Jose Abreu says:

====================
Documentation: stmmac documentation improvements

Converts stmmac documentation to RST format.

1) Adds missing entry of stmmac documentation to MAINTAINERS.

2) Converts stmmac documentation to RST format and adds some new info.

3) Adds the new RST file to the list of files.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the stmmac RST file to the index.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the documentation of the driver to RST format and delete the old
txt and old information that no longer applies.

Also, add some new information.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the missing entry for the file that documents the stmicro Ethernet
driver stmmac.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use __func__ to print the function name instead of hard coded string.
BTW, replace printk(KERN_DEBUG, ...) with netdev_dbg.
Signed-off-by: NChen Zhou <chenzhou10@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Chen Zhou says:

====================
net: ch9200: code cleanup

patch 1 introduce __func__ in debug message.
patch 2 remove unnecessary return.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The return is not needed, remove it.
Signed-off-by: NChen Zhou <chenzhou10@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use __func__ to print the function name instead of hard coded string.
Signed-off-by: NChen Zhou <chenzhou10@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: driver updates

These are a few little updates for the ionic network driver.

v2: dropped IBM msi patch
    added fix for a compiler warning
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Build checks have pointed out that 'hb' can theoretically
be used before set, so let's initialize it and get rid
of the compiler complaint.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure the NIC drops packets that are larger than the
specified MTU.

The front end of the NIC will accept packets larger than MTU and
will copy all the data it can to fill up the driver's posted
buffers - if the buffers are not long enough the packet will
then get dropped.  With the Rx SG buffers allocagted as full
pages, we are currently setting up more space than MTU size
available and end up receiving some packets that are larger
than MTU, up to the size of buffers posted.  To be sure the
NIC doesn't waste our time with oversized packets we need to
lie a little in the SG descriptor about how long is the last
SG element.

At dealloc time, we know the allocation was a page, so the
deallocation doesn't care about what length we put in the
descriptor.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a counter for packets dropped by the driver, typically
for bad size or a receive error seen by the device.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The subdevice concept is not being used in the driver, so
drop the references to it.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-01-06

This series contains updates to igc to add basic support for
timestamping.

Vinicius adds basic support for timestamping and enables ptp4l/phc2sys
to work with i225 devices.  Initially, adds the ability to read and
adjust the PHC clock.  Patches 2 & 3 enable and retrieve hardware
timestamps.  Patch 4 implements the ethtool ioctl that ptp4l uses to
check what timestamping methods are supported.  Lastly, added support to
do timestamping using the "Start of Packet" signal from the PHY, which
is now supported in i225 devices.

While i225 does support multiple PTP domains, with multiple timestamping
registers, we currently only support one PTP domain and use only one of
the timestamping registers for implementation purposes.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Unique mv88e6xxx IRQ names

There are a few boards which have multiple mv88e6xxx switches. With
such boards, it can be hard to determine which interrupts belong to
which switches. Make the interrupt names unique by including the
device name in the interrupt name. For the SERDES interrupt, also
include the port number. As a result of these patches ZII devel C
looks like:

 50:          0  gpio-vf610  27 Level     mv88e6xxx-0.1:00
 54:          0  mv88e6xxx-g1   3 Edge      mv88e6xxx-0.1:00-g1-atu-prob
 56:          0  mv88e6xxx-g1   5 Edge      mv88e6xxx-0.1:00-g1-vtu-prob
 58:          0  mv88e6xxx-g1   7 Edge      mv88e6xxx-0.1:00-g2
 61:          0  mv88e6xxx-g2   1 Edge      !mdio-mux!mdio@1!switch@0!mdio:01
 62:          0  mv88e6xxx-g2   2 Edge      !mdio-mux!mdio@1!switch@0!mdio:02
 63:          0  mv88e6xxx-g2   3 Edge      !mdio-mux!mdio@1!switch@0!mdio:03
 64:          0  mv88e6xxx-g2   4 Edge      !mdio-mux!mdio@1!switch@0!mdio:04
 70:          0  mv88e6xxx-g2  10 Edge      mv88e6xxx-0.1:00-serdes-10
 75:          0  mv88e6xxx-g2  15 Edge      mv88e6xxx-0.1:00-watchdog
 76:          5  gpio-vf610  26 Level     mv88e6xxx-0.2:00
 80:          0  mv88e6xxx-g1   3 Edge      mv88e6xxx-0.2:00-g1-atu-prob
 82:          0  mv88e6xxx-g1   5 Edge      mv88e6xxx-0.2:00-g1-vtu-prob
 84:          4  mv88e6xxx-g1   7 Edge      mv88e6xxx-0.2:00-g2
 87:          2  mv88e6xxx-g2   1 Edge      !mdio-mux!mdio@2!switch@0!mdio:01
 88:          0  mv88e6xxx-g2   2 Edge      !mdio-mux!mdio@2!switch@0!mdio:02
 89:          0  mv88e6xxx-g2   3 Edge      !mdio-mux!mdio@2!switch@0!mdio:03
 90:          0  mv88e6xxx-g2   4 Edge      !mdio-mux!mdio@2!switch@0!mdio:04
 95:          3  mv88e6xxx-g2   9 Edge      mv88e6xxx-0.2:00-serdes-9
 96:          0  mv88e6xxx-g2  10 Edge      mv88e6xxx-0.2:00-serdes-10
101:          0  mv88e6xxx-g2  15 Edge      mv88e6xxx-0.2:00-watchdog

