Multichannel and DFS cannot be supported at same time. So when multichannel
operation is enabled by module parameter, we enable number of channel as 2
while registering wiphy. For all other cases we advertise DFS support to
cfg80211. Patch also adds support for radar detect widths parameter.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to advetise mwifiex multichannel support to
cfg80211. If module parameter drcs is enabled and FW supports multichannel
operation we advertise this support to cfg80211. As of now 2 simultaneous
channels are supported.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for setting multichannel policy as module parameter
to FW. Value of 1 indicates Multichannel support is enabled
and value of 0 disables it.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to extend TX Data pause for AP intefaces.
Also for station role, support for pausing/unpausing all traffic
when mac address parameter is BSSID is added.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to enable data traffic only when port is open.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for another TX queue in driver- bypass
TX queue. This queue is used for sending data/mgmt packets while
in disconnected state i.e. when port is yet not unblocked.
TDLS setup packets would also be queued in this queue.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap. Also we configure 11D
settings info FW only for specific band. So we need to download domain
info to FW even if domain remains unchanged but band is changed.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add cfg80211 tdls_chan_switch and tdls_cancel_chan_switch
handler.
With this handlers, mwifiex would support TDLS channel switch feature.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TDLS link status - channel switching, off channel or base channel itself
indicates that TDLS link is setup.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch enable tdls channel switch ext capability in tdls action
frame, and also configure basic tdls channel switch parameters while
tdls setup completed and tdls link is enabled..
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add support for a new tdls configuration command
which is used for configuration of tdls channel switch parameters.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add support for tdls channel switch event process.
We block TX queues for particular RA list depending upon channel
switch state. If channel switch state is moving to base channel,
we unblock RA lists for AP. If channel switch state is moving to off
channel, we unblock TDLS peer RA lists.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add new tdls status used for tdls channel switch.
Driver in turn would block cmd path and data path if tdls
channel switching. Data path to non tdls peer should be blocked
if tdls channel switch to off-channel.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If tx_pkts_queued is increased for tx paused receive address, tx process
will be triggered for this packet. But since RA list was tx paused,
there will be an infinite loop in mwifiex_wmm_process_tx waiting for the
event(tx pause, tdls cs) to cancel tx pause. This will be an dead loop,
since main_process was locked at this time, there will be no opportunity
to process event.

So do not increase tx_pkts_queued if receive address tx paused,
this will be restored RA list is unpaused.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Data traffic to tx paused receive address should be blocked.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to enable TX data pause feature for mwifiex.
Whenever FW TX buffers reach threshold, FW would send TX pause event
to driver. Driver in turn would block data traffic to that particular
receiver address.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds missing break statement at the end of
EVENT_BT_COEX_WLAN_PARA_CHANGE switch section.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If timeshare coexistance between bluetooth and WLAN gets enabled,
firmware will give host an event to reduce Rx AMPDU BA window size.
The event is handled in this patch.
Signed-off-by: NChunfan Chen <jeffc@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes semantic warning for debugging data dump feature.
Previous code is based on the assumption that skb is not null.
New change makes sure that we already have data buffer.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Negative adapter->tx_pending is observed while running data traffic,
because tx_pending is decreased once more for AMSDU packet.

since tx_pending have been decreased for all the source MSDU packets,
we don't need to update once more for AMSDU packet.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes issue with the accessing correct ra_list by
downgrading corresponding tid number.

Alternatively, ra lists are created in mwifiex_wmm_add_buf_txqueue
using downgraded tid number.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This was missing and would cause issue in WMM handling.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This would enable driver to enter powersave as soon as connected.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We often see ADDBA request packets coming to driver because driver
has registered for action frame subtype. We dont process BA action
frames in host; drop such frames.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NXinmin Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Earlier only RSN, WPA and channel switch IEs from tail buffer would
be downloaded to FW.
This patch adds support for downloading more IEs from tail buffer.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to parse power constraint IEs from
Tail buffer. This power constraint is then set to FW during
bss_config download.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch extend cfg80211 dump_station handler, support for
dump stations associated to mwifiex micro AP.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add sta_list firmware command, which can be used
to get power status and rssi for the stations associated to
mwifiex micro AP.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to disable ongoing CAC in FW upon
detecting radar during CAC period.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes an issue where we were still setting 11h_active
flag to true for channel defs where DFS is not required.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

BSS reset would reset all state information in FW.
Issue 11d config command after reset to enabled 11d in FW.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This would enable clearing of FW bss data structures when AP
operations are stopped.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Correct bss_type assignment in add_virtual_interface.
This would ensure correct operation in multiple station scenarios.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds more detailed information about association failures
 - reason and states.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently device dump generated in the driver is retrieved
using ethtool set/get dump commands. We will get rid of
ethtool approach and use devcoredump framework.

Device dump can be trigger by
cat /debugfs/mwifiex/mlanX/device_dump
and when the dump operation is completed, data can be read by
cat /sys/class/devcoredump/devcdX/data

We have prepared following script to split device dump data
into multiple files.

 [root]# cat mwifiex_split_dump_data.sh
 #!/bin/bash
 # usage: ./mwifiex_split_dump_data.sh dump_data

 fw_dump_data=$1

 mem_type="driverinfo ITCM DTCM SQRAM APU CIU ICU MAC"

 for name in ${mem_type[@]}
 do
     sed -n "/Start dump $name/,/End dump/p" $fw_dump_data  > tmp.$name.log
     if [ ! -s tmp.$name.log ]
     then
         rm -rf tmp.$name.log
     else
         #Remove the describle info "Start dump" and "End dump"
         sed '1d' tmp.$name.log | sed '$d' > /data/$name.log
         if [ -s /data/$name.log ]
         then
             echo "generate /data/$name.log"
         else
             sed '1d' tmp.$name.log | sed '$d' > /var/$name.log
             echo "generate /var/$name.log"
         fi
         rm -rf tmp.$name.log
     fi
 done
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently we are dumping driver information also inside
firmware dump API. We will call it as device dump and
dump driver and firmware data separately.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Small letters are used in debug messages to match coding style
at other places.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>