Convert the XDP xmit functions to use the generic xdp_frame API
in XDP_TX flow.
Same functions will be used later in this series to transmit
the XDP redirect-out packets as well.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add per-ring and total stats for received packets that
goes into XDP redirection.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Take XDP code out of the general EN header and RX file into
new XDP files.

Currently, XDP-SQ resides only within an RQ and used from a
single flow (XDP_TX) triggered upon RX completions.
In a downstream patch, additional type of XDP-SQ instances will be
presented and used for the XDP_REDIRECT flow, totally unrelated to
the RX context.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add checks in control path upon an MTU change or an XDP program set,
to prevent reaching cases where large MTU and XDP are set simultaneously.

This is to make sure we allow XDP only with the linear RX memory scheme,
i.e. a received packet is not scattered to different pages.
Change mlx5e_rx_get_linear_frag_sz() accordingly, so that we make sure
the XDP configuration can really be set, instead of assuming that it is.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Dedicate a function to all checks done when setting an XDP program.
Take indications from priv instead of netdev features.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Keep all page-pool recycle calls within NAPI context.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

No need to expose the MPWQE free function to control path.
The dealloc function already exposed, use it.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2018-07-26

This series contains updates to ixgbe and igb.

Tony fixes ixgbe to add checks to ensure jumbo frames or LRO get enabled
after an XDP program is loaded.

Shannon Nelson adds the missing security configuration registers to the
ixgbe register dump, which will help in debugging.

Christian Grönke fixes an issue in igb that occurs on SGMII based SPF
mdoules, by reverting changes from 2 previous patches.  The issue was
that initialization would fail on the fore mentioned modules because the
driver would try to reset the PHY before obtaining the PHY address of
the SGMII attached PHY.

Venkatesh Srinivas replaces wmb() with dma_wmb() for doorbell writes,
which avoids SFENCEs before the doorbell writes.

Alex cleans up and refactors ixgbe Tx/Rx shutdown to reduce time needed
to stop the device.  The code refactor allows us to take the completion
time into account when disabling queues, so that on some platforms with
higher completion times, would not result in receive queues disabled
messages.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Once user manually deletes the chain using "chain del", the chain cannot
be marked as explicitly created anymore.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Fixes: 32a4f5ec ("net: sched: introduce chain object to uapi")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The zerocopy path ultimately calls iov_iter_get_pages, which defines the
step function for ITER_KVECs as simply, return -EFAULT. Taking the
non-zerocopy path for ITER_KVECs avoids the unnecessary fallback.

See https://lore.kernel.org/lkml/20150401023311.GL29656@ZenIV.linux.org.uk/T/#u
for a discussion of why zerocopy for vmalloc data is not a good idea.

Discovered while testing NBD traffic encrypted with ktls.

Fixes: c46234eb ("tls: RX path for ktls")
Signed-off-by: NDoron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code at line 1850 is unreachable. Fix this by removing the break
statement above it, so the code for case RTM_GETCHAIN can be
properly executed.

Addresses-Coverity-ID: 1472050 ("Structurally dead code")
Fixes: 32a4f5ec ("net: sched: introduce chain object to uapi")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tunnel reception hook is only used by l2tp_ppp for skipping PPP
framing bytes. This is a session specific operation, but once a PPP
session sets ->recv_payload_hook on its tunnel, all frames received by
the tunnel will enter pppol2tp_recv_payload_hook(), including those
targeted at Ethernet sessions (an L2TPv3 tunnel can multiplex PPP and
Ethernet sessions).

So this mechanism is wrong, and uselessly complex. Let's just move this
functionality to the pppol2tp rx handler and drop ->recv_payload_hook.
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when tipc_own_id failed to obtain node identity,dev_put should
be call before return -EINVAL.

