We need to release_firmware() in order not to leak memory.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NPekka Enberg <penberg@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the case of alloc_netdev_mq failure and kmalloc failure,
current implementation returns ERR_PTR(0).

As a result, the caller of iwm_if_alloc does not catch the error by IS_ERR
macro. Fix it by setting proper error code for ret variable in the failure
cases.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

pcmcia_request_irq() and pcmcia_enable_device() are intended
to be called from process context (first function allocate memory
with GFP_KERNEL, second take a mutex). We can not take spin lock
and call them.

It's safe to move spin lock after pcmcia_enable_device() as we
still hold off IRQ until dev->base_addr is 0 and driver will
not proceed with interrupts when is not ready.

Patch resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=643758

Reported-and-tested-by: rbugz@biobind.com
Cc: stable@kernel.org  # 2.6.34+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is an attempt to fix a long standing open bug:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334

The interrupt handler checks for INTA being -1, apparently that means that the
hardware is gone. But the interrupt handler defers actual interrupt processing
to a tasklet. By the time the tasklet is run and checks INTA again, the
hardware might be gone and INTA be -1, which confuses the driver because all
event bits are set.

The patch applies to 2.6.37.
Signed-off-by: NIndan Zupancic <indan@nul.nu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some Broadcom based wireless devices contain dangling ethernet cores.
This triggers the ssb probing mechanism and tries to load the b44 driver
on this core.
Ignore the dangling core in the ssb core scanning code to avoid
access to the core and failure of b44 probing.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."

Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.

Yup, it's the exact opposite!

Cc: <stable@kernel.org>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Just create a section to collect the LED trigger
functions and add a very short description as to
what drivers should do.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some mesh attribute/command docs are missing or
have errors in the name so they don't match, fix
all of them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When I made the patch to add mesh join/leave I
didn't pay attention to docs because it was a
proof of concept, and then when we actually did
merge it I forgot -- add docs now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The flag is IEEE80211_TX_CTL_TX_OFFCHAN and I had
added that in a previous patch but forgotten docs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add documentation for the new callbacks that I
forgot in the patch adding the callbacks.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.

Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

USB devices do not require the chip test routine.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change fixes several issues found in ntuple filtering while I was
doing the ATR refactor.

Specifically I updated the masks to work correctly with the latest version
of ethtool, I cleaned up the exception handling and added detailed error
output when a filter is rejected, and corrected several bits that were set
incorrectly in ixgbe_type.h.

The previous version of this patch included a printk that was left over from
me fixing the filter setup.  This patch does not include that printk.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change adds a compressed input type for atr signature hash
computation.  It also drops the use of the set functions when setting up
the ATR input since we can then directly setup the hash input as two dwords
that can be stored and passed as registers.

With these changes the cost of computing the has is low enough that we can
perform a hash computation on each TCP SYN flagged packet allowing us to
drop the number of flow director misses considerably in tests such as
netperf TCP_CRR.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change cleans up the layout of the flow director data, and the
algorithm used to calculate the hash resulting in a 35x / 3500% performance
increase versus the old flow director hash computation.  The overall effect
is only a 1% increase in transactions per second though due to the fact
that only 1 packet in 20 are actually hashed upon.

TCP_RR before:
Socket Size   Request  Resp.   Elapsed  Trans.
Send   Recv   Size     Size    Time     Rate
bytes  Bytes  bytes    bytes   secs.    per sec

16384  87380  1        1       60.00    23059.27
16384  87380

TCP_RR after:
Socket Size   Request  Resp.   Elapsed  Trans.
Send   Recv   Size     Size    Time     Rate
bytes  Bytes  bytes    bytes   secs.    per sec

16384  87380  1        1       60.00    23239.98
16384  87380
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When disable the Rx logic globally, we would also want to disable the per Rx
queue receive logic by per queue Rx control register RXDCTL so no more DMA is
happening from the packet buffer to the receive buffer associated with the Rx
ring, before we start unmapping Rx ring receive buffer. The hardware may take
max of 100us before the corresponding Rx queue is really disabled. Added
ixgbe_disable_rx_queue() for this purpose.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the gigabit phys present on the CE4100 reference
platforms.
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82574 needs to configure Low Power Link Up (or LPLU) differently than
the other parts in the 8257x family supported by the driver.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Phys supported by the driver do not remain powered off across a reset
of the device when the interface is down, e.g. on 82571, but not on 82574.
This patch powers down (only when WoL is disabled) the PHY after a reset if
the interface is down and the ethtool diagnostics are not currently running.

