- 30 1月, 2006 1 次提交
-
-
由 Sumant Patro 提交于
This patch (originally submitted by Christoph Hellwig) removes code duplication in megasas_build_cmd. It also defines MEGASAS_IOC_FIRMWARE32 to allow 64 bit compiled applications to work. Signed-off-by: NSumant Patro <Sumant.Patro@lsil.com> Rejections fixed and Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 27 1月, 2006 1 次提交
-
-
由 brking@us.ibm.com 提交于
When the scsi_execute_async interface was added it ended up reducing the flexibility of userspace to send arbitrary scsi commands through sg using SG_IO. The SG_IO interface allows userspace to specify the CDB length. This is now ignored in scsi_execute_async and it is guessed using the COMMAND_SIZE macro, which is not always correct, particularly for vendor specific commands. This patch adds a cmd_len parameter to the scsi_execute_async interface to allow the caller to specify the length of the CDB. Signed-off-by: NBrian King <brking@us.ibm.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 26 1月, 2006 7 次提交
-
-
由 Jack Hammer 提交于
Resetting the adapter causes the ServeRAID driver to exceed the max time allowed by the softlock watchdog. Resetting the hardware can easily require 30 or more seconds. To avoid the "BUG: soft lockup detected on CPU#0!" result, this patch replaces the mdelay() calls in the initialization/reset routines with msleep(). Signed-off-by: NJack Hammer <jack_hammer@adaptec.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Internal lun discovery has been removed since fc_transport integration. Short-circuiting for tape-devices in qla2x00_update_fcport() could inadvertently result in a blocked rport timing-out and its targets being reaped. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
A target can LOGO an initiator at any time (i.e. during I/O, due to a controller hicup, or as a simple authentication mechanism after an initial CDB command), when this occurs, the driver attempts to relogin (PLOGI) to the device via the DPC thread. Add code to make the appropriate upcall to the FC transport layer (fc_remote_port_add()) upon successful completion of the PLOGI. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
The driver can typically detect port-loss during an interrupt context (i.e. via interrogation of a status IOCB's completion status [CS_PORT_LOGGED_OUT]. Due to the calling requirements of the fc_rport APIs, the driver would defer removal of the device to the default workqueue. If the work-item was preceded by an event which caused the port to obtain visibility (relogin successful, target re-logged into the topology), deferred removal could inadvertently drop the rport. The code also no longer defers removal via the default workqueue, instead opting for use of the driver's own DPC thread. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Guennadi Liakhovetski 提交于
The patch below "fixes" calculation of the virt_addr for the AUTO_REQSENSE case. I put "fixes" in quotes because the real fix would be to completely remove it, but that's beyond the scope of this patch. Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Dave C Boutcher 提交于
New versions of the Power5 firmware can send a "re-enable" message to the virtual scsi adapter. This fix makes us handle the message correctly. Without it, the driver goes catatonic and the system crashes unpleasantly. Signed-off-by: NDave Boutcher <sleddog@us.ibm.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Jes Sorensen 提交于
Remove support for kernels older than 2.6.0. Signed-off-by: NJes Sorensen <jes@sgi.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
- 18 1月, 2006 4 次提交
-
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Somewhat cleaner in the resync as someone cleaned up the pio xfer users Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jason Gaston 提交于
Signed-off-by: NJason Gaston <Jason.d.gaston@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 17 1月, 2006 5 次提交
-
-
由 Alan Cox 提交于
This ought to be simple but for PIO2 we have to poke around the drive data to get it 100% correct. Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Alan Cox 提交于
I misread the spec when doing the original. I've tested the corrected version with pre UDMA drives and it now picks the right modes. This is a specific bug fix rather than an update or new feature item. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Yusuf Iskenderoglu 提交于
-
由 Oliver Weihe 提交于
-
由 Jason Gaston 提交于
This patch adds the Intel ICH8 DID's to the ahci.c file for AHCI mode SATA support. Signed-off-by: NJason Gaston <Jason.d.gaston@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 15 1月, 2006 22 次提交
-
-
由 Arjan van de Ven 提交于
Remove the "inline" keyword from a bunch of big functions in the kernel with the goal of shrinking it by 30kb to 40kb Signed-off-by: NArjan van de Ven <arjan@infradead.org> Signed-off-by: NIngo Molnar <mingo@elte.hu> Acked-by: NJeff Garzik <jgarzik@pobox.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Alexey Dobriyan 提交于
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
由 Adrian Bunk 提交于
