A recent change to reduce delay granularity waiting for firmware
reponse has caused a regression.  With a tighter delay loop,
the driver may see the beginning part of the response faster.
The original 5 usec delay to wait for the rest of the message
is not long enough and some messages are detected as invalid.

Increase the maximum wait time from 5 usec to 20 usec.  Also, fix
the debug message that shows the total delay time for the response
when the message times out.  With the new logic, the delay time
is not fixed per iteration of the loop, so we define a macro to
show the total delay time.

Fixes: 9751e8e7 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds PCI device IDs to support 25GE and 100GE card:

1. Add device id 0x0201 for HINIC 100GE dual port card.
2. Add device id 0x0200 for HINIC 25GE dual port card.
3. Macro of device id 0x1822 is modified for HINIC 25GE quad port card.
Signed-off-by: NZhao Chen <zhaochen6@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change fixes a couple of type mismatch reported by the sparse
tool, explicitly using the requested type for the offending arguments.
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the core networking needs to detect the transport offset in a given
packet and parse it explicitly, a full-blown flow_keys struct is used for
storage.
This patch introduces a smaller keys store, rework the basic flow dissect
helper to use it, and apply this new helper where possible - namely in
skb_probe_transport_header(). The used flow dissector data structures
are renamed to match more closely the new role.

The above gives ~50% performance improvement in micro benchmarking around
skb_probe_transport_header() and ~30% around eth_get_headlen(), mostly due
to the smaller memset. Small, but measurable improvement is measured also
in macro benchmarking.

v1 -> v2: use the new helper in eth_get_headlen() and skb_get_poff(),
  as per DaveM suggestion
Suggested-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minor conflict in ip_output.c, overlapping changes to
the body of an if() statement.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
net/ipv6 misc

This patchset contains two patches for net/ipv6.

Patch 1 is a trivial typo fix in documentation.
Patch 2 by Eran is a re-spin. It adds GRO support for IPv6 GRE tunnel,
this significantly improves performance in case GRO in native interface
is disabled.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add GRO capability for IPv6 GRE tunnel and ip6erspan tap, via gro_cells
infrastructure.

Performance testing: 55% higher badwidth.
Measuring bandwidth of 1 thread IPv4 TCP traffic over IPv6 GRE tunnel
while GRO on the physical interface is disabled.
CPU: Intel Xeon E312xx (Sandy Bridge)
NIC: Mellanox Technologies MT27700 Family [ConnectX-4]
Before (GRO not working in tunnel) : 2.47 Gbits/sec
After  (GRO working in tunnel)     : 3.85 Gbits/sec
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 'an' into 'and', and use a comma instead of a period.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed*: Add support for new multi partitioning modes.

The patch series simplifies the multi function (MF) mode implementation of
qed/qede drivers, and adds support for new MF modes.

Please consider applying it to net-next branch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds support for new Multi function mode wherein the traffic
classification is done based on the 802.1ad tagging and the outer vlan tag
provided by the management firmware.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The data member 'is_mf_default' is not used by the qed/qede drivers,
removing the same.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The v9fs_get_trans_by_name(char *s) variable name is not "name" but "s".
Signed-off-by: NSun Lianwen <sunlw.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan_flags enum is defined in include/uapi/linux/if_vlan.h file.
not in include/linux/if_vlan.h file.
Signed-off-by: NSun Lianwen <sunlw.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minor conflict, a CHECK was placed into an if() statement
in net-next, whilst a newline was added to that CHECK
call in 'net'.  Thanks to Daniel for the merge resolution.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support setting the link speed of CN23XX-225 cards (which can do 25Gbps or
10Gbps) via ethtool_ops.set_link_ksettings.

Also fix the function assigned to ethtool_ops.get_link_ksettings to use the
new link_ksettings api completely (instead of partially via
ethtool_convert_legacy_u32_to_link_mode).
Signed-off-by: NWeilin Chang <weilin.chang@cavium.com>
Acked-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sebastian Andrzej Siewior says:

====================
3c59x patches and the removal of an unused function

The first patch removes an unused function. The goal of remaining three
patches is to get rid of the local_irq_save() usage in the driver which
benefits -RT.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vortex_boomerang_interrupt() is invoked from vortex_tx_timeout() or
poll_vortex() interrupts must be disabled. This detaches the interrupt
disable logic from locking which requires patching for PREEMPT_RT.