The ethtool diagnostic function required a minor re-factor as a result, and
the e1000_[get|put]_hw_control() functions are renamed since they are no
longer static to netdev.c as they are needed by the ethtool diagnostics.
A couple minor whitespace issues were cleaned up, too.
Reported-by: NArthur Jones <ajones@riverbed.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the 82579 jumbo frame workaround, there is no need to re-write the CRC
calculation functionality already found in the kernel's ether_crc_le().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use string functions with bounds checking rather than their non-bounds
checking counterparts, and do not hard code these boundaries.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants.  Fix
a couple whitespace issue with two already existing calls to e1e_wphy.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ICR register is clear on read and we don't care what the returned value
is when resetting the hardware so the icr variable(s) can be removed.  We
should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and
from e1000_get_phy_id_82571() (dump a debug message when it fails and when
an unknown Phy id is returned).
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to compute the features for other offloads (primarily
scatter/gather), we need to first check the ability of the NIC to
offload the checksum for the packet.  Since we have already computed
this, we can directly use the result instead of figuring it out
again.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This switches skb_need_linearize() to use the features that have
been centrally computed.  In doing so, this fixes a problem where
scatter/gather should not be used because the card does not support
checksum offloading on that type of packet.  On device registration
we only check that some form of checksum offloading is available if
scatter/gatther is enabled but we must also check at transmission
time.  Examples of this include IPv6 or vlan packets on a NIC that
only supports IPv4 offloading.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This switches dev_gso_segment() to use the device features computed
by the centralized routine.  In doing so, it fixes a problem where
it would always use dev->features, instead of those appropriate
to the number of vlan tags if any are present.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that there is a single function that can compute the device
features relevant to a packet, we don't want to run it for each
offload.  This converts netif_needs_gso() to take the features
of the device, rather than computing them itself.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_get_vlan_features() is currently only used by netif_needs_gso(),
so it only concerns itself with GSO features.  However, several other
places also should take into account the contents of the packet when
deciding whether to offload to hardware.  This generalizes the function
to return features about all of the various forms of offloading.  Since
offloads tend to be linked together, this avoids duplicating the logic
in each location (i.e. the scatter/gather code also needs the checksum
logic).
Suggested-by: NMichał Mirosław <mirqus@gmail.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently only have software fallback for one type of checksum: the
TCP/UDP one's complement.  This means that a protocol that uses hardware
offloading for a different type of checksum (FCoE, SCTP) must directly
check the device's features and do the right thing ahead of time.  By
the time we get to dev_can_checksum(), we're only deciding whether to
apply the one algorithm in software or hardware.  NETIF_F_HW_CSUM has the
same capabilities as the software version, so we should always use it if
present.  The primary advantage of this is multiply tagged vlans can use
hardware checksumming.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It workarounds the 60s firmware load failure timeout for the
non-modular case.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix new kernel-doc notation warning in net/core/filter.c:

Warning(net/core/filter.c:172): No description found for parameter 'fentry'
Warning(net/core/filter.c:172): Excess function parameter 'filter' description in 'sk_run_filter'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix new kernel-doc notation warning in sock.h by annotating skc_dontcopy_*
as private fields.

Warning(include/net/sock.h:163): No description found for parameter 'skc_dontcopy_end[0]'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to NLM_F_DUMP is composed of two bits, NLM_F_ROOT | NLM_F_MATCH,
when doing "if (x & NLM_F_DUMP)", it tests for _either_ of the bits
being set. Because NLM_F_MATCH's value overlaps with NLM_F_EXCL,
non-dump requests with NLM_F_EXCL set are mistaken as dump requests.

Substitute the condition to test for _all_ bits being set.
Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The forcedeth driver uses the legacy PCI power management, so it has
to do PCI-specific things in its ->suspend() and ->resume() callbacks
and some of them are not done correctly.

Convert forcedeth to the new PCI power management framework and make
it let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.

Tested with nVidia Corporation MCP55 Ethernet (rev a2).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This converts sky2 to new VLAN offload flags control via ethtool.
It also allows for transmit offload of vlan tagged frames which
was not possible before.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>