The 5709 Serdes device uses non-standard MII register offsets.  This
re-structuring will make it easier to support 5709 Serdes.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is needed to save the MSI state which will be lost during
suspend.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

    
Hot-plug scripts can call bnx2_open() as soon as register_netdev() is
called in bnx2_init_one().  We need to call pci_set_drvdata() and
setup everything before calling register_netdev(). netif_carrier_off()
also needs to be moved to bnx2_open() to avoid race conditions with
the irq.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The internal PCIE-to-PCIX bridge of the 5708 has the same 40-bit DMA
limitation as some of the tg3 chips.  Set dma_mask and persistent DMA
mask to 40-bit to workaround.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tweak registers and memory test range for 5709.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device may be in D3hot state and should not allow MII register
access.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.

Ditched a no-op in bnx2 in the process.

I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...

Just out of curiosity, here are the idioms found to get the same result:

skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tweak a register setting to prevent the tx mailbox from halting.

Update version to 1.5.8.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The nvram dword alignment logic was broken when writing less than 4
bytes on a non-aligned offset.  It was missing logic to round the
length to 4 bytes.

The page erase code is also moved so that it is only called when
using non-buffered flash for better code clarity.

Update version to 1.5.7.

Based on initial patch from Tony Cureington <tony.cureington@hp.com>.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2_has_work()'s logic is flawed and can cause the driver to miss
a link event.  The fix is to compare the status block's attn_bits
and attn_bits_ack to determine if there is a link event.

Update version to 1.5.6.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.

I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: NDan Aloni <da-x@monatomic.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I don't see any reason why we need pci_msi_quirk, quirk code can just
call pci_no_msi() instead.

Remove the check of pci_msi_quirk in msi_init(). This is safe as all
calls to msi_init() are protected by calls to pci_msi_supported(),
which checks pci_msi_enable, which is disabled by pci_no_msi().

The pci_disable_msi routines didn't check pci_msi_quirk, only
pci_msi_enable, but as far as I can see that was a bug not a feature.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since it's no longer used, this "#define BCM_TSO 1" can now be removed.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove the NETIF_F_TSO #ifdef-ery in drivers/net; this was
for old-old-2.4 compat (even current 2.4 has NETIF_F_TSO)
but it's time to get rid of it by now.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

5709 A0 copper devices will not link up with some link partners
without this workaround.

Update driver to 1.5.5.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the 5709, we need to add the proper offset to calculate the shared
memory base address of the 2nd port correctly.  Otherwise, the 2nd
port's MAC address and other information will be the same as the 1st
port.

Update version to 1.5.4.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 1.5.3.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bug was a bogus pointer being passed to kfree().  The pointer was
incremented in the write loop and then passed to kfree().

The fix is to use align_buf to save the original address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5709 has a new register to detect copper/fiber PHYs.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workaround is only needed on 5706/5708 and cannot be applied on
5709.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the configured MAC address instead of the permanent MAC address
for loopback frames.

Update version to 1.5.2.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Length was not calculated correctly if the NVRAM offset is on a non-
aligned offset.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was an off-by-one bug in bnx2_tx_avail().  If the tx ring is
completely full, the producer and consumer indices may be apart by
256 even though the ring size is only 255.  One entry in the ring is
unused and must be properly accounted for when calculating the number
of available entries.  The bug caused the tx ring entries to be
reused by mistake, overwriting active entries, and ultimately causing
it to crash.

This bug rarely occurs because the tx ring is rarely completely full.
We always stop when there is less than MAX_SKB_FRAGS entries available
in the ring.

Thanks to Corey Kovacs <cjk@techma.com> and Andy Gospodarek
<agospoda@redhat.com> for reporting the problem and helping to collect
debug information.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a missing error check spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 1.5.1.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add PCI ID and detection for 5709 copper and SerDes chips.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic support to initialize the 5709 chip.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-organize the firmware handling code and declarations a bit to make
the code more compact.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change a long udelay() in bnx2_setup_copper_phy() to msleep().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to parallel detect 1Gbps and 2.5Gbps link speeds.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate the 5706S SerDes handling code in bnx2_timer() and put it
in a new function.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Add support for 2.5Gbps forced speed setting.
2. Remove a long udelay() loop and change to msleep().
3. Other misc. SerDes fixes.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the problem of not receiving packets in the Xen bridging
environment.  The Xen script sets the device's MAC address to
FE:FF:FF:FF:FF:FF and puts the device in promiscuous mode.  The
firmware had problem receiving all packets in this configuration.

New firmware and setting the PROM_VLAN bit when in promiscuous mode
will fix this problem.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>