Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of link flap avoidance between PXE boot and bnx2x, set the appropriate
PHY DEVAD even if LFA kicks in.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 1G KR link by restoring CL72 misc control register to default value rather
than 0.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the bnx2x and cnic drivers into using FW 7.8.2
which was recently submitted into the linux-firmware tree.

A short summary of minor bugs fixed by this FW:
 1. In switch dependent mode, fix several issues regarding inner vlan
    vs. DCB priorities.
 2. iSCSI - not all packets were completed on a forward channel.
 3. DCB - fixed for 4-port devices.
 4. Fixed false parity reported in CAM memories when operating near -5%
    on the 1.0V core supply.
 5. ETS default settings are set to fairness between traffic classes
    (rather than strict priority), and uses the same chip receive buffer
    configuration for both PFC and pause.

For a complete list of fixes made by this FW, see commit 236367db
in the linux-firmware git repository.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prior to this fix, the driver reported the chip's active duplex state
is always 'full', even if using half-duplex mode.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Various flows in the bnx2x driver cause a link-flap - if the link
is up, it would be toggled down (after a mac/phy reset) and then
taken back up.

In many of these cases, there is no need to do cause such a flap,
as the associated flows should not actually affect the link.

This patch adds the 'Link Flap Avoidance' mechanism, which allows
the driver to better determine if a given flow requires a link change,
and thus minimize the number of link flaps caused by the driver.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate the interrupt setting part of each external PHY to a specific
function.
This allows calling the interrupt setting in case of link-flap avoidance,
since some link owners may not enable the interrupt on their own.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables boards with 54618SE phys and a sufficiently new
firmware to use native EEE instead of auto-greeen.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to lay the foundation for 1G EEE support, several segments of code
which are common to both 1G and 10G EEE configurations were extracted from
the 10G EEE configuration flow to their own functions.
E.g., bnx2x_eee_initial_config, bnx2x_eee_advertise, bnx2x_eee_disable, etc.

The rest of the EEE functions were relocated and placed in a single,
continuous section of the file.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent functions from disabling EEE to other functions using other ports.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch aligns the EEE status with that of all other link properties,
by changing the way its accessed - instead of a direct read to the shared
memory, each function maintain its own copy locally.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 57840 boards come in two flavours: 2 x 20G and 4 x 10G.
To better differentiate between the two flavours, a separate device ID
was assigned to each.
The silicon default value is still the currently supported 57840 device ID
(0x168d), and since a user can damage the nvram (e.g., 'ethtool -E')
the driver will still support this device ID to allow the user to amend the
nvram back into a supported configuration.

Notice this patch contains lines longer than 80 characters (strings).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the ethtool functionality of accessing optic modules'
information and eeprom to the bnx2x driver.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Automatically lower requested link speed to 1G in case 1G SFP+
module is detected.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a semantic change, cleaning some sections in which the bnx2x
handles the phy's registers.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does several things:
 1. Add static to function when possible.
 2. Correct comments.
 3. Change msleep(small) --> usleep_range(small, small*2).
    Also correct existing calls to usleep_range.
 4. Remove dead code.
 5. Change 'if(rc != 0)' --> if(rc)

Most of these changes are purely semantic.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds the ability to identify sfp+ modules' Tx fault, and when such
occur shut down the link.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c8c60d88 contained
an incorrect logic which enabled a buffer overflow when accessing
an array during LPI pass-through configuration.
This patch fixes this issue by removing that logic altogether.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I2C is not responding it's usually due to a previous
unexpected reset during I2C operation. We release it by
powering down and up the SFP+ module.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds energy efficient energy support (802.3az) to bnx2x
boards with 84833 phys (and sufficiently new BC and external FW).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch adds afex multifunction support to the driver (afex
multifunction is based on vntag header) and updates FW version used to 7.2.51.

Support includes the following:

1. Configure vif parameters in firmware (default vlan, vif id, default
   priority, allowed priorities) according to values received from NIC.
2. Configure FW to strip/add default vlan according to afex vlan mode.
3. Notify link up to OS only after vif is fully initialized.
4. Support vif list set/get requests and configure FW accordingly.
5. Supply afex statistics upon request from NIC.
6. Special handling to L2 interface in case of FCoE vif.
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sp_pri_to_cos[] array size depends on the config but lets say it is
BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also
DCBX_E3B0_MAX_NUM_COS_PORT0.  In the original code
"pri == max_num_of_cos" was accepted but it is one past the end of the
array.

Also we used "pri" before capping it.  It's a harmless read past the end
of the array, but it would affect which error message gets printed.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch clears a warning message of "MDC/MDIO access timeout" which may
appear when interface is loaded due to missing clock setting before resetting
the LED, and starting periodic function too early.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a link problem on the second port of BCM57711 + BCM84823 boards due to
incorrect macro usage.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX
laser is controller by GPIO, after 1.60.xx drivers were previously loaded.
On these designs the TX_LASER is enabled by logic AND between the PHY
(through MDIO), and the GPIO. When an old driver is used, it disables the
MDIO part, hence the GPIO control had no affect de facto.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix no-LED problem when link speed is 1G on BCM57712 + BCM8727 designs, by
removing a logic error checking for a different PHY.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 578x0-SFI pre-emphasis settings per HW recommendations to achieve better
link strength.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM57810-KR link may not come up in 1G after running loopback test, so set
the relevant registers to their default values before starting KR autoneg.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 57810-KR flow-control handling link is achieved via CL37 AN.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a problem in which PFC frames are not honored, due to incorrect link
attributes synchronization following PMF migration, and verify PFC XON is not
stuck from previous link change.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A semantic patch, fixing style issues in the bnx2x's link code.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restore remote-faule detection, which periodically checks for
remote-fault on the MAC layer. In case physical link appear to be
up but fault is set, it will provide a link down indication, and
when the fault is cleared, it will indicate link up again.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flow in which the bnx2x driver starts after a previous driver
has been terminated in an 'unclean' manner has several bugs and
FW risks, which makes it possible for the driver to fail after
boot-from-SAN or kdump.
This patch contains a revised flow which performs a safer
initialization, solving the possible crash scenarios.
Notice this patch contains lines with over 80 characters, as it
keeps print-strings in a single line.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy FW version is stored in regular memory, no MDC-MDIO access or
any special locks are required to read it in the current implementation.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>