There were still some corner cases where isoc transfer was not able to
restart, specially when missed isoc does not happen , and in fact gadget does
not queue any new request during giveback.

Cleanup function calls giveback first, which provides a way to queue
another request to gadget. But gadget did not had any data. So , it did
not call ep_queue. To twist it further, gadget did not queue till
cleanup for last queued TRB is called. If we ever reach this scenario,
we must call END TRANSFER, so that we receive a new  xfernotready with
information about current microframe number.

Also insure that there is no request submitted to core when issuing END
TRANSFER.

Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Its better to return from each if condition as they are mutually
exclusive.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are two reasons to generate missed isoc.

1. when the host does not poll for all the data.
2. because of application-side delays that prevent all the data from
being transferred in programmed microframe.

Current code was able to handle first case only.  This patch handles
scenario 2 as well.Scenario 2 sometime may occur with complex gadget
application, however it can be easily reproduced for testing purpose as
follows:

a. use isoc binterval as 1 in f_sourcesink.
b. use pattern=0
c. introduce a delay of 150us deliberately in source_sink_complete, so
that after few frames it lands into scenario 2.
d. now run testusb 16 (isoc in  test). You will notice that if this
patch is not applied then isoc transfer is not able to recover after
first missed.

Current patch's approach is as under:

If missed isoc occurs and there is no request queued then issue END
TRANSFER, so that core generates next xfernotready and we will issue a
fresh START TRANSFER.
If there are still queued request then wait, do not issue either END or
UPDATE TRANSFER, just attach next request in request_list during giveback.
If any future queued request is successfully transferred then we will issue
UPDATE TRANSFER for all request in the request_list.

Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Synopsys says:
The HIRD Threshold field must be set to ‘0’ when the device core is
operating in super speed mode.

This patch implements above statement.

Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we have an extra 'ret' variable shadowing a previous
definition. Remove it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If a USB transfer has already been started, meaning
we have already issued StartTransfer command to that
particular endpoint, DWC3_EP_BUSY flag has also
already been set.

When we try to cancel this transfer which is already
in controller's cache, we will not receive XferComplete
event and we must clear DWC3_EP_BUSY in order to allow
subsequent requests to be properly started.

The best place to clear that flag is right after issuing
DWC3_DEPCMD_ENDTRANSFER.

Cc: stable@vger.kernel.org # v3.4 v3.5 v3.6
Reported-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.

In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.

So, cache sync function must not be executed in case of ep0 bounced.

Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When connection is established non-ss mode, endpoint.maxburst is correctly set
to 0, this means that current code will set maxburst bitfield on DEPCFG's
parameter 0 to the highest possible value (0x0f) which is wrong.

Even though this hasn't caused any issues so far (HW seems to ignore that when
not running in SS mode) we want to make sure maxburst bitfield is only set to
anything other than zero if we're running on SuperSpeed mode. In order to
achieve that, let's check for gadget's operating speed before setting maxburst
bitfield when issuing DEPCFG command.

[ balbi@ti.com : improved commit log a bit in order to clarify the situation ]
Signed-off-by: NChanho Park <chanho61.park@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case some gadget driver tries to enable an endpoint
which is already enabled, we print a nice WARN so we
can track broken gadget drivers. The only problem is that
we're printing the WARN when we already changed endpoint's
name, which would result in endpoints named as:

ep1in-bulk-bulk-bulk-bulk-bulk-bulk-bulk

To prevent that, we will continue to print the WARN,
but do so before changing endpoint's name and return
early.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dwc3_stop_active_transfer has been called from two places. After each
calling of this function , we should allow 100 us delay to synchronize
with interconnect.

It would be better if we put this delay in that function only, rather
than into calling routine of this function.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Reported-by: NMichel Sanches <michel.sanches@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When MISSED_ISOC is set, BUSY is also set. Since, we are handling
MISSED_ISOC as a separate case in third scenario, therefore handle only
BUSY but not MISSED_ISOC in second scenario.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the following sparse warnings:

drivers/usb/dwc3/gadget.c:1096:7: warning: symbol 'ret' shadows an earlier one
drivers/usb/dwc3/gadget.c:1058:8: originally declared here
drivers/usb/dwc3/gadget.c:1100:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1118:16: warning: symbol 'dwc' shadows an earlier one
drivers/usb/dwc3/gadget.c:1057:15: originally declared here
drivers/usb/dwc3/gadget.c:1800:19: warning: symbol 'dep' shadows an earlier one
drivers/usb/dwc3/gadget.c:1778:18: originally declared here

