I noticed one of those and it turned out we have a few lingering around.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's handy to have debug message for the "big" events and this one
qualifies IMHO. Also helpful to see what's happening while we're loading
the firwmare and how much time it takes.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In Linux, macros are usually well done and protect their arguments
properly, even avoiding multiple evaluations of the parameters. Extra ()
are really not needed.

Cc: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only bit 27 of SCRATCH1 and bit 6 of ROW_CHICKEN3 are allowed to be
set because of security-sensitive bits we don't want userspace to mess
with.  On HSW hardware the whitelisted bits control whether atomic
read-modify-write operations are performed on L3 or on GTI, and when
set to L3 (which can be 10x-30x better performing than on GTI,
depending on the application) require great care to avoid a system
hang, so we currently program them to be handled on GTI by default.

Beignet can immediately start taking advantage of this change to
enable L3 atomics.  Mesa should eventually switch to L3 atomics too,
but a number of non-trivial changes are still required so it will
continue using GTI atomics for now.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Reviewed-by: NZhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In some cases it might be unnecessary or dangerous to give userspace
the right to write arbitrary values to some register, even though it
might be desirable to give it control of some of its bits.  This patch
extends the register whitelist entries to contain a mask/value pair in
addition to the register offset.  For registers with non-zero mask,
any LRM writes and LRI writes where the bits of the immediate given by
the mask don't match the specified value will be rejected.

This will be used in my next patch to grant userspace partial write
access to some sensitive registers.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Reviewed-by: NZhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Until now the software command checker assumed that commands could
read or write at most a single register per packet.  This is not
necessarily the case, MI_LOAD_REGISTER_IMM expects a variable-length
list of offset/value pairs and writes them in sequence.  The previous
code would only check whether the first entry was valid, effectively
allowing userspace to write unrestricted registers of the MMIO space
by sending a multi-register write with a legal first register, with
potential security implications on Gen6 and 7 hardware.

Fix it by extending the drm_i915_cmd_descriptor table to represent
multi-register access and making validate_cmd() iterate for all
register offsets present in the command packet.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Reviewed-by: NZhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Switch from using 31 PFI credits to 63 PFI credits when cdclk>=czclk on
CHV. The spec lists both 31 and 63 as "suggested" values, but based on
feedback from hardware folks we should actually be using 63. Originally
I picked the 31 basically by flipping a coin.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch fixes the resume from suspend-to-ram on the IBM X30
laptop. The problem is caused by the Bios missing to re-initialize
the iVCH registers, especially the PLL registers.

This patch records the iVCH registers during initialization, and
re-installs this register set when resuming.
Signed-off-by: NThomas Richter <thor@math.tu-berlin.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We are always allocating a single page. No need to be verbose so
remove the suffix.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Free the scratch page if dma mapping fails.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The divider value to convert from CZ clock rate to ms needs a +1
adjustment on VLV just like on CHV. This matches both the spec and
the accuracy test by pm_rc6_residency.

v2:
- simplify logic checking for the CHV 320MHz special case (Rodrigo)

Testcase: igt/pm_rc6_residency
Signed-off-by: NImre Deak <imre.deak@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76877Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we're forgetting to double the port clock when using double
clocked modes with 12bpc on HDMI. We're only accounting for the 1.5x
factor due to the 12bpc. So further double the 1.5x port clock when we
have a double clocked mode.

Unfortunately I don't have any displays that support both 12bpc and
double clocked modes, so I was unable to test this.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Account for the pixel multiplier when reading out the HDMI
mode dotclock. Makes the state checked happier on my ILK when using
double clocked modes.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Check that the DIP is enabled on the right port on IBX and VLV/CHV as
we're doing on g4x, and also check for all the infoframe enable bits on
all platforms.

Eventually we should track each infoframe type independently, and also
their contents. This is a small step in that direction as .infoframe_enabled()
return value could be easily turned into a bitmask.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we just disable the GCP infoframe when turning off the port.
That means if the same transcoder is used on a DP port next, we might
end up pushing infoframes over DP, which isn't intended. Just disable
all the infoframes when turning off the port.

Also protect against two ports stomping on each other on g4x due to
the single video DIP instance. Now only the first port to enable
gets to send infoframes.

v2: Rebase
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Follow the procedure listed in Bspec to toggle the port enable bit off
and on when enabling HDMI with 12bpc and pixel repeat on IBX. The old
code didn't actually enable the port before "toggling" the bit back off,
so the whole workaround was essentially a nop.

Also take the opportunity to clarify the code by splitting the gmch
platforms to a separate (much more straightforward) function.

v2: Rebased due to crtc->config changes
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

IBX BSpec says we must specify 8bpc in TRANSCONF for both 8bpc
and 12bpc HDMI output. Do so.

v2: Pass intel_crtc to intel_pipe_has_type()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When the video timings are suitably aligned so that all different
periods start at phase 0 (ie. none of the periods start mid-pixel)
we can inform the sink about this. Supposedly the sink can then
optimize certain things. Obviously this is only relevant when
outputting >8bpc data since otherwise there are no mid-pixel phases.

v2: Rebased due to crtc->config changes
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

GCP infoframes are required to inform the HDMI sink about the color
depth.

