The axp288 pmic has a lot more volatile registers then we were
listing in axp288_volatile_ranges, fix this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add defines for the AXP288_POWER_REASON and AXP288_RT_BATT_V_H and
AXP288_RT_BATT_V_L and AXP288_BC_* registers. While at it also move the
AXP288_TS_ADC_H-AXP288_GP_ADC_L defines, which for some reason where
in a different place, together with the rest of the AXP288 specific
defines.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The adc-enable register for the axp288 is 0x82, not 0x84.
0x82 is already defined as AXP20X_ADC_EN1 and that is what the
axp288_adc driver is actually using, so simply drop the wrong
AXP288_PMIC_ADC_EN define.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The R in PEK_DBR stands for rising, so it should be mapped to
AXP288_IRQ_POKP where the last P stands for positive edge.

Likewise PEK_DBF should be mapped to the falling edge, aka the
_N_egative edge, so it should be mapped to AXP288_IRQ_POKN.

This fixes the inverted powerbutton status reporting by the
axp20x-pek driver.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The axp288 has the following irqs 2 times: VBUS_FALL, VBUS_RISE,
VBUS_OV. On boot / reset the enable flags for both the normal and alt
version of these irqs is set.

Since we were only listing the normal version in the axp288 regmap_irq
struct, we were never disabling the alt versions of these irqs.

Add the alt versions to the axp288 regmap_irq struct, so that these
get properly disabled.

Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The interrupt line of the entire family of axp2xx pmics is active-low,
for devicetree enumerated irqs, this is dealt with in the devicetree.

ACPI irq resources have a flag field for this too, I tried using this
on my CUBE iwork8 Air tablet, but it does not contain the right data.

The dstd shows the irq listed as either ActiveLow or ActiveHigh,
depending on the OSID variable, which seems to be set by the
"OS IMAGE ID" in the BIOS/EFI setup screen.

Since the acpi-resource info is no good, simply pass in IRQF_TRIGGER_LOW
on the axp288.

Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The documentation of axp20x_device_remove() have a typo and use
axp20x_device_probe() as name. This patch fix this typo.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This declaration has never been used and is likely some left over from
early prototypes of the code, just remove it.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The PRCM block on the A23 contains a message box like interface to
the registers for the analog path controls of the internal codec.

Add a sub-device for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Currently we leak a lot of things when tearing down the IRQs this patch
fixes this cleaning up both the IRQ mappings and the IRQ domain itself.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

We have arizona_map_irq we might as well use it rather than hard coding
it in several places.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-arm-iio-pwm-4.11', 'ib-mfd-input-4.11-1', 'ib-mfd-mtd-4.11' and 'ib-mfd-power-supply-4.11' into ibs-for-mfd-merged

Add switch to report tablet mode.
Signed-off-by: NGwendal Grignou <gwendal@chromium.org>
Signed-off-by: NEnric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

On some newer boards using mkbp we're hooking up non-matrix buttons and
switches to the EC but NOT to the main application processor.

Let's add kernel support to handle this.  Rather than creating a whole
new input driver, we'll continue to use cros_ec_keyb and just report the
new keys.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add the defines for the new buttons and switches connected to the CrosEC.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Timers IPs can be used to generate triggers for other IPs like
DAC or ADC.
Each trigger may result of timer internals signals like counter enable,
reset or edge, this configuration could be done through "master_mode"
device attribute.

Since triggers could be used by DAC or ADC their names are defined
in include/ nux/iio/timer/stm32-timer-trigger.h and is_stm32_iio_timer_trigger
function could be used to check if the trigger is valid or not.

