is composed of an enable bit in bit
8 and an 8-bit "event character" code in bits 7 to 0.  It seems
reasonable to allow hexadecimal and octal numbers to be written to the
device attribute in addition to decimal.  Make it so.

Change the debug message to show the value in hexadecimal, rather than
decimal.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The "event_char" device attribute value, when written, is interpreted as
an enable bit in bit 8, and an "event character" in bits 7 to 0.

Return an error -EINVAL for out-of-range values.  Use kstrtouint() to
parse the integer instead of the obsolete simple_strtoul().
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Valid latency timer values are between 1 ms and 255 ms in 1 ms steps.
The store function for the "latency_timer" device attribute currently
allows any value, although only the lower 16 bits will be sent to the
device, and the device only stores the lower 8 bits.  The hardware
appears to accept the (invalid) value 0 and treats it the same as 1
(resulting in a latency of 1 ms).

Change the latency_timer_store() function to accept only the values 0 to
255, returning an error -EINVAL for out-of-range values.  Call
kstrtou8() to parse the integer instead of the obsolete
simple_strtoul().
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NJohan Hovold <johan@kernel.org>

If a BM type chip has iSerialNumber set to 0 in its EEPROM, an incorrect
value is read from the bcdDevice field of the USB descriptor, making it
look like an AM type chip.  Attempt to correct this in
ftdi_determine_type() by attempting to read the latency timer for an AM
type chip if it has iSerialNumber set to 0.  If that succeeds, assume it
is a BM type chip.

Currently, read_latency_timer() bails out without reading the latency
timer for an AM type chip, so factor out the guts of
read_latency_timer() into a new function _read_latency_timer() that
attempts to read the latency timer regardless of chip type, and returns
either the latency timer value or a negative error number.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The latency timer was introduced with the FT232BM and FT245BM chips.  Do
not bother attempting to read or write it for older chip versions.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NJohan Hovold <johan@kernel.org>

FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).

When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.

In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.

This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: NMichael Walle <michael@walle.cc>
Fixes: 72fda3ca ("USB: serial: ftd_sio: implement sysrq handling on
break")
Fixes: 166ceb69 ("USB: ftdi_sio: clean up line-status handling")
Cc: stable <stable@vger.kernel.org>	# v2.6.35
Signed-off-by: NJohan Hovold <johan@kernel.org>