1PPS (One Pulse Per Second) is a signal generated either
by the NIC PHC or an external timing source.
Integrating the support to configure and use 1PPS using
the TSIO pins along with PTP timestamps will add Grand
Master capability to the 5750X family chipsets.

This patch initializes the driver data structures and
registers the 1PPS with kernel, based on the TSIO pins'
capability in the hardware. This will create a /dev/ppsX
device which applications can use to receive PPS events.

Later patches will define functions to configure and use
the pins.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During error recovery or hot firmware upgrade, the chip may be under
reset and the PHC register read cycles may cause completion timeouts.
Check that the chip is not under reset condition before proceeding
to read the PHC by checking the flag BNXT_STATE_IN_FW_RESET.  We also
need to take the ptp_lock before we set this flag to prevent race
conditions.

We need this logic because the PHC now will stay registered after
bnxt_close().
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was pointed out by Richard Cochran that registering the PHC during
probe is better than during ifup, so move bnxt_ptp_init() back to
bnxt_init_one().  In order to work correctly after firmware reset which
may result in PTP config. changes, we modify bnxt_ptp_init() to return
if the PHC has been registered earlier.  If PTP is no longer supported
by the new firmware, we will unregister the PHC and clean up.

This partially reverts:

d7859afb ("bnxt_en: Move bnxt_ptp_init() to bnxt_open()")
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.

Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.

This is a purely cosmetic change intended to help readers find
their way through the implementation.

Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJason Gunthorpe <jgg@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current PTP initialization logic does not account for firmware
reset that may cause PTP capability to change.  The valid pointer
bp->ptp_cfg is used to indicate that the device is capable of PTP
and that it has been initialized.  So we must clean up bp->ptp_cfg
and free it if the firmware after reset does not support PTP.

Fixes: 93cb62d9 ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device needs to be in ifup state for PTP to function, so move
bnxt_ptp_init() to bnxt_open().  This means that the PHC will be
registered during bnxt_open().

This also makes firmware reset work correctly.  PTP configurations
may change after firmware upgrade or downgrade.  bnxt_open() will
be called after firmware reset, so it will work properly.

bnxt_ptp_start() is now incorporated into bnxt_ptp_init().  We now
also need to call bnxt_ptp_clear() in bnxt_close().

Fixes: 93cb62d9 ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock.  Firmware reset can be happening at the same
time.  Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock.  It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting.  In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is.  The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.

Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:

  bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
  Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
  ...
  Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
  Call trace:
  bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
  bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
  bnxt_self_test+0x2dc/0x390 [bnxt_en]
  ethtool_self_test+0xe0/0x1f8
  dev_ethtool+0x1744/0x22d0
  dev_ioctl+0x190/0x3e0
  sock_ioctl+0x238/0x480
  do_vfs_ioctl+0xc4/0x758
  ksys_ioctl+0x84/0xb8
  __arm64_sys_ioctl+0x28/0x38
  el0_svc_handler+0xb0/0x180
  el0_svc+0x8/0xc

Fixes: a1301f08 ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack.  The stack will hit WARN() if the protocol ID is unsupported.

Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.

Fixes: a196e96b ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When bnxt_open() fails in the firmware reset path, the driver needs to
gracefully abort, but it is executing code that should be invoked only
in the success path.  Define a function to abort FW reset and
consolidate all error paths to call this new function.

Fixes: dab62e7c ("bnxt_en: Implement faster recovery for firmware fatal error.")
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock.  If the flag is set, we need to abort.

Fixes: 230d1f0d ("bnxt_en: Handle firmware reset.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.

Fixes: 2151fe08 ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ETS proportions are presented to HWRM_QUEUE_COS2BW_CFG as minimum
bandwidth constraints. Thus, zero is a legal value for a given TC.
However, if all the other TCs sum up to 100%, then at least one
hardware queue will starve, resulting in guaranteed TX timeouts.
Reject such nonsensical configurations.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.

