Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 04 7月, 2012 3 次提交
    • R
      PM / Domains: Add preliminary support for cpuidle, v2 · cbc9ef02
      由 Rafael J. Wysocki 提交于 
      On some systems there are CPU cores located in the same power
domains as I/O devices.  Then, power can only be removed from the
domain if all I/O devices in it are not in use and the CPU core
is idle.  Add preliminary support for that to the generic PM domains
framework.

First, the platform is expected to provide a cpuidle driver with one
extra state designated for use with the generic PM domains code.
This state should be initially disabled and its exit_latency value
should be set to whatever time is needed to bring up the CPU core
itself after restoring power to it, not including the domain's
power on latency.  Its .enter() callback should point to a procedure
that will remove power from the domain containing the CPU core at
the end of the CPU power transition.

The remaining characteristics of the extra cpuidle state, referred to
as the "domain" cpuidle state below, (e.g. power usage, target
residency) should be populated in accordance with the properties of
the hardware.

Next, the platform should execute genpd_attach_cpuidle() on the PM
domain containing the CPU core.  That will cause the generic PM
domains framework to treat that domain in a special way such that:

 * When all devices in the domain have been suspended and it is about
   to be turned off, the states of the devices will be saved, but
   power will not be removed from the domain.  Instead, the "domain"
   cpuidle state will be enabled so that power can be removed from
   the domain when the CPU core is idle and the state has been chosen
   as the target by the cpuidle governor.

 * When the first I/O device in the domain is resumed and
   __pm_genpd_poweron(() is called for the first time after
   power has been removed from the domain, the "domain" cpuidle
   state will be disabled to avoid subsequent surprise power removals
   via cpuidle.

The effective exit_latency value of the "domain" cpuidle state
depends on the time needed to bring up the CPU core itself after
restoring power to it as well as on the power on latency of the
domain containing the CPU core.  Thus the "domain" cpuidle state's
exit_latency has to be recomputed every time the domain's power on
latency is updated, which may happen every time power is restored
to the domain, if the measured power on latency is greater than
the latency stored in the corresponding generic_pm_domain structure.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: NKevin Hilman <khilman@ti.com>
      cbc9ef02
    • R
      PM / cpuidle: Add driver reference counter · 6e797a07
      由 Rafael J. Wysocki 提交于 
      Add a reference counter for the cpuidle driver, so that it can't
be unregistered when it is in use.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      6e797a07
    • S
      cpuidle: move field disable from per-driver to per-cpu · dc7fd275
      由 ShuoX Liu 提交于 
      Andrew J.Schorr raises a question.  When he changes the disable setting on
a single CPU, it affects all the other CPUs.  Basically, currently, the
disable field is per-driver instead of per-cpu.  All the C states of the
same driver are shared by all CPU in the same machine.

The patch changes the `disable' field to per-cpu, so we could set this
separately for each cpu.
Signed-off-by: NShuoX Liu <shuox.liu@intel.com>
Reported-by: NAndrew J.Schorr <aschorr@telemetry-investments.com>
Reviewed-by: NYanmin Zhang <yanmin_zhang@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      dc7fd275
  3. 01 7月, 2012 1 次提交
  5. 21 6月, 2012 3 次提交
  7. 19 6月, 2012 1 次提交
  9. 18 6月, 2012 2 次提交
    • S
      ftrace: Make all inline tags also include notrace · 93b3cca1
      由 Steven Rostedt 提交于 
      Commit 5963e317 ("ftrace/x86: Do not change stacks in DEBUG when
calling lockdep") prevented lockdep calls from the int3 breakpoint handler
from reseting the stack if a function that was called was in the process
of being converted for tracing and had a breakpoint on it. The idea is,
before calling the lockdep code, do a load_idt() to the special IDT that
kept the breakpoint stack from reseting. This worked well as a quick fix
for this kernel release, until a certain config caused a lockup in the
function tracer start up tests.

Investigating it, I found that the load_idt that was used to prevent
the int3 from changing stacks was itself being traced!

Even though the config had CONFIG_OPTIMIZE_INLINING disabled, and
all 'inline' tags were set to always inline, there were still cases that
it did not inline! This was caused by CONFIG_PARAVIRT_GUEST, where it
would add a pointer to the native_load_idt() which made that function
to be traced.