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Given the semantic changes in both the device-model and fc-transport APIs, the driver's handling of port-type RSCNs via a series of ADISCs and PLOGIs can cause series of badness ranging from unexpectedly device loss to devices not being discovered. In the interim, disable (via a module-parameter) this feature and allow RSCN management to continue to occur within the driver's DPC thread. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Similarly to other ISPs, set execution throttle to maximum allowed value since 'throttling' is done on a per-lun basis via queue-depth. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Simplify essentially duplicate load RISC RAM implementation in qla2x00_load_ram_ext() and qla2x00_load_ram(). Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Swing/emphasis settings in NVRAM were not being honoured due to the driver not converting the serial-link options from LE to host-endian format. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
If the Get Port Database call fails during local-loop update, then schedule the DPC routine to perform a rescan as the firmware would have updated the Get ID List port-entries of their new state. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Small changes to register retrieval and order as per latest firmware specification. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Driver would not correctly re-enable the write-protection bits of the flash part after updates. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Problem report (against 2.4.x driver) from Jeff Layton <jlayton@redhat.com>: An OEM noticed that the U6 qla2200 driver would hang for around 2 minutes at boot time and then proceed normally. I found that the delay was occurring when loading the new firmware into the card, and was due to a schedule_timeout(10) added to the bottom of the polling loop. Some testing showed that the load ram operation on the card was very quick (on the order of a couple of jiffies), but the sleep in the polling loop was making each operation take around 25-30. The attached patch corrects this by making it skip sleeping during the load ram operation, since I believe we only do that when the module is plugged in. It also skips sleeping if the mbox_int flag got set during the current loop. This corrected the hang on my test setup, and OEM also confirmed that it corrected the problem for them. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Mailbox commands are polled for completion during ISP initialization. During potentially 'long' mailbox commands (i.e. fabric login), we really don't want a busy-wait delay to potentially trigger a (benign) soft-lockup BUG(). Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
There's no point in displaying the message during a valid underrun case. Limit the message to potentially problematic cases. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
The initial-control-block references are not always correct as the use-node-name qualifier during NVRAM configuration will cause the firmware to use the portname as a base for the nodename. Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
From: FUJITA Tomonori <tomof@acm.org> and zhenyu.z.wang@intel.com: We cannot handle filesystems like XFS becuase of the pages they are sending us. We had thought page_count could be used to work around this, but the correct test is for PageSlab. The proper solution is to figure out what type of pages filesystems can use so we do not have to add tests like this or handle it in the block layer for all network block drivers but the issue still has not been resolved on fs-devel so we are sending this patch as a temporary fix. This is last patch just in case it is Nakd with the explanation that we need to push the correct fix through fs-devel, mm or the block layer. The rest of the patchset can live without the patch, but the driver will not work with filesystems like XFS. Signed-off-by: NAlex Aizman <itn780@yahoo.com> Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
When we run the xmit code from queuecomand the stack trace gets too deep. The patch runs the xmit code from the scsi_host work queue. This fixes 4k stack and xfs support and should fix the st and sg stack usage bugs. Signed-off-by: NAlex Aizman <itn780@yahoo.com> Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
This is the second version of the patch to address Christoph's comments. Instead of doing the lib, I just kept everything in scsi_trnapsort_iscsi.c like the FC and SPI class. This was becuase the driver model and sysfs class is tied to the session and connection setup so separating did not buy very much at this time. The reason for this patch was becuase HW iscsi LLDs like qla4xxx cannot use the iscsi class becuase the scsi_host was tied to the interface and class code. This patch just seperates the session from scsi host so that LLDs that allocate the host per some resource like pci device can still use the class. This is also fixes a couple refcount bugs that can be triggered when users have a sysfs file open, close the session, then read or write to the file. Signed-off-by: NAlex Aizman <itn780@yahoo.com> Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-
由 Mike Christie 提交于
From Mike Christie <michaelc@cs.wisc.edu> and FUJITA Tomonori <tomof@acm.org>: We cannot use page_address becuase some pages could be highmem. Instead, we can use sock_no_sendpage which does kmap for us. Signed-off-by: NAlex Aizman <itn780@yahoo.com> Signed-off-by: NDmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
-