Send the GCP infoframe whenever the sink supports any deep color modes
since such sinks must anyway be capable of receiving them. For sinks
that don't support deep color let's skip the GCP in case it might
confuse the sink, although HDMI 1.4 spec does say all sinks must be
capable of reciving them. In theory we could skip the GCP infoframe
for deep color sinks in 8bpc mode as well since sinks must fall back to
8bpc whenever GCP isn't received for some time.

BSpec says we should disable GCP after disabling the port, so do that as
well.

v2: s/intel_set_gcp_infoframe/intel_hdmi_set_gcp_infoframe/
    Rebased due to crtc->config changes
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with lack of chv phy patches and fixup typo
Chandra spotted.]
Reviewed-by: NChandra Konduru <Chandra.konduru@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CPT/PPT require a specific procedure for enabling 12bpc HDMI. Implement
it, and to keep things neat pull the code into a function.

v2: Rebased due to crtc->config changes
    s/HDMI_GC/HDMIUNIT_GC/ to match spec better
    Factor out intel_enable_hdmi_audio()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-By: NChandra Konduru <Chandra.konduru@intel.com>
Testecase: igt/kms_render/*
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pull in patches Jani applied while I was on vacation.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

According to bspec the DDI PHY vswing scale value is "don't care" in
case the scale enable bit [27] is clear. But this doesn't seem to be
correct. The scale value seems to also matter if the scale mode bit
[26] is set. So both bit 26 and 27 depend on the value. Setting the
scale value to 0 while either bit is set results in a failed modeset on
HDMI (sink reports no signal).

After reset the scale value is 0x98, but according to the spec we have
to program it to 0x9a. So for consistency program it always to 0x9a
regardless of the scale enable bit.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Tested-by: NMatt Roper <matthew.d.roper@intel.com>
Acked-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Ville's and Mika's cdclk series was in flight at the same time as the
SKL S3 patches so we were missing that update.

intel_update_max_cdclk() and intel_update_cdclk() had to be moved up a
bit to avoid forward declarations.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

intel_update_cdclk() will already display the boot CDCLK for DDI
platforms, no need to repeat there.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

We can operate with DPLL0 off with CDCLK backed by the 24Mhz reference
clock, and that's a supported configuration. Don't warn when notice
DPLL0 is off then.

We still have a separate warn at boot if cdclk is disabled (because we
don't currently try to handle the case (that shouldn't happen on SKL as
far as I know) where we boot with display not initialized.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Add support for changing cdclk frequency during runtime on BDW.

Also with IPS enabled the actual pixel rate mustn't exceed 95% of cdclk,
so take that into account when computing the max pixel rate.

v2: Grab rps.hw_lock around sandybridge_pcode_write()
v3: Rebase due to power well vs. .global_resources() reordering
v4: Rebased to the latest
v5: Rebased to the latest
v6: Patch order shuffle so that Broadwell CD clock change is
    applied before the patch for Haswell CD clock change
v7: Fix for patch style problems
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

We need to tell BDW ULT and ULX apart.

v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Bspec says we shouldn't enable IPS on BDW when the pipe pixel rate
exceeds 95% of the core display clock. Apparently this can cause
underruns.

There's no similar restriction listed for HSW, so leave that one alone
for now.

v2: Add pipe_config_supports_ips() (Chris)
v3: Compare against the max cdclk insted of the current cdclk
v4: Rebased to the latest
v5: Rebased to the latest
v6: Fix for patch style problems

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83497Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Keep the cdclk maximum supported frequency around in dev_priv so that we
can verify certain things against it before actually changing the cdclk
frequency.

For now only VLV/CHV have support changing cdclk frequency, so other
plarforms get to assume cdclk is fixed.

v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Rather than reading out the current cdclk value use the cached value we
have tucked away in dev_priv.

v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Rather that extracting the current cdclk freuqncy every time someone
wants to know it, cache the current value and use that. VLV/CHV already
stored a cached value there so just expand that to cover all platforms.

v2: Rebased to the latest
v3: Rebased to the latest
v4: Rebased to the latest
v5: Removed spurious call to 'intel_update_cdclk(dev)' based on
    Damien Lespiau's comment
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Backmerge drm-next so I can apply Maarten's drm/i915 atomic conversion
patches.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Yay, thanks to Gerd for pull this together.

* 'virtio-gpu-drm-next' of git://git.kraxel.org/linux:
  Add MAINTAINERS entry for virtio-gpu.
  Add virtio gpu driver.
  drm_vblank_get: don't WARN_ON in case vblanks are not initialized
  break kconfig dependency loop

Please pull the contents of "Use DRM component API in tilcdc to
connect to tda998x" patch series.

* 'linux-4.1.0-rc5-tilcdc-refactor' of https://github.com/jsarha/linux:
  drm/tilcdc: Force building of DRM_TILCDC_SLAVE_COMPAT
  drm/tilcdc: Add DRM_TILCDC_SLAVE_COMPAT for ti,tilcdc,slave binding support
  drm/tilcdc: use pm_runtime_irq_safe()
  drm/tilcdc: Add support for external tda998x encoder
  drm/tilcdc: Remove tilcdc slave support for tda998x driver
  drm/tilcdc: Fix module unloading

Linux 4.1-rc6

backmerge 4.1-rc6 as some of the later pull reqs are based on newer bases
and I'd prefer to do the fixup myself.