Commit 45959ee7 ("ftrace: Do not function trace inlined functions")
only touched the 'inline' tags when CONFIG_OPMITIZE_INLINING was enabled.
PARAVIRT_GUEST shows that this was not enough and we need to also
mark always_inline with notrace as well.
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Tested-by: NFengguang Wu <wfg@linux.intel.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
      93b3cca1
    • T
      NFSv4.1: Fix umount when filelayout DS is also the MDS · 2a4c8994
      由 Trond Myklebust 提交于 
      Currently there is a 'chicken and egg' issue when the DS is also the mounted
MDS. The nfs_match_client() reference from nfs4_set_ds_client bumps the
cl_count, the nfs_client is not freed at umount, and nfs4_deviceid_purge_client
is not called to dereference the MDS usage of a deviceid which holds a
reference to the DS nfs_client.  The result is the umount program returns,
but the nfs_client is not freed, and the cl_session hearbeat continues.

The MDS (and all other nfs mounts) lose their last nfs_client reference in
nfs_free_server when the last nfs_server (fsid) is umounted.
The file layout DS lose their last nfs_client reference in destroy_ds
when the last deviceid referencing the data server is put and destroy_ds is
called. This is triggered by a call to nfs4_deviceid_purge_client which
removes references to a pNFS deviceid used by an MDS mount.

The fix is to track how many pnfs enabled filesystems are mounted from
this server, and then to purge the device id cache once that count reaches
zero.
Reported-by: NJorge Mora <Jorge.Mora@netapp.com>
Reported-by: NAndy Adamson <andros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
      2a4c8994
  11. 16 6月, 2012 4 次提交
    • R
      vga_switcheroo.h: fix pci_dev warning · f8fee8f5
      由 Randy Dunlap 提交于 
      Fix warnings on some architectures/configs (not on x86):

include/linux/vga_switcheroo.h:28:30: warning: 'struct pci_dev' declared inside parameter list [enabled by default]
include/linux/vga_switcheroo.h:28:30: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc:	Takashi Iwai <tiwai@suse.de>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>
      f8fee8f5
    • H
      swap: fix shmem swapping when more than 8 areas · 9b15b817
      由 Hugh Dickins 提交于 
      Minchan Kim reports that when a system has many swap areas, and tmpfs
swaps out to the ninth or more, shmem_getpage_gfp()'s attempts to read
back the page cannot locate it, and the read fails with -ENOMEM.

Whoops.  Yes, I blindly followed read_swap_header()'s pte_to_swp_entry(
swp_entry_to_pte()) technique for determining maximum usable swap
offset, without stopping to realize that that actually depends upon the
pte swap encoding shifting swap offset to the higher bits and truncating
it there.  Whereas our radix_tree swap encoding leaves offset in the
lower bits: it's swap "type" (that is, index of swap area) that was
truncated.

Fix it by reducing the SWP_TYPE_SHIFT() in swapops.h, and removing the
broken radix_to_swp_entry(swp_to_radix_entry()) from read_swap_header().

This does not reduce the usable size of a swap area any further, it
leaves it as claimed when making the original commit: no change from 3.0
on x86_64, nor on i386 without PAE; but 3.0's 512GB is reduced to 128GB
per swapfile on i386 with PAE.  It's not a change I would have risked
five years ago, but with x86_64 supported for ten years, I believe it's
appropriate now.

Hmm, and what if some architecture implements its swap pte with offset
encoded below type? That would equally break the maximum usable swap
offset check.  Happily, they all follow the same tradition of encoding
offset above type, but I'll prepare a check on that for next.
Reported-and-Reviewed-and-Tested-by: NMinchan Kim <minchan@kernel.org>
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org [3.1, 3.2, 3.3, 3.4]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      9b15b817
    • E
      net: remove skb_orphan_try() · 62b1a8ab
      由 Eric Dumazet 提交于 
      Orphaning skb in dev_hard_start_xmit() makes bonding behavior
unfriendly for applications sending big UDP bursts : Once packets
pass the bonding device and come to real device, they might hit a full
qdisc and be dropped. Without orphaning, the sender is automatically
throttled because sk->sk_wmemalloc reaches sk->sk_sndbuf (assuming
sk_sndbuf is not too big)

We could try to defer the orphaning adding another test in
dev_hard_start_xmit(), but all this seems of little gain,
now that BQL tends to make packets more likely to be parked
in Qdisc queues instead of NIC TX ring, in cases where performance
matters.