Interrupt names like !mdio-mux!mdio@2!switch@0!mdio:01 are created by
phylib for the integrated PHYs. The mv88e6xxx driver does not
determine these names.
====================
Tested-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dynamically generate a unique interrupt name for the VTU and ATU,
based on the device name.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dynamically generate a unique g2 interrupt name, based on the
device name.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dynamically generate a unique watchdog interrupt name, based on the
device name.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dynamically generate a unique SERDES interrupt name, based on the
device name and the port the SERDES is for. For example:

 95:          3  mv88e6xxx-g2   9 Edge      mv88e6xxx-0.2:00-serdes-9
 96:          0  mv88e6xxx-g2  10 Edge      mv88e6xxx-0.2:00-serdes-10

The 0.2:00 indicates the switch and -9 indicates port 9.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dynamically generate a unique switch interrupt name, based on the
device name.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For better accuracy, i225 is able to do timestamping using the Start of
Packet signal from the PHY.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This command allows igc to report what types of timestamping are
supported. ptp4l uses this to detect if the hardware supports
timestamping.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds support for timestamping packets being transmitted.

Based on the code from i210. The basic differences is that i225 has 4
registers to store the transmit timestamps (i210 has one). Right now,
we only support retrieving from one register, support for using the
other registers will be added later.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds support for timestamping received packets.

It is based on the i210, as many features of i225 work the same way.
The main difference from i210 is that i225 has support for choosing
the timer register to use when timestamping packets. Right now, we
only support using timer 0. The other difference is that i225 stores
two timestamps in the receive descriptor, right now, we only retrieve
one.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Michal Kubecek says:

====================
ethtool: allow nesting of begin() and complete() callbacks

The ethtool ioctl interface used to guarantee that ethtool_ops callbacks
were always called in a block between calls to ->begin() and ->complete()
(if these are defined) and that this whole block was executed with RTNL
lock held:

	rtnl_lock();
	ops->begin();
	/* other ethtool_ops calls */
	ops->complete();
	rtnl_unlock();

This prevented any nesting or crossing of the begin-complete blocks.
However, this is no longer guaranteed even for ioctl interface as at least
ethtool_phys_id() releases RTNL lock while waiting for a timer. With the
introduction of netlink ethtool interface, the begin-complete pairs are
naturally nested e.g. when a request triggers a netlink notification.

Fortunately, only minority of networking drivers implements begin() and
complete() callbacks and most of those that do, fall into three groups:

  - wrappers for pm_runtime_get_sync() and pm_runtime_put()
  - wrappers for clk_prepare_enable() and clk_disable_unprepare()
  - begin() checks netif_running() (fails if false), no complete()

First two have their own refcounting, third is safe w.r.t. nesting of the
blocks.

Only three in-tree networking drivers need an update to deal with nesting
of begin() and complete() calls: via-velocity and epic100 perform resume
and suspend on their own and wil6210 completely serializes the calls using
its own mutex (which would lead to a deadlock if a request request
triggered a netlink notification). The series addresses these problems.

changes between v1 and v2:
  - fix inverted condition in epic100 ethtool_begin() (thanks to Andrew
    Lunn)
====================
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike most networking drivers using begin() and complete() ethtool_ops
callbacks to resume a device which is down and suspend it again when done,
epic100 does not use standard refcounted infrastructure but sets device
sleep state directly.