"trgo" trigger have a "sampling_frequency" attribute which allow to configure
timer sampling frequency.

version 8:
- change kernel version from 4.10 to 4.11 in ABI documentation

version 7:
- remove all iio_device related code
- move driver into trigger directory

version 5:
- simplify tables of triggers
- only create an IIO device when needed

version 4:
- get triggers configuration from "reg" in DT
- add tables of triggers
- sampling frequency is enable/disable when writing in trigger
  sampling_frequency attribute
- no more use of interruptions

version 3:
- change compatible to "st,stm32-timer-trigger"
- fix attributes access right
- use string instead of int for master_mode and slave_mode
- document device attributes in sysfs-bus-iio-timer-stm32

version 2:
- keep only one compatible
- use st,input-triggers-names and st,output-triggers-names
  to know which triggers are accepted and/or create by the device
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Define bindings for STM32 timer trigger

version 8:
- reword "reg" parameter description

version 4:
- remove triggers enumeration from DT
- add reg parameter

version 3:
- change file name
- add cross reference with mfd bindings

version 2:
- only keep one compatible
- add DT parameters to set lists of the triggers:
  one list describe the triggers created by the device
  another one give the triggers accepted by the device
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This driver adds support for PWM driver on STM32 platform.
The SoC have multiple instances of the hardware IP and each
of them could have small differences: number of channels,
complementary output, auto reload register size...

version 9:
- fix commit message header
- remove one space MODULE_ALIAS

version 8:
- fix comments done by Thierry on version 7

version 6:
- change st,breakinput parameter to make it usuable for stm32f7 too.

version 4:
- detect at probe time hardware capabilities
- fix comments done on v2 and v3
- use PWM atomic ops

version 2:
- only keep one comptatible
- use DT parameters to discover hardware block configuration
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Define bindings for pwm-stm32

version 9:
- change commit message header

version 8:
- reword st,breakinput description.

version 6:
- change st,breakinput parameter format to make it usuable on stm32f7 too.

version 2:
- use parameters instead of compatible of handle the hardware configuration
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This hardware block could at used at same time for PWM generation
and IIO timers.
PWM and IIO timer configuration are mixed in the same registers
so we need a multi fonction driver to be able to share those registers.

version 7:
- rebase on v4.10-rc2

version 6:
- rename files to stm32-timers
- rename functions to stm32_timers_xxx

version 5:
- fix Lee comments about detect function
- add missing dependency on REGMAP_MMIO

version 4:
- add a function to detect Auto Reload Register (ARR) size
- rename the structure shared with other drivers

version 2:
- rename driver "stm32-gptimer" to be align with SoC documentation
- only keep one compatible
- use of_platform_populate() instead of devm_mfd_add_devices()
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add bindings information for STM32 Timers

version 6:
- rename stm32-gtimer to stm32-timers
- change compatible
- add description about the IPs

version 2:
- rename stm32-mfd-timer to stm32-gptimer
- only keep one compatible string
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

When the axp288_faul_gauge driver was originally merged, it was
merged with a dependency on some other driver providing platform
data for it.

However the battery-data-framework which should provide that data
never got merged, resulting in x86 tablets / laptops with an axp288
having no working battery monitor, as before this commit the driver
would simply return -ENODEV if there is no platform data.

This commit removes the dependency on the platform_data instead
checking that the firmware has initialized the fuel-gauge and
reading the info back from the pmic.

What is missing from the read-back info is the table to map raw adc
values to temperature, so this commit drops the temperature and
temperature limits properties. The min voltage, charge design and
model name info is also missing. Note that none of these are really
important for userspace to have.

All other functionality is preserved and actually made available
by this commit.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=88471Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

When the axp288_charger driver was originally merged, it was merged with
a dependency on some other driver providing platform data for it.

However the battery-data-framework which should provide that data never
got merged, so the axp288_charger as merged upstream has never worked,
its probe method simply always returns -ENODEV.

This commit removes the dependency on the platform_data instead reading
back the charging current and charging voltage that the firmware has set
and using those values as the maximum values the user may set.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Make charger_init_hw_regs propagate i2c errors, instead of only warning
about them and then ignoring them.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Intel Apollo Lake SoC exposes serial SPI flash through the LPC device. The
SPI flash host controller is not discoverable through PCI config cycles
because P2SB (function 0 of the device 13) is hidden by the BIOS. We unhide
the device briefly in order to read BAR 0 of the SPI host controller.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Many Intel CPUs including Haswell, Broadwell and Baytrail have SPI serial
flash host controller as part of the LPC device. This will populate an MFD
cell suitable for the SPI host controller driver if we know that the LPC
device has one.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add support for the SPI serial flash host controller found on many Intel
CPUs including Baytrail and Braswell. The SPI serial flash controller is
used to access BIOS and other platform specific information. By default the
driver exposes a single read-only MTD device but with a module parameter
"writeable=1" the MTD device can be made read-write which makes it possible
to upgrade BIOS directly from Linux.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:

    AS      arch/powerpc/kernel/misc_32.o
  arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]

This problem is evident after commit 989cea5c ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created.  That was with commit 9994a338 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").