The advantage of avoiding spin_lock_irqsave() in the interrupt handler is
minimal, but converting it removes all the extra code for callers which
come not from interrupt context.

Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAnna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Locking is done in the same way in _vortex_interrupt() and
_boomerang_interrupt(). To prevent duplication, move the locking into the
calling vortex_boomerang_interrupt() function.

No functional change.

Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAnna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If vp->full_bus_master_tx is set, vp->full_bus_master_rx is set as well
(see vortex_probe1()). Therefore the conditionals for the decision if
boomerang or vortex ISR is executed have the same result. Instead of
repeating the explicit conditional execution of the boomerang/vortex ISR,
move it into an own function.

No functional change.

Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAnna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 67db3e4b ("tcp: no longer hold ehash lock while calling
tcp_get_info()") removes the only users of u64_stats_update_end/begin_raw()
without removing the function in header file.

Remove no longer used functions.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NAnna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generated files udpgso* shouldn't be part of TEST_PROGS, they are
used by udpgso.sh and udpgsp_bench.sh. They should be added to the
TEST_GEN_FILES to get installed without being added to the main
run_kselftest.sh script.

Fixes: 3a687bef ("selftests: udp gso benchmark")
Signed-off-by: NAnders Roxell <anders.roxell@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS updates for your net-next
tree, more relevant updates in this batch are:

1) Add Maglev support to IPVS. Moreover, store lastest server weight in
   IPVS since this is needed by maglev, patches from from Inju Song.

2) Preparation works to add iptables flowtable support, patches
   from Felix Fietkau.

3) Hand over flows back to conntrack slow path in case of TCP RST/FIN
   packet is seen via new teardown state, also from Felix.

4) Add support for extended netlink error reporting for nf_tables.

5) Support for larger timeouts that 23 days in nf_tables, patch from
   Florian Westphal.

6) Always set an upper limit to dynamic sets, also from Florian.

7) Allow number generator to make map lookups, from Laura Garcia.

8) Use hash_32() instead of opencode hashing in IPVS, from Vicent Bernat.

9) Extend ip6tables SRH match to support previous, next and last SID,
   from Ahmed Abdelsalam.

10) Move Passive OS fingerprint nf_osf.c, from Fernando Fernandez.

11) Expose nf_conntrack_max through ctnetlink, from Florent Fourcot.

12) Several housekeeping patches for xt_NFLOG, x_tables and ebtables,
   from Taehee Yoo.

13) Unify meta bridge with core nft_meta, then make nft_meta built-in.
   Make rt and exthdr built-in too, again from Florian.

14) Missing initialization of tbl->entries in IPVS, from Cong Wang.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This must now use a 64bit jiffies value, else we set
a bogus timeout on 32bit.

Fixes: 8e1102d5 ("netfilter: nf_tables: support timeouts larger than 23 days")
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

IPCTNL_MSG_CT_GET_STATS netlink command allow to monitor current number
of conntrack entries. However, if one wants to compare it with the
maximum (and detect exhaustion), the only solution is currently to read
sysctl value.

This patch add nf_conntrack_max value in netlink message, and simplify
monitoring for application built on netlink API.
Signed-off-by: NFlorent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Add nf_osf_ttl() and nf_osf_match() into nf_osf.c to prepare for
nf_tables support.
Signed-off-by: NFernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

These macros allow conveniently declaring arrays which use NFT_{RT,CT}_*
values as indexes.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

IPv6 Segment Routing Header (SRH) contains a list of SIDs to be crossed
by SR encapsulated packet. Each SID is encoded as an IPv6 prefix.

When a Firewall receives an SR encapsulated packet, it should be able
to identify which node previously processed the packet (previous SID),
which node is going to process the packet next (next SID), and which
node is the last to process the packet (last SID) which represent the
final destination of the packet in case of inline SR mode.

An example use-case of using these features could be SID list that
includes two firewalls. When the second firewall receives a packet,
it can check whether the packet has been processed by the first firewall
or not. Based on that check, it decides to apply all rules, apply just
subset of the rules, or totally skip all rules and forward the packet to
the next SID.

