Add a mipi_dsi node, and also add mipi_dsi endpoints to vopb and vopl
output port nodes.
Signed-off-by: NChris Zhong <zyw@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The current vdd_arm voltage is too low, increase it will make
the system more stable.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Rayeager/Bqcurie2/Marsboard use pwm3 modulate the vdd_logic voltage,
so enable it.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Although We can add the sdmmc node, shouldn't enable it.
Since the sdmmc is reusing the same pin with uart2.
Unfortunately, the uart2 is used by the debug port, so that will cause
the debug information can't display on console if enabling the sdmmc.

As we have supported the sdmmc (sd card) on hardware for kylin board.
So, maybe we can have the sdmmc node in kylin dts, not to enable it.

Anyway, you only need add the okay status if someone want to enable the
sdmmc.

e.g.
if you use the adb to debug with android os.
You can add the
status = "okay" to enable the sdmmc for sd card working.
The default status is disabling it.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This patch adds the sdio power sequence for kylin board.
The WLAN attached to a SDIO interface, wifi/bluetooth have
reset and power been needed to enable.

AFAIK, the simple power sequence provider sets a value for multiple GPIOs.
So the reset and power of WlAN chip can be handled in mmc power sequence.
On the module itself this is one of these, that should can be handled
by reset GPIOs in simple mmc power sequence.

The Bluetooth host wake is high active from bootup, this patch is also
set pinctrl bias as the default to enable the pull up in soc internal.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

We want to the higher speed for wifi module working.

Bootup kernel log:
...
mmc_host mmc0: Bus speed (slot 0) = 37125000Hz (slot req 37500000Hz,
actual 37125000HZ div = 0)

or run 'cat /sys/kernel/debug/clk/clk_summary |grep phase -C 1' to check
Otherwise, the mmc0 will run 400khz defalult value to work.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This patch is enabling the uart0 for bluetooth module.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Describe the two user-controllable LEDs on Rock2 Square boards.
All information have been retrieved from the schematics and the vendor
devicetree. The default-triggers mimic the behaviour of the vendor-kernel to
keep functionalities in sync.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Reviewed-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The rk3036-kylin board uses a rt5616 audio codec connected to the i2s
and can use the simple card to tie everyting together.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

For sound setups using the simple-card mechanism, the main clock
(sysclk) is expected to be the first element. For the i2s-driver
itself it doesn't matter, as it uses named clocks, so we can just
swap them.
Reported-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Sometime will hang if you set the i2s pinctrl as the none setting.
Let's set the pinctrl as the default setting to enable the gpio bias.
Signed-off-by: NCaesar Wang <wxt@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.

When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Allow BMIPS_GENERIC supported platforms to build GPIO controller
drivers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NDragan Stancevic <dragan.stancevic@gmail.com>
Cc: cernekee@gmail.com
Cc: jaedon.shin@gmail.com
Cc: gregory.0xf0@gmail.com
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12019/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove bcm63xx_nvram_get_psi_size() as it now has no users.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11836/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move Broadcom BCM963xx image tag data structure to include/linux/
so that drivers outside of mach-bcm63xx can use it.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11832/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use the common definition of the nvram structure from the header file
include/linux/bcm963xx_nvram.h instead of maintaining a separate copy.

Read the version 5 size of nvram data from memory and then call the
new checksum verification function from the header file.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11831/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add missing newline to end of kvm_err string when guest PMAP couldn't be
allocated.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11896/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.

Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11895/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Drop the custom cache operation code definitions used by KVM for
emulating guest CACHE instructions, and switch to use the existing
definitions in <asm/cacheops.h>.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11893/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Most of the cache op codes defined in cacheops.h are split into a 2-bit
cache identifier, and a 3-bit cache op code which does largely the same
thing semantically regardless of the cache identifier.

To allow the use of these definitions by KVM for decoding cache ops,
break the definitions down into parts where it makes sense to do so, and
add masks for the Cache and Op field within the cache op.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11892/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The first argument to set_except_vector is the ExcCode, which we now
have definitions for. Lets make use of them.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11894/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a few missing trap codes.

[ralf@linux-mips.org: Drop removal of exception codes.  I don't care what
the incomplete architecture spec says; it can't change existing hardware
and VCEI is supported indeed.]
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11890/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the Cause.ExcCode trap code definitions from kvm_host.h to
mipsregs.h, since they describe architectural bits rather than KVM
specific constants, and change the prefix from T_ to EXCCODE_.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11891/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The module init and exit functions have no need to be global, so make
them static.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11889/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When calculating the offsets into the commpage for dynamically
translated mtc0/mfc0 guest instructions, multiple offsetof()s are added
together to find the offset of the specific register in the mips_coproc,
within the commpage.

Simplify each of these cases to a single offsetof() to find the offset
of the specific register within the commpage.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11888/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Export symbols only to GPL modules to match other KVM symbols in
virt/kvm/ and arch/*/kvm/.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11887/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The function kvm_mips_host_tlb_inv_index() is unused, so drop it
completely.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11886/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The CAUSEB_DC and CAUSEF_DC definitions used by KVM are defined in
asm/kvm_host.h, but all the other Cause register field definitions are
found in asm/mipsregs.h.

Lets reunite the DC bit definitions with its friends in mipsregs.h.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11885/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Some definitions in the MIPS asm/kvm_host.h are completely unused, so
lets drop them.

MS_TO_NS is no longer used since commit e30492bb ("MIPS: KVM:
Rewrite count/compare timer emulation"). The others don't appear ever to
have been used.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11884/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

A bunch of misc whitespace and style fixes within arch/mips/kvm/.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11883/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds an initial default config that enables all available PIC32
drivers and is enough for booting a PIC32MZDA Starter Kit.
Signed-off-by: NJoshua Henderson <joshua.henderson@microchip.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12105/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds basic DTS configuration for the PIC32MZDA chip and in turn the
PIC32MZDA Starter Kit.
Signed-off-by: NJoshua Henderson <joshua.henderson@microchip.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12104/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds support for the Microchip PIC32 MIPS microcontroller with the
specific variant PIC32MZDA. PIC32MZDA is based on the MIPS m14KEc core
and boots using device tree.

This includes an early pin setup and early clock setup needed prior to
device tree being initialized. In additon, an interface is provided to
synchronize access to registers shared across several peripherals.
Signed-off-by: NJoshua Henderson <joshua.henderson@microchip.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12097/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add brcm,bcm6358-leds node to bcm6368.dtsi
Add reboot support (syscon-reboot as defined in BCM6328)
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/12117/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds bcm6328-leds node to bcm6328.dtsi
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/12116/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The cp0_tcstatus member of struct pt_regs was removed along with the
rest of SMTC in v3.16, commit b633648c ("MIPS: MT: Remove SMTC
support"), however recent uprobes support in v4.3 added back a reference
to it in the regoffset_table[] in ptrace.c. Remove it.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Fixes: 40e084a5 ("MIPS: Add uprobes support.")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11920/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11925/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11924/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11923/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>