Fixes: 682cd3cf ("tipc: confgiure and apply UDP bearer MTU on running links")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed checks against non-NULL before calling kfree_skb() and
crypto_free_aead(). These functions are safe to be called with NULL
as an argument.
Signed-off-by: NVakul Garg <vakul.garg@nxp.com>
Acked-by: NDave Watson <davejwatson@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow to install a child qdisc under cbs. The main use case
is to install ETF (Earliest TxTime First) qdisc under cbs, so there's
another level of control for time-sensitive traffic.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:73:20: warning: symbol 'hns_ae_get_handle' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:332:6: warning: symbol 'hns_ae_stop' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:360:6: warning: symbol 'hns_ae_toggle_ring_irq' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:580:6: warning: symbol 'hns_ae_update_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:663:6: warning: symbol 'hns_ae_get_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:695:6: warning: symbol 'hns_ae_get_strings' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:728:5: warning: symbol 'hns_ae_get_sset_count' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:774:6: warning: symbol 'hns_ae_update_led_status' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:786:5: warning: symbol 'hns_ae_cpld_set_led_id' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:798:6: warning: symbol 'hns_ae_get_regs' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:823:5: warning: symbol 'hns_ae_get_regs_len' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c:342:6: warning: symbol 'hns_gmac_update_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:934:12: warning: symbol 'hns_mac_get_vaddr' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:953:5: warning: symbol 'hns_mac_get_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:343:6: warning: symbol 'hns_dsaf_srst_chns' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:366:1: warning: symbol 'hns_dsaf_srst_chns_acpi' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:373:6: warning: symbol 'hns_dsaf_roce_srst' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:387:6: warning: symbol 'hns_dsaf_roce_srst_acpi' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:571:5: warning: symbol 'hns_mac_get_sfp_prsnt' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:589:5: warning: symbol 'hns_mac_get_sfp_prsnt_acpi' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:31:12: warning: symbol 'g_dsaf_mode_match' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:45:5: warning: symbol 'hns_dsaf_get_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:962:6: warning: symbol 'hns_dsaf_tcam_addr_get' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:2087:6: warning: symbol 'hns_dsaf_port_work_rate_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:2837:5: warning: symbol 'hns_dsaf_roce_reset' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:76:5: warning: symbol 'hns_ppe_common_get_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:107:6: warning: symbol 'hns_ppe_common_free_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:340:6: warning: symbol 'hns_ppe_uninit_ex' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c:708:5: warning: symbol 'hns_rcb_get_ring_num' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c:744:14: warning: symbol 'hns_rcb_common_get_vaddr' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:314:6: warning: symbol 'hns_xgmac_update_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1303:6: warning: symbol 'hns_nic_update_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1585:6: warning: symbol 'hns_nic_poll_controller' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1938:6: warning: symbol 'hns_set_multicast_list' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1960:6: warning: symbol 'hns_nic_set_rx_mode' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:661:6: warning: symbol 'hns_get_ringparam' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:811:6: warning: symbol 'hns_get_channels' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:828:6: warning: symbol 'hns_get_ethtool_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:886:6: warning: symbol 'hns_get_strings' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:976:5: warning: symbol 'hns_get_sset_count' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:1010:5: warning: symbol 'hns_phy_led_set' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:1032:5: warning: symbol 'hns_set_phys_id' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:1106:6: warning: symbol 'hns_get_regs' was not declared. Should it be static?
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the tls binary to .gitignore

Fixes: 7f657d5b ("selftests: tls: add selftests for TLS sockets")
Signed-off-by: NAnders Roxell <anders.roxell@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is meant to allow us to take completion time into account when
disabling queues. Previously we were just working with hard coded values
for how long we should wait. This worked fine for the standard case where
completion timeout was operating in the 50us to 50ms range, however on
platforms that have higher completion timeout times this was resulting in
Rx queues disable messages being displayed as we weren't waiting long
enough for outstanding Rx DMA completions.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NDon Buchholz <donald.buchholz@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to help reduce the time needed to shutdown the
transmit and receive paths for the device. Specifically what we now do
after this patch is disable the transmit path first at the netdev level,
and then work on disabling the Rx. This way while we are waiting on the Rx
queues to be disabled the Tx queues have an opportunity to drain out.

In addition I have dropped the 10ms timeout that was left in the ixgbe_down
function that seems to have been carried through from back in e1000 as far
as I can tell. We shouldn't need it since we don't actually disable the Tx
until much later and we have additional logic in place for verifying the Tx
queues have been disabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NDon Buchholz <donald.buchholz@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

igb writes to doorbells to post transmit and receive descriptors;
after writing descriptors to memory but before writing to doorbells,
use dma_wmb() rather than wmb(). wmb() is more heavyweight than
necessary before doorbell writes.