This patch extends SRH match to support matching previous SID, next SID,
and last SID.
Signed-off-by: NAhmed Abdelsalam <amsalam20@gmail.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

The modulus in the hash function was limited to > 1 as initially
there was no sense to create a hashing of just one element.

Nevertheless, there are certain cases specially for load balancing
where this case needs to be addressed.

This patch fixes the following error.

Error: Could not process rule: Numerical result out of range
add rule ip nftlb lb01 dnat to jhash ip saddr mod 1 map { 0: 192.168.0.10 }
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

The solution comes to force the hash to 0 when the modulus is 1.
Signed-off-by: NLaura Garcia Liebana <nevola@gmail.com>

This patch includes a new attribute in the numgen structure to allow
the lookup of an element based on the number generator as a key.

For this purpose, different ops have been included to extend the
current numgen inc functions.

Currently, only supported for numgen incremental operations, but
it will be supported for random in a follow-up patch.
Signed-off-by: NLaura Garcia Liebana <nevola@gmail.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

This slipped through the cracks in the followup set to the fib6_info flip.
Rename rt6_next to fib6_next.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If bpf_map_precharge_memlock() did not fail, then we set err to zero.
However, any subsequent failure from either alloc_percpu() or the
bpf_map_area_alloc() will return ERR_PTR(0) which in find_and_alloc_map()
will cause NULL pointer deref.

In devmap we have the convention that we return -EINVAL on page count
overflow, so keep the same logic here and just set err to -ENOMEM
after successful bpf_map_precharge_memlock().

Fixes: fbfc504a ("bpf: introduce new bpf AF_XDP map type BPF_MAP_TYPE_XSKMAP")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Björn Töpel <bjorn.topel@intel.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Jakub Kicinski says:

====================
This series centres on NFP offload of bpf_event_output().  The
first patch allows perf event arrays to be used by offloaded
programs.  Next patch makes the nfp driver keep track of such
arrays to be able to filter FW events referring to maps.
Perf event arrays are not device bound.  Having driver
reimplement and manage the perf array seems brittle and unnecessary.

Patch 4 moves slightly the verifier step which replaces map fds
with map pointers.  This is useful for nfp JIT since we can then
easily replace host pointers with NFP table ids (patch 6).  This
allows us to lift the limitation on map helpers having to be used
with the same map pointer on all paths.  Second use of replacing
fds with real host map pointers is that we can use the host map
pointer as a key for FW events in perf event array offload.

Patch 5 adds perf event output offload support for the NFP.

There are some differences between bpf_event_output() offloaded
and non-offloaded version.  The FW messages which carry events
may get dropped and reordered relatively easily.  The return codes
from the helper are also not guaranteed to match the host.  Users
are warned about some of those discrepancies with a one time
warning message to kernel logs.

bpftool gains an ability to dump perf ring events in a very simple
format.  This was very useful for testing and simple debug, maybe
it will be useful to others?

Last patch is a trivial comment fix.
====================
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Comments in the verifier refer to free_bpf_prog_info() which
seems to have never existed in tree.  Replace it with
free_used_maps().
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Users of BPF sooner or later discover perf_event_output() helpers
and BPF_MAP_TYPE_PERF_EVENT_ARRAY.  Dumping this array type is
not possible, however, we can add simple reading of perf events.
Create a new event_pipe subcommand for maps, this sub command
will only work with BPF_MAP_TYPE_PERF_EVENT_ARRAY maps.

Parts of the code from samples/bpf/trace_output_user.c.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Move the get_possible_cpus() function to shared code.  No functional
changes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Instead of spelling [hex] BYTES everywhere use DATA as keyword
for generalized value.  This will help us keep the messages
concise when longer command are added in the future.  It will
also be useful once BTF support comes.  We will only have to
change the definition of DATA.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Kernel will now replace map fds with actual pointer before
calling the offload prepare.  We can identify those pointers
and replace them with NFP table IDs instead of loading the
table ID in code generated for CALL instruction.

This allows us to support having the same CALL being used with
different maps.

Since we don't want to change the FW ABI we still need to
move the TID from R1 to portion of R0 before the jump.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>