Fixes: 6316ea6d ("bnxt_en: Enable AER support.")
Signed-off-by: NKalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call bnxt_ptp_init() to initialize and register with the clock driver
to enable PTP support.  Call bnxt_ptp_free() to unregister and clean
up during shutdown.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setup the TXBD to enable TX timestamp if requested.  At TX packet DMA
completion, if we requested TX timestamp on that packet, we defer to
.do_aux_work() to obtain the TX timestamp from the firmware before we
free the TX SKB.

v2: Use .do_aux_work() to get the TX timestamp from firmware.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the RX packet is timestamped by the hardware, the RX completion
record will contain the lower 32-bit of the timestamp.  This needs
to be combined with the upper 16-bit of the periodic timestamp that
we get from the timer.  The previous snapshot in ptp->old_timer is
used to make sure that the snapshot is not ahead of the RX timestamp
and we adjust for wrap-around if needed.

v2: Make ptp->old_time read access safe on 32-bit CPUs.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From the bnxt_timer(), read the 48-bit hardware running clock
periodically and store it in ptp->current_time.  The previous snapshot
of the clock will be stored in ptp->old_time.  The old_time snapshot
will be used in the next patches to compute the RX packet timestamps.

v2: Use .do_aux_work() to read the timer periodically.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the clock APIs to set/get/adjust the hw clock, and the related
ioctls and ethtool methods.

v2: Propagate error code from ptp_clock_register().
    Add spinlock to serialize access to the timecounter.  The
    timecounter is accessed in process context and the RX datapath.
    Read the PHC using direct registers.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store PTP hardware info in a structure if hardware and firmware support PTP.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding the PTP related firmware interface is the main change.

There is also a name change for admin_mtu, requiring code fixup.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bnxt driver has rcu_read_lock()/rcu_read_unlock() pairs around XDP
program invocations. However, the actual lifetime of the objects referred
by the XDP program invocation is longer, all the way through to the call to
xdp_do_flush(), making the scope of the rcu_read_lock() too small. This
turns out to be harmless because it all happens in a single NAPI poll
cycle (and thus under local_bh_disable()), but it makes the rcu_read_lock()
misleading.

Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: NToke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/bpf/20210624160609.292325-9-toke@redhat.com

bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.

Fixes: 7c380918 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.")
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TQM fastpath ring needs to be sized to store both the requester
and responder side of RoCE QPs in TQM for supporting bi-directional
tests.  Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of
2 when computing the number of entries for TQM fastpath ring.  This
fixes an RX pipeline stall issue when running bi-directional max
RoCE QP tests.

Fixes: c7dd7ab4 ("bnxt_en: Improve TQM ring context memory sizing formulas.")
Signed-off-by: NRukhsana Ansari <rukhsana.ansari@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset.  This can cause
some PHY related functionalities to fail after a firmware reset.  For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.

Fixes: ec5d31e3 ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>

There was a typo in the code that checks for 64K BNXT_PAGE_SHIFT in
bnxt_hwrm_set_pg_attr().  Fix it and make the code more understandable
with a new macro BNXT_SET_CTX_PAGE_ATTR().

Fixes: 1b9394e5 ("bnxt_en: Configure context memory on new devices.")
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise, some of the recently added HyperV VF IDs would not be
recognized as VF devices and they would not initialize properly.

Fixes: 7fbf359b ("bnxt_en: Add PCI IDs for Hyper-V VF devices.")
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski pointed out that we need to handle ipv6 extension headers
and to explicitly check for supported tunnel types in
.ndo_features_check().

For ipv6 extension headers, the hardware supports up to 2 ext. headers
and each must be <= 64 bytes.  For tunneled packets, the supported
packets are UDP with supported VXLAN and Geneve ports, GRE, and IPIP.

v3: More improvements based on Alexander Duyck's valuable feedback -
    Remove the jump lable in bnxt_features_check() and restructure it
    so that the TCP/UDP is check is consolidated in bnxt_exthdr_check().

v2: Add missing step to check inner ipv6 header for UDP and GRE tunnels.
    Check TCP/UDP next header after skipping ipv6 ext headers for
    non-tunneled packets and for inner ipv6.
    (Both feedback from Alexander Duyck)
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Fixes: 1698d600 ("bnxt_en: Implement .ndo_features_check().")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Reviewed-by: NAlexander Duyck <alexanderduyck@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All callers pass 0 as offset. Therefore remove the parameter and use a
fixed offset 0 in pci_vpd_find_tag().

