Merge tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "ARM: rockchip: dts changes for 4.1" from Heiko Stuebner:

This adds and enables the usbphy nodes on the rk3288 boards and enables
the gmac on the firefly board. A new board the Popmetal-rk3288 is also
added. And finally the pmic supplies for act8846 based boards are added,
as the act8865/act8846 driver gained supply handling in the regulator tree.

* tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: complete rk3288-evb pmic supplies
  ARM: dts: rockchip: add input supplies for the act8846 on Radxa Rock
  ARM: dts: add rk3288 PopMetal board
  dt-bindings: add root compatible property for PopMetal board
  ARM: dts: rockchip: enable gmac on rk3288-firefly
  ARM: dts: rockchip: enable usbphy on rk3288-firefly
  ARM: dts: rockchip: Enable usb PHY on rk3288-evb board
  ARM: dts: rockchip: add rk3288 usb PHY
Signed-off-by: NOlof Johansson <olof@lixom.net>

File uses dash in the filename, not underscore.
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Pull "This pull request contains the following changes from Ray for Cygnus SoCs: from Florian Fainelli:

- enable IOMUX, required for pinmux/pinctrl
- enable GPIO, required for the GPIO driver
- enable GPIO hook detection for BCM911360-based phone designs
- enable PCIe controller for the bcm958300k designs

* tag 'arm-soc/for-4.1/devicetree-part-2' of http://github.com/broadcom/stblinux:
  ARM: dts: enable PCIe support for Cygnus
  ARM: dts: cygnus: enable GPIO based hook detection
  ARM: dts: enable GPIO for Broadcom Cygnus
  ARM: dts: enable IOMUX for Broadcom Cygnus

This patch introduces devicetree for the Alpine platform, and
for a development board based on the same platform.
Signed-off-by: NBarak Wasserstrom <barak@annapurnalabs.com>
Signed-off-by: NTsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there.
Only enable them for bcm958300k where PCIe interfaces are populated
Signed-off-by: NRay Jui <rjui@broadcom.com>
Reviewed-by: NScott Branden <sbranden@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

This adds the static vcc_sys regulator to the rk3288-evb, the missing
rk808 supplies from it and all the supplies of the act8846 evb-variant.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Merge tag 'renesas-dt2-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.1" from Simon Horman:

* ape6evm board
  - Configure GPIO keys as wake-up source
  - Enable pull-up for GPIO switches
  - Correct polarity of LEDs
* r8a7791 SoC
  - Correct IPMMU-GP clock to device tree
* r8a7794 SoC
  - Correct ethernet controller PHY IRQ
* lager, koelsch and marzen boards
  - Add DU external pixel clock to DT
* lager board
  - Add HDMI output support to DT
* r8a7791 and r8a7790 SoCs
  - Tidy up SDHI register size in DT
  - Reference DMA channels for SDHI in DT

* tag 'renesas-dt2-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: ape6evm dts: Configure the custom switch as wake-up source
  ARM: shmobile: ape6evm dts: Enable pull-up for GPIO switches
  ARM: shmobile: r8a7791: Fix IPMMU-GP clock to device tree
  ARM: shmobile: r8a7794: alt: Fix ethernet controller PHY IRQ line
  ARM: shmobile: lager: Add DU external pixel clocks to DT
  ARM: shmobile: koelsch: Add DU external pixel clocks to DT
  ARM: shmobile: marzen: Add DU external pixel clock to DT
  ARM: shmobile: ape6evm dts: Fix polarity of LEDs
  ARM: shmobile: lager: Add DU HDMI output support
  ARM: shmobile: r8a7791: Fix HSUSB clock to hp_clk from mp_clk
  ARM: shmobile: r8a7790: Fix HSUSB clock to hp_clk from mp_clk
  ARM: shmobile: r8a7791: tidyup SDHI register size on DTSI
  ARM: shmobile: r8a7790: tidyup SDHI register size on DTSI
  ARM: shmobile: r8a7791: Reference DMA channels in SDHI DT nodes
  ARM: shmobile: r8a7790: Reference DMA channels in SDHI DT nodes

Pull "mvebu dt changes for v4.1 (part #1)" from Gregory CLEMENT:

- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board

* tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: add Device Tree files for Armada 39x SoC and board
  ARM: mvebu: fix unit address of MPIC nodes
  ARM: mvebu: use stdout-path in all armada-*.dts
  ARM: mvebu: add serial port aliases on Armada 370/375/38x/XP
  ARM: mvebu: remove aliases for Ethernet devices on Armada 370/375/38x/XP
  ARM: mvebu: add UART labels to Armada 375
  ARM: mvebu: add missing UART labels on Armada 38x
  ARM: mvebu: fix usb@ unit address on Armada 38x to match register address
  ARM: mvebu: a385-db-ap: Enable the NAND
  ARM: ARMADA XP: WRT1900AC: Add support for the Ethernet switch
  ARM: Kirkwood: enable GPIO fan alarm support for 2Big Network v2
  ARM: mvebu: Fix MPIC unit address
  ARM: dts: dove: Add some more common pinctrl settings
  ARM: dts: dove: Add node labels for PCIe ports 0 and 1
  ARM: dts: dove: Always include gpio and interrupt-controller headers
  ARM: dts: dove: Fix uart[23] reg property
  ARM: mvebu: add Linksys WRT1900AC (Mamba) support
  ARM: mvebu: Add Device Tree description of SDHCI for Armada 388 RD
  ARM: mvebu: Update the SDHCI node on Armada 38x
  ARM: mvebu: Use macros for interrupt flags on Armada 38x sdhci node

Pull "Broadcom Device Tree changes for 4.1 #1" from Florian Fainelli:

This pull request contains the following Broadcom SoCs Device Tree changes:

- Jonathan adds support for the Broadcom Cygnus BCM958305K board

- Rafal adds support for Netgear R8000 and fixes the default for power LEDs
  on Netgear R6250

* tag 'arm-soc/for-4.1/devicetree' of http://github.com/broadcom/stblinux:
  ARM: BCM5301X: Fix default state of power LEDs on Netgear R6250
  ARM: BCM5301X: Add DT for Netgear R8000
  ARM: dts: Enable Broadcom Cygnus BCM958305K

Pull "First batch of DT changes for 4.1" into next/dt:

- at91sam9x5 & EK board: ISI and camera sensors
- at91sam9n12 & EK board: USB gadget nodes
- sama5d3: typos, gpio-keys on Xplained board
- sama5d4: i2c, leds, audio, ISI, crypto, pwm missing nodes
- new sama5d4 xplained board

* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: (31 commits)
  ARM: at91/dt: sama5d4: add ISI dt support
  ARM: at91/dt: sama5d4: add pwm0 device node
  ARM: at91/dt: sama5d4: add aes, sha and tdes nodes
  ARM: at91: dt: sama5d4ek: enable audio
  ARM: at91: dt: sama5d4ek: add and enable wm8904
  ARM: at91: dt: sama5d4ek: enable ssc0
  ARM: at91: dt: sama5d4: add ssc nodes
  ARM: at91/dt: sama5d4 xplained: add i2c0
  ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board
  ARM: at91/dt: sama5d4: add #{address, size}_cells properties for macb0
  ARM: at91/dt: sama5d4ek: add leds in DT node
  ARM: at91/dt: add i2c1 declaration to sama5d4
  ARM: at91/dt: gpio-keys: address-cells and size-cells properties are not needed
  ARM: at91/dt: at91-sama5d3_xplained: add gpio-key pinctrl property
  ARM: at91/dt/trivial: correct file headers for SAMA5D3 SoC peripherals
  ARM: at91/dt: at91sam9n12ek: enable udp
  ARM: at91/dt: at91sam9n12: add udp device node
  ARM: at91: at91sam9g25ek/dts: enable ISI and ov2640
  ARM: at91: at91sam9x5ek/dts: add ov2640 support
  ARM: at91: at91sam9x5/dts: add ISI dt support, include isi node, pinctrls
  ...