Reverts commits :
fc6055a5 net: Introduce skb_orphan_try()
87fd308c net: skb_tx_hash() fix relative to skb_orphan_try()
and removes SKBTX_DRV_NEEDS_SK_REF flag
Reported-and-bisected-by: NJean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      62b1a8ab
    • K
      kmsg - kmsg_dump() use iterator to receive log buffer content · e2ae715d
      由 Kay Sievers 提交于 
      Provide an iterator to receive the log buffer content, and convert all
kmsg_dump() users to it.

The structured data in the kmsg buffer now contains binary data, which
should no longer be copied verbatim to the kmsg_dump() users.

The iterator should provide reliable access to the buffer data, and also
supports proper log line-aware chunking of data while iterating.
Signed-off-by: NKay Sievers <kay@vrfy.org>
Tested-by: NTony Luck <tony.luck@intel.com>
Reported-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Tested-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      e2ae715d
  13. 14 6月, 2012 3 次提交
  15. 12 6月, 2012 1 次提交
  17. 11 6月, 2012 2 次提交
  19. 10 6月, 2012 1 次提交
    • P
      net: Make linux/tcp.h C++ friendly (trivial) · 8876d6b5
      由 Paul Pluzhnikov 提交于 
      I originally sent this patch to <trivial@kernel.org>, but Jiri Kosina did
not feel that this is fully appropriate for the trivial tree.

Using linux/tcp.h from C++ results in:

cat t.cc
#include <linux/tcp.h>
int main() { }

g++ -c t.cc

In file included from t.cc:1:
/usr/include/linux/tcp.h:72: error: '__u32 __fswab32(__u32)' cannot appear in a constant-expression
/usr/include/linux/tcp.h:72: error: a function call cannot appear in a constant-expression
...

Attached trivial patch fixes this problem.

Tested:
- the t.cc above compiles with g++ and
- the following program generates the same output before/after
  the patch:

#include <linux/tcp.h>
#include <stdio.h>

int main ()
{
#define P(a) printf("%s: %08x\n", #a, (int)a)
 P(TCP_FLAG_CWR);
 P(TCP_FLAG_ECE);
 P(TCP_FLAG_URG);
 P(TCP_FLAG_ACK);
 P(TCP_FLAG_PSH);
 P(TCP_FLAG_RST);
 P(TCP_FLAG_SYN);
 P(TCP_FLAG_FIN);
 P(TCP_RESERVED_BITS);
 P(TCP_DATA_OFFSET);
#undef P
 return 0;
}
Signed-off-by: NPaul Pluzhnikov <ppluzhnikov@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8876d6b5
  21. 08 6月, 2012 5 次提交
  23. 07 6月, 2012 2 次提交
  25. 06 6月, 2012 5 次提交
  27. 05 6月, 2012 1 次提交
    • T
      NFSv4: Fix an Oops in the open recovery code · 1549210f
      由 Trond Myklebust 提交于 
      The open recovery code does not need to request a new value for the
mdsthreshold, and so does not allocate a struct nfs4_threshold.
The problem is that encode_getfattr_open() will still request an
mdsthreshold, and so we end up Oopsing in decode_attr_mdsthreshold.

This patch fixes encode_getfattr_open so that it doesn't request an
mdsthreshold when the caller isn't asking for one. It also fixes
decode_attr_mdsthreshold so that it errors if the server returns
an mdsthreshold that we didn't ask for (instead of Oopsing).
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Cc: Andy Adamson <andros@netapp.com>
      1549210f
  29. 04 6月, 2012 3 次提交
  31. 03 6月, 2012 1 次提交
    • L
      tty: Revert the tty locking series, it needs more work · f309532b
      由 Linus Torvalds 提交于 
      This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.

The main revert is d29f3ef3 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:

  fde86d31 - tty: add lockdep annotations
  8f6576ad - tty: fix ldisc lock inversion trace
  d3ca8b64 - pty: Fix lock inversion
  b1d679af - tty: drop the pty lock during hangup
  abcefe5f - tty/amiserial: Add missing argument for tty_unlock()
  fd11b42e - cris: fix missing tty arg in wait_event_interruptible_tty call
  d29f3ef3 - tty_lock: Localise the lock

The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      f309532b
  33. 02 6月, 2012 2 次提交
    • A
      new helper: signal_delivered() · efee984c
      由 Al Viro 提交于 
      Does block_sigmask() + tracehook_signal_handler();  called when
sigframe has been successfully built.  All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).

I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
      efee984c
    • A
      most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set · 77097ae5
      由 Al Viro 提交于 
      Only 3 out of 63 do not.  Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
      77097ae5