Skip to content

K
Kernel

openeuler / Kernel
大约 1 年 前同步成功

通知 5
Star 0
Fork 0
K
Kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 12 6月, 2010 4 次提交
    • R
      ACPI / ACPICA: Avoid writing full enable masks to GPE registers · c9a8bbb7
      由 Rafael J. Wysocki 提交于 
      ACPICA uses acpi_hw_write_gpe_enable_reg() to re-enable a GPE after
an event signaled by it has been handled.  However, this function
writes the entire GPE enable mask to the GPE's enable register which
may not be correct.  Namely, if one of the other GPEs in the same
register was previously enabled by acpi_enable_gpe() and subsequently
disabled using acpi_set_gpe(), acpi_hw_write_gpe_enable_reg() will
re-enable it along with the target GPE.

To fix this issue rework acpi_hw_write_gpe_enable_reg() so that it
calls acpi_hw_low_set_gpe() with a special action value,
ACPI_GPE_COND_ENABLE, that will make it only enable the GPE if the
corresponding bit in its register's enable_for_run mask is set.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>
      c9a8bbb7
    • R
      ACPI / ACPICA: Fix low-level GPE manipulation code · fd247447
      由 Rafael J. Wysocki 提交于 
      ACPICA uses acpi_ev_enable_gpe() for enabling GPEs at the low level,
which is incorrect, because this function only enables the GPE if the
corresponding bit in its enable register's enable_for_run mask is set.
This causes acpi_set_gpe() to work incorrectly if used for enabling
GPEs that were not previously enabled with acpi_enable_gpe().  As a
result, among other things, wakeup-only GPEs are never enabled by
acpi_enable_wakeup_device(), so the devices that use them are unable
to wake up the system.

To fix this issue remove acpi_ev_enable_gpe() and its counterpart
acpi_ev_disable_gpe() and replace acpi_hw_low_disable_gpe() with
acpi_hw_low_set_gpe() that will be used instead to manipulate GPE
enable bits at the low level.  Make the users of acpi_ev_enable_gpe()
and acpi_ev_disable_gpe() call acpi_hw_low_set_gpe() instead and
make sure that GPE enable masks are only updated by acpi_enable_gpe()
and acpi_disable_gpe() when GPE reference counters change from 0
to 1 and from 1 to 0, respectively.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>
      fd247447
    • R
      ACPI / ACPICA: Use helper function for computing GPE masks · e4e9a735
      由 Rafael J. Wysocki 提交于 
      In quite a few places ACPICA needs to compute a GPE enable mask with
only one bit, corresponding to a given GPE, set.  Currently, that
computation is always open coded which leads to unnecessary code
duplication.  Fix this by introducing a helper function for computing
one-bit GPE enable masks and using it where appropriate.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLen Brown <len.brown@intel.com>
      e4e9a735
    • R
      ACPI / ACPICA: Do not attempt to disable GPE when installing handler · a997ab33
      由 Rafael J. Wysocki 提交于 
      Commit 0f849d2c (ACPICA: Minimize
the differences between linux GPE code and ACPICA code base)
introduced a change attempting to disable a GPE before installing
a handler for it in acpi_install_gpe_handler() which was incorrect.
First, the GPE disabled by it is never enabled again (except during
resume) which leads to battery insert/remove events not being
reported on the Maxim Levitsky's machine.  Second, the disabled
GPE is still reported as enabled by the sysfs interface that only
checks its enable register's enable_for_run mask.

Revert this change for now, because it causes more damage to happen
than the bug it was supposed to fix.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
      a997ab33
  3. 20 4月, 2010 22 次提交
  5. 19 4月, 2010 14 次提交