This patch adds support for the AMCC (AppliedMicro) PPC460SX Eiger evaluation
board.
Signed-off-by: NTai Tri Nguyen <ttnguyen@amcc.com>
Acked-by: NFeng Kan <fkan@amcc.com>
Acked-by: NTirumala Marri <tmarri@amcc.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NRoderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

It is common to use U-Boot on Xilinx Virtex platforms.  This patch
ensures that CONFIG_DEFAULT_UIMAGE is selected for virtex
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch contains initial framework for the AMCC Redwood board.
Signed-off-by: NMadhulika Madishetty <mmadishetty@amcc.com>
Signed-off-by: NTirumala Marri <tmarri@amcc.com>
Signed-off-by: NFeng Kan <fkan@amcc.com>
Signed-off-by: NVidhyananth Venkatasamy <vvenkatasamy@amcc.com>
Signed-off-by: NPreetesh Parekh <pparekh@amcc.com>
Acked-by: NLoc Ho <lho@amcc.com>
Acked-by: NFeng Kan <fkan@amcc.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds support for the GPIO functions of PPC40x and PPC44x
SOCs.
Signed-off-by: NSteve Falco <sfalco@harris.com>
Acked-by: NStefan Roese <sr@denx.de>
Acked-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications.  Each 460GT has it's own 512MB DDR2 memory, 32MB NOR FLASH,
UART, EEPROM and temperature sensor, along with a shared debug port.
The two 460GT's will communicate with each other via shared memory,
Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: NVictor Gallardo <vgallardo@amcc.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add explicit support for the AMCC Glacier eval board to Kconfig and the
ppc44x_simple file.  Also removes the cayonlands compatible entry from the
DTS file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Migrate the AMCC Taishan board to use the ppc44x_simple platform file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Migrate the AMCC Sequoia board to use the ppc44x_simple platform file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Migrate the AMCC Rainier board to use the ppc44x_simple platform file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Migrate the AMCC Katmai board to use the ppc44x_simple platform file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Migrate the AMCC Canyonlands board to use the ppc44x_simple platform file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Migrate the AMCC Bamboo board to use the ppc44x_simple platform file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds a common board file for almost all of the "simple" PowerPC 44x
boards that exist today.  This is intended to be a single place to add
support for boards that do not differ in platform support from most of the
evaluation boards that are used as reference platforms.  Boards that have
specific requirements or custom hardware setup should still have their own
board.c file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Support for the Xilinx Virtex5 FXT 440 is being added.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.

It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: NGiuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch creates a common system reset routine for all 40x and 44x
systems. Previously only a 44x routine existed. But since this system
reset via the debug control register is common for 40x and 44x let's
share this code for all those platforms in ppc4xx_soc.c.

This patch also enables CONFIG_4xx_SOC for all 40x and 44x platforms.

Tested on Kilauea (405EX) and Canyonlands (440EX).
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds support for the 256k L2 cache found on some IBM/AMCC
4xx PPC's. It introduces a common 4xx SoC file (sysdev/ppc4xx_soc.c)
which currently "only" adds the L2 cache init code. Other common 4xx
stuff can be added later here.

The L2 cache handling code is a copy of Eugene's code in arch/ppc
with small modifications.

Tested on AMCC Taishan 440GX.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The AMCC 440EP Yosemite board is very similar to the original AMCC Bamboo
board.  This adds a YOSEMITE option to Kconfig, and reuses the existing
bamboo board support in the kernel.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Canyonlands is the AMCC 460EX eval board, featuring nearly all of the 460EX
interfaces:

- 1 * PCI (max 66MHz), 2 * PCIe (one 4-lane, one 1-lane)
- 2 * GBit Ethernet with TCP/IP acceleration
- USB 2.0 Host/Device OTG and Host interface
- SATA port
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Clean up some whitespace issues in the 44x Kconfig file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add the base platform support for the PIKA Warp boards.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards.  The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.

Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
	http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.

This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented.  That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Enable PCI support for these eval boards among other things.  Also selects
PCI for Rainier in the Kconfig file.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

PowerPC 440GRx Rainier board support.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds the device-tree bits & call to ppc4xx_pci_find_bridges()
to make PCI work on the Bamboo board
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds base support for the AMCC Taishan 440GX evaluation
board.
Signed-off-by: NHugh Blemings <hugh@blemings.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This wires up the 4xx PCI support & device tree bits for
440GP based Ebony platform.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds a cputable function pointer for the CPU-side machine
check handling. The semantic is still the same as the old one,
the one in ppc_md. overrides the one in cputable, though
ultimately we'll want to change that so the CPU gets first.

This removes CONFIG_440A which was a problem for multiplatform
kernels and instead fixes up the IVOR at runtime from a setup_cpu
function. The "A" version of the machine check also tweaks the
regs->trap value to differenciate the 2 versions at the C level.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Fix some device tree omissions that prevented the new EMAC driver from
setting up ethernet on the Bamboo board correctly and update the Bamboo
defconfig.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch enables NEW EMAC support for PowerPC 440EPx Sequoia board.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds RGMII support to Sequoia DTS and sets correct phy-mode
for EMACs. According to Sequoia datasheet, both ethernet ports
are connected to RGMII interface, while ZMII is used only for MDIO.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.

This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).

This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

AMCC PPC440EPx Sequoia board support.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add support for the AMCC Bamboo board
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>

An allmodconfig on the current powerpc tree yields:
arch/powerpc/platforms/44x/Kconfig:41:warning: 'select' used by
config symbol '440GP' refers to undefined symbol 'IBM_NEW_EMAC_ZMII'

Hide the select until the driver exists.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds platform support code for the Ebony (440GP) evaluation
board.  This includes both code in arch/powerpc/platforms/44x for
board initialization, and zImage wrapper code to correctly tweak the
flattened device tree based on information from the firmware.  The
zImage supports both IBM OpenBIOS (aka "treeboot") and old versions of
uboot which don't support a flattened device tree.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>