se_io allows to send apdu over the CLF to the embedded
Secure Element.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some tag might get deactivated after some read or write tentative.
This may happen for example with Mifare Ultralight C tag when trying
to read the last 4 blocks (starting block 0x2c) configured as write
only.
NFC_CMD_ACTIVATE_TARGET will try to reselect the tag in order to
detect if it got remove from the field or if it is still present.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

nci_rf_deactivate_req only support NCI_DEACTIVATE_TYPE_IDLE_MODE.
In some situation, it might be necessary to be able to support other
NCI_DEACTIVATE_TYPE such as NCI_DEACTIVATE_TYPE_SLEEP_MODE in order for
example to reactivate the selected target.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

A notification for rf deaction can be IDLE_MODE, SLEEP_MODE,
SLEEP_AF_MODE and DISCOVERY. According to each type and the NCI
state machine is different (see figure 10 RF Communication State
Machine in NCI specification)
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The nci status byte was ignored. In case of tag reading for example,
if the tag is removed from the antenna there is no way for the upper
layers (aka: stack) to get inform about such event.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When switching from UICC to another, the CLF may signals to the Terminal
Host that some existing pipe are cleared for future update.

This notification needs to be "acked" by the Terminal Host with a ANY_OK
message.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If our terminal connect with other host like UICC, it may create
a pipe with us, the host controller will notify us new pipe
created, after that UICC will open that pipe, if we don't handle
that request, UICC may failed to continue initialize which may
lead to card emulation feature failed to work
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

se_io allows to send apdu over the CLF to the embedded Secure Element.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some NFC controller using NCI protocols may need a proprietary commands
flow to disable a secure element
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some NFC controller using NCI protocols may need a proprietary commands
flow to enable a secure element
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

NFC: nci: Update nci_discover_se to run proprietary commands to discover all available secure element

Some NFC controller using NCI protocols may need a proprietary commands
flow to discover all available secure element
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fix sparse warning introduced by commit: 9e87f9a9

It was generating the following warning:
net/nfc/nci/ntf.c:170:7: sparse: symbol 'nci_get_prop_rf_protocol' was not declared. Should it be static?

Procedure to reproduce it:
# apt-get install sparse
  git checkout 9e87f9a9
  make ARCH=x86_64 allmodconfig
  make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

se_io allows to send apdu over the CLF to the embedded Secure Element.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Before signaling the deactivation, send a deactivation request if in
RFST_DISCOVERY state because neard assumes polling is stopped and will
try to restart it.
Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When the deactivation type reported by RF_DEACTIVATE_NTF is Discovery, go in
RFST_DISCOVERY state. The NFCC stays in Poll mode and/or Listen mode.
Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

As specified in NCI 1.0 and NCI 1.1, when using the NFC-DEP RF Interface, the
DH and the NFCC shall only use the Static RF Connection for data communication
with a Remote NFC Endpoint.
Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Target responds to the ATR_REQ with the ATR_RES. Configure the General
Bytes in ATR_RES with the first three octets equal to the NFC Forum LLCP
magic number, followed by some LLC Parameters TLVs described in section
4.5 of [LLCP].
Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Changes:

 * Extract the Listen mode activation parameters from RF_INTF_ACTIVATED_NTF.

 * Store the General Bytes of ATR_REQ.

 * Signal that Target mode is activated in case of an activation in NFC-DEP.

 * Update the NCI state accordingly.

 * Use the various constants defined in nfc.h.

 * Fix the ATR_REQ and ATR_RES maximum size. As per NCI 1.0 and NCI 1.1, the
   Activation Parameters for both Poll and Listen mode contain all the bytes of
   ATR_REQ/ATR_RES starting and including Byte 3 as defined in [DIGITAL].
   In [DIGITAL], the maximum size of ATR_REQ/ATR_RES is 64 bytes and they are
   numbered starting from Byte 1.
Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Send LA_SEL_INFO and LF_PROTOCOL_TYPE with NFC-DEP protocol enabled.
Configure 212 Kbit/s and 412 Kbit/s bit rates for Listen F.
Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Target mode protocols are given to the nci_start_poll() function
but were previously ignored.
To enable P2P Target, when NFC-DEP is requested as a Target mode protocol, add
NFC-A and NFC-F Passive Listen modes in RF_DISCOVER_CMD command.
Signed-off-by: NJulien Lefrique <lefrique@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