Also, fix the potential checkpatch errors around the if() loops that
this fix patch can create.
Signed-off-by: NMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Databook says we should set Ignore Sequence Number bit
from ConnectDone Event, so let's do so.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Although timeout has never been experienced, still to make it
meaningful, its better to return error if it ever occurs.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As per databook, ACCEPT{U1,U2}ENA bits should be set after receiving
SetConfiguration Command.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

as per databook, these bits are cleared by hardware on each USB reset,
so no need to clear it explicitly by software in reset ISR.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

as per data book any HIRD threshold value greater than 4b1100 is
invalid. So set the maximum valid value as default values.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

set_halt for ep0 is called to stall a deferred control responses by the
gadget.  We already have a function to stall default control endpoint.
This patch points set_halt for ep0 to the already available function.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NMichel Sanches <michel.sanches@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

whenever we want to stall ep0, we always call
dwc3_ep0_stall_and_restart() which makes sure
to send ep0state properly rendering the code
in __dwc3_gadget_ep_set_halt() duplicated.
Reported-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

resource_index is more human readable. No
functional changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It makes it easier to read and also avoids
setting DWC3_EP_PENDING_REQUEST just so the
next branch evaluates true.

No functional changes otherwise.

Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Now we are sure that, if res_trans_idx is zero, then endpoint has been
stopped. So it's safe to just return if endpoint is already stopped. No
need to generate warning anymore.

While doing so, it's better to return when res_trans_idx is zero and
decrease one level of indentation.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>

[ balbi@ti.com: slightly changed commit log ]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case of ep_disable and reset interrupt is received and, still there
was at least one request queued for dma transfer, then endpoint is
stopped first. Once endpoint is stopped, callback for all queued
request must be called.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case of ep_dequeue , if dequeued request was submitted for dma
transfer, then endpoint is stopped. Once endpoint is stooped, callback
for the dequeued request must be called.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

bMaxBurst field on endpoint companion descriptor
is supposed to contain the number of burst minus
1. When passing that to controller drivers, we
should be passing the real number instead (by
incrementing 1).

While doing that, also fix the assumption on
dwc3 that value comes decremented by one.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It is needed to enumerate recent cores like 2.10a.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

By the time we're disabling the endpoint, HW
could already have posted more events to our
event buffer. In that case, we will receive
endpoint events for a disabled endpoint.

In order to protect ourselves from that situation,
we simply ignore endpoint interrupts whenever
the endpoint is disabled.
Tested-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case we get disconnected, we will call gadget
driver's disconnect method, which should make
sure to disable all endpoints. At that point
we will call stop_active_transfers() to make
sure we didn't leave any pending request on the
controller.
Tested-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

That IRQ is causing way too much trouble. We have
a different handling which was agreed with IP
provider and has been tested with FPGA and OMAP5.
Tested-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We never set CMDIOC bit for Start Transfer
command, so that code will never be used.
Tested-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If event status says that its last completed TRB but TRB is still owned
by HW then break from the loop, because we are not going to get correct
TRB status from trb control/size register.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If an IN transfer is missed on isoc endpoint, then driver must insure
that next ep_queue is properly handled.
This patch fixes this issue by starting a new transfer for next queued
request.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently in case of isoc, interrupt is programmed after each
TRB_NUM/4 ie 8th TRB. A TRB is programmed against each submitted
request from gadget. If we do not want to limit the minimum number of
necessary request to be submitted from gadget then we must receive
interrupt on each TRB submission. There can be such situation with a
gadget working with ping-pong buffer.

If a gadget does not want to receive interrupt after each request
completion then it may set no_interrupt flag.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to the databook, the DWC3 Core will
reset those bits to 0 on USB Bus Reset. This
means we must re-enable those bits on every
reset interrupt.

Because we will always get a Reset interrupt
after loading a gadget driver, we can, instead
of re-enabling something that was just lost,
move the handling of those bits to the Reset
Interrupt.

This patch fixes USB30CV U1/U2 Test.
Signed-off-by: NGerard CAUVY <g-cauvy1@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we get a disconnect IRQ, we should take
the core out of low power mode so we can
reconnect afterwards.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we don't read out the contents of the register
(in order to reinitialize 'reg' variable) we will
be writing unknown contents to the DCTL register
whenever we try to use dwc3_gadget_wakeup() function.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Recent cores (>= 1.94a) have a set of new features,
commands and a slightly different programming model.

This patch aims to support those changes.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

those two functions don't power PHYs, they simply
put them in suspend state. Rename to reflect better
what functions actually do.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>