On x86, this avoids SFENCEs before doorbell writes in both the
tx and rx refill paths.
Signed-off-by: NVenkatesh Srinivas <venkateshs@google.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reverts two previous applied patches to fix an issue
that appeared when using SGMII based SFP modules. In the current
state the driver will try to reset the PHY before obtaining the
phy_addr of the SGMII attached PHY. That leads to an error in
e1000_write_phy_reg_sgmii_82575. Causing the initialization to
fail:

    igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
    igb: Copyright (c) 2007-2014 Intel Corporation.
    igb: probe of ????:??:??.? failed with error -3

The patches being reverted are:

    commit 18278533
    Author: Aaron Sierra <asierra@xes-inc.com>
    Date:   Tue Nov 29 10:03:56 2016 -0600

        igb: reset the PHY before reading the PHY ID

    commit 440aeca4
    Author: Matwey V Kornilov <matwey@sai.msu.ru>
    Date:   Thu Nov 24 13:32:48 2016 +0300

         igb: Explicitly select page 0 at initialization

The first reverted patch directly causes the problem mentioned above.
In case of SGMII the phy_addr is not known at this point and will
only be obtained by 'igb_get_phy_id_82575' further down in the code.
The second removed patch selects forces selection of page 0 in the
PHY. Something that the reset tries to address as well.

As pointed out by Alexander Duzck, the patch below fixes the same
issue but in the proper location:

    commit 4e684f59
    Author: Chris J Arges <christopherarges@gmail.com>
    Date:   Wed Nov 2 09:13:42 2016 -0500

        igb: Workaround for igb i210 firmware issue

Reverts: 440aeca4.
Reverts: 18278533.
Signed-off-by: NChristian Grönke <c.groenke@infodas.de>
Reviewed-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the ixgbe's security configuration registers into
the register dump.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

XDP does not support jumbo frames or LRO.  These checks are being made
outside the driver when an XDP program is loaded, however, there is
nothing preventing these from changing after an XDP program is loaded.
Add the checks so that while an XDP program is loaded, do not allow MTU
to be changed or LRO to be enabled.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, code at label *out* is unreachable. Fix this by updating
variable *ret* with -EINVAL, so the jump to *out* can be properly
executed instead of directly returning from function.

Addresses-Coverity-ID: 1472059 ("Structurally dead code")
Fixes: 1e2b44e7 ("rds: Enable RDS IPv6 support")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Build error, implicit declaration of function __inet6_ehashfn shows up
When RDS is enabled but not IPV6.
net/rds/connection.c: In function ‘rds_conn_bucket’:
net/rds/connection.c:67:9: error: implicit declaration of function ‘__inet6_ehashfn’; did you mean ‘__inet_ehashfn’? [-Werror=implicit-function-declaration]
  hash = __inet6_ehashfn(lhash, 0, fhash, 0, rds_hash_secret);
         ^~~~~~~~~~~~~~~
         __inet_ehashfn

Current code adds IPV6 as a depends on in config RDS.

Fixes: eee2fa6a ("rds: Changing IP address internal representation to struct in6_addr")
Signed-off-by: NAnders Roxell <anders.roxell@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: patches 2018-07-25

here are 4 more patches for SMC: The first one is just a small
code cleanup in preparation for patch 2. Patch 2 switches to the
use of the vlan-gid for VLAN traffic. Patch 3 improves diagnosis
when creating SMC connections. Patch 4 improves synchronization
between local and remote link groups.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Send an orderly DELETE LINK request before termination of a link group,
add support for client triggered DELETE LINK processing. And send a
disorderly DELETE LINK before module is unloaded.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remember the fallback reason code and the peer diagnosis code for
smc sockets, and provide them in smc_diag.c to the netlink interface.
And add more detailed reason codes.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMC code uses the base gid for VLAN traffic. The gids exchanged in
the CLC handshake and the gid index used for the QP have to switch
from the base gid to the appropriate vlan gid.

When searching for a matching IB device port for a certain vlan
device, it does not make sense to return an IB device port, which
is not enabled for the used vlan_id. Add another check whether a
vlan gid exists for a certain IB device port.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Link confirmation will always be sent across the new link being
confirmed. This allows to shrink the parameter list.
No functional change.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: protect from theoretical size overflows and SR-IOV errors

This small set changes the handling of pci_sriov_set_totalvfs() errors.
nfp is the only driver which fails probe on pci_sriov_set_totalvfs()
errors.  It turns out some BIOS configurations may break SR-IOV and
users who don't use that feature should not suffer.