list_for_each_entry_safe() is necessary if list objects are deleted from
the list while traversing it. Not the case here, so we can use the base
list_for_each_entry variant.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When an NFC-DEP target receives an ATN PDU, its
supposed to respond with a similar ATN PDU.
When the Target receives an I PDU with the PNI
one less than the current PNI and the last PDU
sent was an ATN PDU, the Target is to resend the
last non-ATN PDU that it has sent.  This is
described in section 14.12.3.4 of the NFC Digital
Protocol Spec.

The digital layer's NFC-DEP code doesn't implement
this so add that support.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When an NFC-DEP Initiator times out when waiting for
a DEP_RES from the Target, its supposed to send an
ATN to the Target.  The Target should respond to the
ATN with a similar ATN PDU and the Initiator can then
resend the last non-ATN PDU that it sent.  No more
than 'N(retry,atn)' are to be send where
2 <= 'N(retry,atn)' <= 5.  If the Initiator had just
sent a NACK PDU when the timeout occurred, it is to
continue sending NACKs until 'N(retry,nack)' NACKs
have been send.  This is described in section
14.12.5.6 of the NFC-DEP Digital Protocol Spec.

The digital layer's NFC-DEP code doesn't implement
this so add that support.

The value chosen for 'N(retry,atn)' is 2.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When an NFC-DEP Target receives a NACK PDU with
a PNI equal to 1 less than the current PNI, it
is supposed to re-send the last PDU.  This is
implied in section 14.12.5.4 of the NFC Digital
Protocol Spec.

The digital layer's NFC-DEP code doesn't implement
Target-side NACK handing so add it.  The last PDU
that was sent is saved in the 'nfc_digital_dev'
structure's 'saved_skb' member.  The skb will have
an additional reference taken to ensure that the skb
isn't freed when the driver performs a kfree_skb()
on the skb.  The length of the skb/PDU is also saved
so the length can be restored when re-sending the PDU
in the skb (the driver will perform an skb_pull() so
an skb_push() needs to be done to restore the skb's
data pointer/length).
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When an NFC-DEP Initiator receives a frame with
an incorrect CRC or with a parity error, and the
frame is at least 4 bytes long, its supposed to
send a NACK to the Target.  The Initiator can
send up to 'N(retry,nack)' consecutive NACKs
where 2 <= 'N(retry,nack)' <= 5.  When the limit
is exceeded, a PROTOCOL EXCEPTION is raised.
Any other type of transmission error is to be
ignored and the Initiator should continue
waiting for a new frame.  This is described
in section 14.12.5.4 of the NFC Digital Protocol
Spec.

The digital layer's NFC-DEP code doesn't implement
any of this so add it.  This support diverges from
the spec in two significant ways:

a) NACKs will be sent for ANY error reported by the
   driver except a timeout.  This is done because
   there is currently no way for the digital layer
   to distinguish a CRC or parity error from any
   other type of error reported by the driver.

b) All other errors will cause a PROTOCOL EXCEPTION
   even frames with CRC errors that are less than 4
   bytes.

The value chosen for 'N(retry,nack)' is 2.

Targets do not send NACK PDUs.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When the peer in an NFC-DEP exchange has a
packet to send that is larger than the local
maximum payload, it sets the 'MI' bit in the
'I' PDU.  This indicates that NFC-DEP chaining
is to occur.

When such a PDU is received, the local side
responds with an 'ACK' PDU and this continues
until the peer sends an 'I' PDU with the 'MI'
bit cleared.  This indicates that the chaining
sequence is complete and the entire packet has
been transferred.

Receiving chained PDUs is currently not supported
by the digital layer so add that support.  When a
chaining sequence is initiated by the peer, the
digital layer will allocate an skb large enough
to hold 8 maximum sized frame payloads.  The maximum
payload can range from 64 to 254 bytes so 8 * 254 =
2032 seems like a reasonable compromise between
potentially wasting memory and constantly reallocating
new, larger skbs.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When the NFC-DEP code is given a packet to send
that is larger than the peer's maximum payload,
its supposed to set the 'MI' bit in the 'I' PDU's
Protocol Frame Byte (PFB).  Setting this bit
indicates that NFC-DEP chaining is to occur.