The offending line does not make a lot of sense.  This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.

Thanks to Nicholas Piggin for suggesting this solution.

Fixes: 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The timer type simplifications caused a new gcc warning:

  drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
  drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
     elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));

despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.

The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.

Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull timer type cleanups from Thomas Gleixner:
 "This series does a tree wide cleanup of types related to
  timers/timekeeping.

   - Get rid of cycles_t and use a plain u64. The type is not really
     helpful and caused more confusion than clarity

   - Get rid of the ktime union. The union has become useless as we use
     the scalar nanoseconds storage unconditionally now. The 32bit
     timespec alike storage got removed due to the Y2038 limitations
     some time ago.

     That leaves the odd union access around for no reason. Clean it up.

  Both changes have been done with coccinelle and a small amount of
  manual mopping up"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ktime: Get rid of ktime_equal()
  ktime: Cleanup ktime_set() usage
  ktime: Get rid of the union
  clocksource: Use a plain u64 instead of cycle_t

Pull SMP hotplug notifier removal from Thomas Gleixner:
 "This is the final cleanup of the hotplug notifier infrastructure. The
  series has been reintgrated in the last two days because there came a
  new driver using the old infrastructure via the SCSI tree.

  Summary:

   - convert the last leftover drivers utilizing notifiers

   - fixup for a completely broken hotplug user

   - prevent setup of already used states

   - removal of the notifiers

   - treewide cleanup of hotplug state names

   - consolidation of state space

  There is a sphinx based documentation pending, but that needs review
  from the documentation folks"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/armada-xp: Consolidate hotplug state space
  irqchip/gic: Consolidate hotplug state space
  coresight/etm3/4x: Consolidate hotplug state space
  cpu/hotplug: Cleanup state names
  cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
  staging/lustre/libcfs: Convert to hotplug state machine
  scsi/bnx2i: Convert to hotplug state machine
  scsi/bnx2fc: Convert to hotplug state machine
  cpu/hotplug: Prevent overwriting of callbacks
  x86/msr: Remove bogus cleanup from the error path
  bus: arm-ccn: Prevent hotplug callback leak
  perf/x86/intel/cstate: Prevent hotplug callback leak
  ARM/imx/mmcd: Fix broken cpu hotplug handling
  scsi: qedi: Convert to hotplug state machine

Pull turbostat updates from Len Brown.

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: remove obsolete -M, -m, -C, -c options
  tools/power turbostat: Make extensible via the --add parameter
  tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
  tools/power turbostat: line up headers when -M is used
  tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
  tools/power turbostat: Support Knights Mill (KNM)
  tools/power turbostat: Display HWP OOB status
  tools/power turbostat: fix Denverton BCLK
  tools/power turbostat: use intel-family.h model strings
  tools/power/turbostat: Add Denverton RAPL support
  tools/power/turbostat: Add Denverton support
  tools/power/turbostat: split core MSR support into status + limit
  tools/power turbostat: fix error case overflow read of slm_freq_table[]
  tools/power turbostat: Allocate correct amount of fd and irq entries
  tools/power turbostat: switch to tab delimited output
  tools/power turbostat: Gracefully handle ACPI S3
  tools/power turbostat: tidy up output on Joule counter overflow

Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.

This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.

The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).

This improves the performance of page lock intensive microbenchmarks by
2-3%.

Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A page is not added to the swap cache without being swap backed,
so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Acked-by: NHugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.

Get rid of the union and just keep ktime_t as simple typedef of type s64.

The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

There is no point in having an extra type for extra confusion. u64 is
unambiguous.

Conversion was done with the following coccinelle script:

@rem@
@@
-typedef u64 cycle_t;

@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>