Link: https://lore.kernel.org/r/f62e6e19-5423-2ead-b2bd-62844b23ef8f@gmail.comSigned-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

For UDP encapsultions, we only support the offloaded Vxlan port and
Geneve port.  All other ports included FOU and GUE are not supported so
we need to turn off TSO and checksum features.

v2: Reverse the check for supported UDP ports to be more straight forward.
Reviewed-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If firmware is capable, set the IFF_SUPP_NOFCS flag to support the
sockets option to transmit packets without FCS.  This is mainly used
for testing.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support VF device IDs used by the Hyper-V hypervisor.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the PF is no longer enforcing an assigned MAC address on a VF, the
VF needs to call bnxt_approve_mac() to tell the PF what MAC address it is
now using.  Otherwise it gets out of sync and the PF won't know what
MAC address the VF wants to use.  Ultimately the VF will fail when it
tries to setup the L2 MAC filter for the vnic.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move it before bnxt_update_vf_mac().  In the next patch, we need to call
bnxt_approve_mac() from bnxt_update_mac() under some conditions.  This
will avoid forward declaration.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is perfectly legal for the stack to query and configure VFs via PF
NDOs while the NIC is administratively down.  Remove the unnecessary
check for the PF to be in open state.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware previously only allowed promiscuous mode for VFs associated with
a default VLAN. It is now possible to enable promiscuous mode for a VF
having no VLAN configured provided that it is trusted. In such cases the
VF will see all packets received by the PF, irrespective of destination
MAC or VLAN.

Note, it is necessary to query firmware at the time of bnxt_promisc_ok()
instead of in bnxt_hwrm_func_qcfg() because the trusted status might be
altered by the PF after the VF has been configured. This check must now
also be deferred because the firmware call sleeps.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current code, the driver will not shutdown the link during
IFDOWN if there are still VFs sharing the port.  Newer firmware will
manage the link down decision when the port is shared by VFs, so
we can just call firmware to shutdown the port unconditionally and
let firmware make the final decision.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Copy the phy related feature flags from the firmware call
HWRM_PORT_PHY_QCAPS to this new field.  We can also remove the flags
field in the bnxt_test_info structure.  It's cleaner to have all PHY
related flags in one location, directly copied from the firmware.

To keep the BNXT_PHY_CFG_ABLE() macro logic the same, we need to make
a slight adjustment to check that it is a PF.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware reports link signalling mode for certain speeds. In these
cases, print the signalling modes in kernel log link up messages.
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_rx_pkt(), the RX buffers are expected to complete in order.
If the RX consumer index indicates an out of order buffer completion,
it means we are hitting a hardware bug and the driver will abort all
remaining RX packets and reset the RX ring.  The RX consumer index
that we pass to bnxt_discard_rx() is not correct.  We should be
passing the current index (tmp_raw_cons) instead of the old index
(raw_cons).  This bug can cause us to be at the wrong index when
trying to abort the next RX packet.  It can crash like this:

 #0 [ffff9bbcdf5c39a8] machine_kexec at ffffffff9b05e007
 #1 [ffff9bbcdf5c3a00] __crash_kexec at ffffffff9b111232
 #2 [ffff9bbcdf5c3ad0] panic at ffffffff9b07d61e
 #3 [ffff9bbcdf5c3b50] oops_end at ffffffff9b030978
 #4 [ffff9bbcdf5c3b78] no_context at ffffffff9b06aaf0
 #5 [ffff9bbcdf5c3bd8] __bad_area_nosemaphore at ffffffff9b06ae2e
 #6 [ffff9bbcdf5c3c28] bad_area_nosemaphore at ffffffff9b06af24
 #7 [ffff9bbcdf5c3c38] __do_page_fault at ffffffff9b06b67e
 #8 [ffff9bbcdf5c3cb0] do_page_fault at ffffffff9b06bb12
 #9 [ffff9bbcdf5c3ce0] page_fault at ffffffff9bc015c5
    [exception RIP: bnxt_rx_pkt+237]
    RIP: ffffffffc0259cdd  RSP: ffff9bbcdf5c3d98  RFLAGS: 00010213
    RAX: 000000005dd8097f  RBX: ffff9ba4cb11b7e0  RCX: ffffa923cf6e9000
    RDX: 0000000000000fff  RSI: 0000000000000627  RDI: 0000000000001000
    RBP: ffff9bbcdf5c3e60   R8: 0000000000420003   R9: 000000000000020d
    R10: ffffa923cf6ec138  R11: ffff9bbcdf5c3e83  R12: ffff9ba4d6f928c0
    R13: ffff9ba4cac28080  R14: ffff9ba4cb11b7f0  R15: ffff9ba4d5a30000
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018

Fixes: a1b0e4e6 ("bnxt_en: Improve RX consumer index validity check.")
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>