Remaining patches makes sure we use overflow-safe function for ring
allocation, even though ring sizes are limited.  It won't hurt and
we can also enable fallback to vmalloc() if memory is tight while
at it.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use array_size() and store the size as full size_t to protect from
theoretical size overflow when handling HW descriptor rings.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 7f1c684a ("nfp: setup xdp_rxq_info") mixed the cache
cold and cache hot data in the nfp_net_rx_ring structure (ignoring
the feedback), to try to fit the structure into 2 cache lines
after struct xdp_rxq_info was added.  Now that we are about to add
a new field the structure will grow back to 3 cache lines, so
order the members correctly.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use kvcalloc() instead of tmp variable + kzalloc() when allocating
SW buffer information to allow falling back to vmalloc and to protect
from theoretical integer overflow.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On machines with buggy ACPI tables or when SR-IOV is already enabled
we may not be able to set the SR-IOV VF limit in sysfs, it's not fatal
because the limit is imposed by the driver anyway.  Only the sysfs
'sriov_totalvfs' attribute will be too high.  Print an error to inform
user about the failure but allow probe to continue.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma_mapping_error() returns true or false, but we want
to return -ENOMEM if there was an error.

Fixes: 174fd259 ("amd-xgbe: Implement split header receive support")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Introduce algorithmic TCAM support

The Spectrum-2 ASIC uses an algorithmic TCAM (A-TCAM) where multiple
exact matches lookups are performed instead of a single lookup as with
standard circuit TCAM (C-TCAM) memory. This allows for higher scale and
reduced power consumption.

The lookups are performed by masking a packet using different masks
(e.g., {dst_ip/24, ethtype}) defined for the region and looking for an
exact match. Eventually, the rule with the highest priority will be
picked.

Since the number of masks per-region is limited, the ASIC includes a
C-TCAM that can be used as a spill area for rules that do not fit into
the A-TCAM.

The driver currently uses a C-TCAM only mode which is similar to
Spectrum-1. However, this mode severely limits both the number of
supported ACL rules and the performance of the ACL lookup.

This patch set introduces initial support for the A-TCAM mode where the
C-TCAM is only used for rule spillage.

The first five patches add the registers and ASIC resources needed in
order to make use of the A-TCAM.

Next three patches are the "meat" and add the eRP core which is used to
manage the masks used by each ACL region. The individual commit messages
are lengthy and aim to thoroughly explain the subject.

The next seven patches perform small adjustments in the code and the
related data structures and are meant to prepare the code base to the
introduction of the A-TCAM in the last two patches.

Various A-TCAM optimization will be the focus of follow-up patch sets:

* Pruning - Used to reduce the number of lookups. Each rule will include
  a prune vector that indicates which masks should not be considered for
  further lookups as they cannot result in a higher priority match

* Bloom filter - Used to reduce the number of lookups. Before performing
  a lookup with a given mask the ASIC will consult a bloom filter
  (managed by the driver) that indicates whether a match might exist using
  the considered mask

* Masks aggregation - Used to increase scale and reduce lookups. Masks
  that only differ by up to eight consecutive bits (delta bits) can be
  aggregated into a single mask. The delta bits then become a part of the
  rule's key. For example, dst_ip/16 and dst_ip/17 can be represented as
  dst_ip/16 with a delta bit of one. Rules using the aggregated mask then
  specify whether the 17-th bit should be masked or not and its value
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that all the pieces are in place we can start using the A-TCAM
instead of only using the C-TCAM. This allows for much higher scale and
better performance (to be improved further by follow-up patch sets).

Perform the integration with the A-TCAM and the eRP core by reverting
the changes introduced by "mlxsw: spectrum_acl: Enable C-TCAM only mode
in eRP core" and add calls from the C-TCAM code into the eRP core.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement rule insertion and deletion into the A-TCAM before we flip the
driver to start using the A-TCAM.

Rule insertion into the A-TCAM is very similar to C-TCAM, but there are
subtle differences between regions of different sizes (i.e., different
number of key blocks).

Specifically, as explained in "mlxsw: spectrum_acl: Allow encoding a
partial key", in 12 key blocks regions a rule is split into two and the
two halves of the rule are linked using a "large entry key ID".

Such differences are abstracted away by using different region
operations per region type.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>