With the introduction of netlink ethtool interface, we may have nested
begin-complete blocks so that inner complete() would put the device back to
sleep for the rest of the outer block.

To avoid rewriting an old and not very actively developed driver, just add
a nesting counter and only perform resume and suspend on the outermost
level.
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike most networking drivers using begin() and complete() ethtool_ops
callbacks to resume a device which is down and suspend it again when done,
via-velocity does not use standard refcounted infrastructure but sets
device sleep state directly.

With the introduction of netlink ethtool interface, we may have nested
begin-complete blocks so that inner complete() would put the device back to
sleep for the rest of the outer block.

To avoid rewriting an old and not very actively developed driver, just add
a nesting counter and only perform resume and suspend on the outermost
level.
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The wil6210 driver locks a mutex in begin() ethtool_ops callback and
unlocks it in complete() so that all ethtool requests are serialized. This
is not going to work correctly with netlink interface; e.g. when ioctl
triggers a netlink notification, netlink code would call begin() again
while the mutex taken by ioctl code is still held by the same task.

Let's get rid of the begin() and complete() callbacks and move the mutex
locking into the remaining ethtool_ops handlers except get_drvinfo which
only copies strings that are not changing so that there is no need for
serialization.
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent MD5 tests added duplicate configuration in the default VRF.
This change exposed a bug in existing tests designed to verify no
connection when client and server are not in the same domain. The
server should be running bound to the vrf device with the client run
in the default VRF (the -2 option is meant for validating connection
data). Fix the option for both tests.

While technically this is a bug in previous releases, the tests are
properly failing since the default VRF does not have any routing
configuration so there really is no need to backport to prior releases.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'gtp_encap_disable_sock(sk)' handles the case where sk is NULL, so there
is no need to test it before calling the function.

This saves a few line of code.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Disable checks in hardware pipeline

Amit says:

The hardware pipeline contains some checks that, by default, are
configured to drop packets. Since the software data path does not drop
packets due to these reasons and since we are interested in offloading
the software data path to hardware, then these checks should be disabled
in the hardware pipeline as well.

This patch set changes mlxsw to disable four of these checks and adds
corresponding selftests. The tests pass both when the software data path
is exercised (using veth pair) and when the hardware data path is
exercised (using mlxsw ports in loopback).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test case to check that packets are not dropped when they need to be
routed and their destination is link-local, i.e., 169.254.0.0/16.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check drops packets if they need to be routed and their destination
IP is link-local, i.e., belongs to 169.254.0.0/16 address range.

Disable the check since the kernel forwards such packets and does not
drop them.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test case to check that packets are not dropped when they need to be
routed and their source IP equals to their destination IP.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check drops packets if they need to be routed and their source IP
equals to their destination IP.

Disable the check since the kernel forwards such packets and does not
drop them.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test case to check that packets are not dropped when they need to be
routed and their multicast MAC mismatched to their multicast destination
IP.

i.e., destination IP is multicast and
	* for IPV4: DMAC !=  {01-00-5E-0 (25 bits), DIP[22:0]}
	* for IPV6: DMAC !=  {33-33-0 (16 bits), DIP[31:0]}
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check drops packets if they need to be routed and their multicast
MAC mismatched to their multicast destination IP.

For IPV4:
DMAC is mismatched if it is different from {01-00-5E-0 (25 bits),
DIP[22:0]}

For IPV6:
DMAC is mismatched if it is different from {33-33-0 (16 bits),
DIP[31:0]}

Disable the check since the kernel forwards such packets and does not
drop them.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test case to check that packets are not dropped when they need to be
routed and their source IP in class E, (i.e., 240.0.0.0 –
255.255.255.254).
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check drops packets if they need to be routed and their source IP is
from class E, i.e., belongs to 240.0.0.0/4 address range, but different
from 255.255.255.255.

Disable the check since the kernel forwards such packets and does not
drop them.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows the creation of the /dev/ptpX device for i225, and reading
and writing the time.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>