When NFC-DEP chaining is progress, sender 'I' PDUs
are acknowledged with 'ACK' PDUs until the last 'I'
PDU in the chain (which has the 'MI' bit cleared)
is responded to with a normal 'I' PDU.  This can
occur while in Initiator mode or in Target mode.

Sender NFC-DEP chaining is currently not implemented
in the digital layer so add that support.  Unfortunately,
since sending a frame may require writing the CRC to the
end of the data, the relevant data part of the original
skb must be copied for each intermediate frame.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The maximum payload for NFC-DEP exchanges (i.e., the
number of bytes between SoD and EoD) is negotiated
using the ATR_REQ, ATR_RES, and PSL_REQ commands.
The valid maximum lengths are 64, 128, 192, and 254
bytes.

Currently, NFC-DEP code assumes that both sides are
always using 254 byte maximums and ignores attempts
by the peer to change it.  Instead, implement the
negotiation code, enforce the local maximum when
receiving data from the peer, and don't send payloads
that exceed the remote's maximum.  The default local
maximum is 254 bytes.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

NFC-DEP DEP_REQ and DEP_RES exchanges using 'I'
and 'ACK/NACK' PDUs have a sequence number called
the Packet Number Information (PNI).  The PNI
is incremented (modulo 4) after every DEP_REQ/
DEP_RES pair and should be verified by the digital
layer code.  That verification isn't always done,
though, so add code to make sure that it is done.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

According to chapter 14 of the NFC-DEP Digital
Protocol Spec., the NAD byte should never be
present in DEP_REQ or DEP_RES frames.  However,
this is not enforced so add that enforcement code.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When in Target mode, the Initiator specifies whether
subsequent DEP_REQ and DEP_RES frames will include
a DID byte by the value passed in the ATR_REQ.  If
the DID value in the ATR_REQ is '0' then no DID
byte will be included.  If the DID value is between
'1' and '14' then a DID byte containing the same
value must be included in subsequent DEP_REQ and
DEP_RES frames.  Any other DID value is invalid.
This is specified in sections 14.8.1.2 and 14.8.2.2
of the NFC Digital Protocol Spec.

Checking the DID value (if it should be there at all),
is not currently supported by the digital layer's
NFC-DEP code.  Add this support by remembering the
DID value in the ATR_REQ, checking the DID value of
received DEP_REQ frames (if it should be there at all),
and including the remembered DID value in DEP_RES
frames when appropriate.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When in Initiator mode, the digital layer's
NFC-DEP code always sets the Device ID (DID)
value in the ATR_REQ to '0'.  This means that
subsequent DEP_REQ and DEP_RES frames must
never include a DID byte.  This is specified
in sections 14.8.1.1 and 14.8.2.1 of the NFC
Digital Protocol Spec.

Currently, the digital layer's NFC-DEP code
doesn't enforce this rule so add code to ensure
that there is no DID byte in DEP_RES frames.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Rearrange some of the code in digital_in_recv_dep_res()
and digital_tg_recv_dep_req() so the initial code looks
similar.  The real reason is prepare the code for some
upcoming patches that require these changes.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When digital_in_send_cmd() or digital_tg_send_cmd()
fail, they do not free the skb that was passed to
them so the routine that allocated the skb should
free it.  Currently, there are several routines in
the NFC-DEP code that don't do this so make them.
Reviewed-by: NThierry Escande <thierry.escande@linux.intel.com>
Tested-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Check the queue mapping earlier, skb->queue_mapping is more likely than
skb->data to still be in d-cache.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Let the other listeners being notified when a new or del interface
command has been issued, thus reducing later necessary request to be in
sync with current context.
Signed-off-by: NTomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Replace NL80211_ATTR_IFACE_SOCKET_OWNER attribute with more generic
NL80211_ATTR_SOCKET_OWNER that can be used with other commands
that interface creation.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>