Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

If we detach due to local read-error (which sets a bit in the bitmap),
stay Primary, and then re-attach (which re-reads the bitmap from disk),
we potentially lost the "out-of-sync" (or, "bad block") information in
the bitmap.

Always (try to) write out the changed bitmap pages before going diskless.

That way, we don't lose the bit for the bad block,
the next resync will fetch it from the peer, and rewrite
it locally, which may result in block reallocation in some
lower layer (or the hardware), and thereby "heal" the bad blocks.

If the bitmap writeout errors out as well, we will (again: try to)
mark the "we need a full sync" bit in our super block,
if it was a READ error; writes are covered by the activity log already.

If that superblock does not make it to disk either, we are sorry.

Maybe we just lost an entire disk or controller (or iSCSI connection),
and there actually are no bad blocks at all, so we don't need to
re-fetch from the peer, there is no "auto-healing" necessary.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

 - struct drbd_conf { ... unsigned long flags; ... }
 + struct drbd_conf { ... unsigned long drbd_flags[N]; ... }

And introduce wrapper functions for test/set/clear bit operations
on this member.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The intention of force-detach is to be able to deal with a completely
unresponsive lower level IO stack, which does not even deliver error
completions anymore, but no completion at all.

In all other cases, we must still wait for the meta data IO completion.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

This has not yet been observed, but conceivably, when using GFP_KERNEL
allocations from drbd_md_sync(), drbd_flush_after_epoch() or
receive_SyncParam(), we could trigger additional IO to our own device,
or an other device in a criss-cross setup, and end up in a local
deadlock, or potentially a distributed deadlock in a criss-cross setup
involving the peer blocked in a similar way waiting for us to make
progress.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The former comment arguing that GFP_KERNEL was good enough was wrong: it
did not take resize into account at all, and assumed the only path
leading here was the normal attach on a still secondary device, so no
deadlock would be possible.

Both resize on a Primary, or attach on a diskless Primary,
could potentially deadlock.

drbd_bm_resize() is called while IO to the respective device is
suspended, so we must use GFP_NOIO to avoid potential deadlock.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

"aborting" requests, or force-detaching the disk, is intended for
completely blocked/hung local backing devices which do no longer
complete requests at all, not even do error completions.  In this
situation, usually a hard-reset and failover is the only way out.

By "aborting", basically faking a local error-completion,
we allow for a more graceful swichover by cleanly migrating services.
Still the affected node has to be rebooted "soon".

By completing these requests, we allow the upper layers to re-use
the associated data pages.

If later the local backing device "recovers", and now DMAs some data
from disk into the original request pages, in the best case it will
just put random data into unused pages; but typically it will corrupt
meanwhile completely unrelated data, causing all sorts of damage.

Which means delayed successful completion,
especially for READ requests,
is a reason to panic().

We assume that a delayed *error* completion is OK,
though we still will complain noisily about it.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Disconnecting is a cluster wide state change. In case the peer node agrees
to the state transition, it sends back the fact on the meta-data connection
and closes both sockets.

In case the node node that initiated the state transfer sees the closing
action on the data-socket, before the P_STATE_CHG_REPLY packet, it was
going into one of the network failure states.

At least with the fencing option set to something else thatn "dont-care",
the unclean shutdown of the connection causes a short IO freeze or
a fence operation.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The DISCARD_CONCURRENT flag should be set on one node and cleared on the
other node.
As the code was before it was theoretical possible that a node accepts the
meta socket, but has to close it later on, and keeps the DISCARD_CONCURRENT
flag.
Correct this by moving the clear_bit(DISCARD_CONCURRENT) where the packet
gets sent.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

We now can schedule only a specific range of sectors for online verify,
or interrupt a running verify without interrupting the connection.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

There is at least the worker context, the receiver context, the context of
receiving netlink packts and processes reading a sysfs attribute that access
the uuids.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Arbitrarily selecting GPIOLIB causes trouble on some architectures,
so don't do that. Instead, just make the optional multiplexing code
depend on CONFIG_I2C_MUX_GPIO instead of CONFIG_I2C_MUX for now. We
can revisit if the i2c-i801 driver ever supports other multiplexing
flavors.

Also make that optional code depend on DMI, as it won't do anything
without that.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>

Move the i2c-stub driver to drivers/i2c, to match the Kconfig entry.
This is less confusing that way.

I also fixed all checkpatch warnings and errors.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <peterhuewe@gmx.de>

This change correctly computes the header length and data length in
the fragments to avoid a bug where we would end up with extremely
slow performance.  Also adopt use of skb_frag_size() accessor.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org [v3.6]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These devices provide QMI and ethernet functionality via a standard CDC
ethernet descriptor.  But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface.  Thus blacklist the devices in cdc_ether and add their IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver anchors the tx urbs and defers the urb submission if
a transmit request comes when the interface is suspended.
Anchoring urb increments the urb reference count. These
deferred urbs are later accessed by calling usb_get_from_anchor()
for submission during interface resume. usb_get_from_anchor()
unanchors the urb but urb reference count remains same.
This causes the urb reference count to remain non-zero
after usb_free_urb() gets called and urb never gets freed.
Hence call usb_put_urb() after anchoring the urb to properly
balance the reference count for these deferred urbs. Also,
unanchor these deferred urbs during disconnect, to free them
up.
Signed-off-by: NHemant Kumar <hemantk@codeaurora.org>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a failure takes place during the EQ creation, we need to unmap the
UAR memory block too.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NUri Habusha <urih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan tag can be zero. This is why it can't serve as an indication
that packet requires VLAN header in the TX flow.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).

Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The delayed work function int_in_work() may call usb_reset_device()
and thus, indirectly, the driver's pre_reset method. Trying to
cancel the work synchronously in that situation would deadlock.
Fix by avoiding cancel_work_sync() in the pre_reset method.

If the reset was NOT initiated by int_in_work() this might cause
int_in_work() to run after the post_reset method, with urb_int_in
already resubmitted, so handle that case gracefully.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We handle NOTIFY_THROTTLING so don't then fall through to unsupported event.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Decode multitouch reports from the touch sensor of the Cintiq 24HD
touch.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Like our other pen-and-touch products, the Cintiq 24HD touch needs data
to be shared between its two sensors to facilitate proximity-based palm
rejection.

Unlike other tablets that report sensor data through separate interfaces
of the same USB device, the Cintiq 24HD touch has separate USB devices
that are connected to an internal USB hub.

This patch makes it possible to designate the USB VID/PID of the other
device so that the two may share data.  To ensure we don't accidentally
link to a sensor from a physically separate device (if several have been
plugged in), we limit the search to siblings (i.e., devices directly
connected to the same hub).
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Tested-by: NRoland Stigge <stigge@antcom.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The dw_dmac driver was originally developed for avr32 to be used with the
Synopsys DesignWare AHB DMA controller.  Starting from 2.6.38, access to
the device's i/o memory was done with the little-endian readl/writel
functions(1)

This broke the driver for the avr32 platform, because it needs big
(native) endian accessors.  This patch makes the endianness configurable
using 'DW_DMAC_BIG_ENDIAN_IO', which will default be true for AVR32

I submitted this patch before(2) but then waited for Andy to finish other
changes to the same module(3).

(1) https://patchwork.kernel.org/patch/608211
(2) https://lkml.org/lkml/2012/8/26/148
(3) https://lkml.org/lkml/2012/9/21/173Signed-off-by: NHein Tibosch <hein_tibosch@yahoo.es>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Havard Skinnemoen <havard@skinnemoen.net>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add this missing SPI dependency and prevent the driver from building
without SPI, because functions of the spi driver are used in this
driver.

  drivers/video/backlight/ili9320.c:51: undefined reference to `spi_sync'

Also, a prompt string for CONFIG_LCD_ILI9320 is added for explicit
selection.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the variable ep_ctx from xhci_add_endpoint(), since it is
assigned but unused.  Caught by Coverity.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Remove the variable slot_ctx from xhci_dbg_ctx(), since it is assigned
but unused.  Caught by Coverity.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Coverity complains that xhci_evaluate_context_result() is missing a
break statement after the COMP_EBADSLT switch case.  It's not a big
deal, since we wanted to return the same error code as the case
statement below it does.  The end result would be one that a Slot
Disabled error completion code would also print the warning message
associated with a Context State error code.  No other bad behavior would
result.

It's not worth backporting to stable kernels, since it only fixes an
issue with too much debugging.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The command cancellation code doesn't check whether find_trb_seg()
couldn't find the segment that contains the TRB to be canceled.  This
could cause a NULL pointer deference later in the function when next_trb
is called.  It's unlikely to happen unless something is wrong with the
command ring pointers, so add some debugging in case it happens.

This patch should be backported to stable kernels as old as 3.0, that
contain the commit b63f4053 "xHCI:
handle command after aborting the command ring".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This will fix warnings like following when CONFIG_PM_SLEEP is not set:

        warning: 'xxx_suspend' defined but not used [-Wunused-function]
        warning: 'xxx_resume' defined but not used [-Wunused-function]

Because
	SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)

Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).

Cc: Mattia Dongili <malattia@linux.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Board name changed on another shipping Lucid tablet.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Cc: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

BIOS vendors keep changing the BIOS versions. Only match the beginning
of the string to match all Lucid tablets with board name M11JB.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Cc: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove temporary do-while(0) loop used to keep changes minimal.

Fixup indentation, remove some line breaks, and replace break with goto
to maintain flow.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the indentation was kept intact using a do-while(0) in order
to facilitate review. A follow-up patch will remove it.

Compile-only tested.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove private zombie flag used to signal disconnect and to prevent
control urb from being submitted from interrupt urb completion handler.

The control urb will not be re-submitted as both the control urb and the
interrupt urb is killed on disconnect.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The private int_urb is never allocated so the submission from the
control completion handler will always fail. Remove this odd piece of
broken code.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>