This enables GPIO based phone hook detection for Broadcom BCM911360
phone factor board (bcm911360_entphn)
Signed-off-by: NRay Jui <rjui@broadcom.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

This enables all 3 GPIO controllers including the ASIU GPIO, the
chipcommonG GPIO, and the ALWAYS-ON GPIO, for Broadcom Cygnus SoC
Signed-off-by: NRay Jui <rjui@broadcom.com>
Reviewed-by: NScott Branden <sbranden@broadcom.com>
Tested-by: NDmitry Torokhov <dtor@chromium.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

This enables the IOMUX support for Broadcom Cygnus SoC
Signed-off-by: NRay Jui <rjui@broadcom.com>
Tested-by: NDmitry Torokhov <dtor@chromium.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

On the Radxa Rock board most supplies come from the static 5v vsys supply, but
the inl1-supply comes from the REG4 of the act8846 itself. Model this dependency
using the added supply-handling to make sure the supplying regulator gets handled
correctly and not accidentially turned off.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

We want green LED to be enabled by default.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Reported-by: NIan Kent <raven@themaw.net>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The switches on r8a73a4/ape6evm do not have pull-up registers.  The
schematics say: "Need to use APE6 internal PullUp", hence enable pull-up
using pinctrl.

Without this, the switches don't really work, as the GPIO inputs are
more likely to pick up ghost signals through capacitive coupling than
actual keypresses.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Pull "meson DTS changes" from Carlo Caione:

- New DTS for MINIX NEO-X8
- Add DTS support for SPIFC, Ethernet controller and pinctrl

* tag 'for-v4.0-rc/meson-dts' of https://github.com/carlocaione/linux-meson:
  ARM: dts: meson: add DTS file for MINIX NEO-X8
  ARM: dts: meson8: add pinctrl node
  ARM: dts: meson: enable Ethernet controller
  ARM: dts: meson: add node for SPIFC

Merge tag 'renesas-dt-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM Based SoC DT Updates for v4.1" from Simon Horman:

* Increase hardware coverage of DT for various SoCs
* Add PFC information for emev2 SoC
* Remap entire APMU region for r8a7791 and r8a7790 SoCs
* Declare the full 512 MiB of RAM for kzm9g board
* Add selectable sources to DIV6 clocks to sh73a0 SoC
* Add missing INTCA0 clock for irqpin module on sh73a0 SoC
* Set control-parent for all irqpin node on sh73a0 SoC

* tag 'renesas-dt-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
  ARM: shmobile: r8a7794: add SDHI DT support
  ARM: shmobile: r8a7790: add ADSP clocks
  ARM: shmobile: r8a7791: add ADSP clocks
  ARM: shmobile: henninger: add CAN0 DT support
  ARM: shmobile: r8a7791: add CAN DT support
  ARM: shmobile: r8a7791: add CAN clocks
  ARM: shmobile: r8a7790: add CAN DT support
  ARM: shmobile: r8a7790: add CAN clocks
  ARM: shmobile: emev2-kzm9d dts: Add PFC information for uart1
  ARM: shmobile: emev2 dtsi: Add PFC information
  ARM: shmobile: r8a7791: smp: remap whole apmu region
  ARM: shmobile: r8a7790: smp: remap whole apmu region
  ARM: shmobile: koelsch: Add DU HDMI output support
  ARM: shmobile: r8a7791: Correct SDHI clock labels and output-names
  ARM: shmobile: r8a7794: Correct SDHI clock base address, labels and output-names
  ARM: shmobile: r8a7794: alt: Enable ethernet controller
  ARM: shmobile: r8a7794: Add ethernet controller to device tree
  ARM: shmobile: r8a7794: Add IPMMU DT nodes
  ARM: shmobile: r8a7791: Add IPMMU DT nodes
  ARM: shmobile: r8a7790: Add IPMMU DT nodes
  ...

PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).

This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

PopMetal board is a rk3288 based board made by ChipSpark, this
add root compatible property for it
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Add ISI dt node and pinctrl settings in sama5d4.dtsi.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: sort nodes in order. remove useless comments]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NLeilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable audio support for sama5d4ek board.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add wm8904 codec node and enable it.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable SSC0 node, which will be used for audio.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add SSC 0 and 1 nodes.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add i2c0 aka twi0 on sama5d4 xplained board.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add at91 sama5d4 xplained board support.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add the leds DT node in the dts file.
In the leds, d10 is set as heartbeat led.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add alias, node declaration and pinctrl for i2c1 (aka: twi1).
Signed-off-by: NPhilip Attfield <phil.attfield@seqlabs.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them in these new boards.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

File name had at91 prefix, which is not the case anymore for SAMA5D3.
AT91SAM9x5 was mentioned instead of SAMA5D3 SoC.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable usb device port on at91sam9n12ek board.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add usb device node for at91sam9n12.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>