IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:

s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Xose Vazquez Perez points out that this file should not be marked
executable.
Reported-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.

New timings are based on application note
"NAND Flash Support on AT91SAM9 Microcontrollers" available at
http://atmel.com/dyn/resources/prod_documents/doc6255.pdf).
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Adds support for the USB High Speed Device Port on the AT91SAM9RL
system on chip. The AT91SAM9RL uses the same UDPHS IP as the AVR32 and
the AT91CAP9 (atmel_usba_udc driver).
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is patch 2 of 2 adding support for the USB High Speed Device Port
on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP
as the AVR32 and the AT91SAM9RL.

This patch declares the UDPHS ressources in the at91cap9 (cpu and
adk board) files, wires up the atmel_usba_udc driver to them,
and activates the driver in the defconfig.
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is patch 1 of 2 adding support for the USB High Speed Device Port
on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP
as the AVR32 and the AT91SAM9RL.

This patch makes the generic AT91 adaptations, mainly dealing with
the addition of the UDPHS UTMI clock.
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert the following AT91RM9200-based boards to the new-style UART
initialization:
  - Conitec ARM&EVA
  - Atmel AT91RM9200-DK
  - Embest ATEB9200
  - Atmel AT91RM9200-EK
  - KwikByte KB920x
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for three AT91-based boards available from Calao Systems:
USB_A9260, USB_A9263 and QIL_A9260.
Signed-off-by: NGrégory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Cleanup the YL9200 board-support file.

Other things fixed are:
 - Use new-style UART initialization
 - Register all LEDs as gpio_leds.
 - NOR Flash error noted in comments fixed by increasing YL9200_FLASH_SIZE
 - The only I2C device is the AT24C eeprom.
 - Setup of NWAIT pin and programming of SMC controller for the LCD/VGA.
 - Configure touchscreen interrupt pin.

Also adding the board to the KConfig and Makefile.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Export the AT91 clock functions for the AT91X40. Some external code common
to all AT91 family parts relys on this, like the gpio and serial support.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix initialization of framebuffer not calling ioremap_writecombine() function
and not using internal SRAM for at91sam9rl.

This is a little rework of the "Don't initialize a pre-allocated framebuffer"
patch that corrects the call to ioremap_writecombine() function.

It also cuts the use of internal SRAM for at91sam9rl : it is a bit small
for a framebuffer.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Based on earlier work by Jon Smirl and Jochen Friedrich.

Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>

Build fix for power management on at91sam9263:  it has two memory
controllers instead of just one, so it might have two banks of
DRAM to put into selfrefresh mode.  For now we continue to assume
only the first bank is populated.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

typo in mci configuration in devices files
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.

Therefore, we should only initialize the framebuffer if we allocated it
ourselves.  This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e.  the user didn't provide a fixed
address or the reservation failed.

I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

None of these files use any of the functionality promised by
asm/semaphore.h.  It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

Update AT91SAM9/CAP9 PIT driver to use generic time and clockevent
infrastructure:

 - Clocksource gives sub-microsecond timestamp precision, assuming
 memory is clocked at over 16 MHz.  It's less than a 32 bit counter,
 unless it's is also generating IRQs.

 - Clockevent device supports periodic mode only; no oneshot
 support from this hardware.  No IRQs generated unless it's the
 active clocksource.

Later, another timer (probably from a TC module) can provide a oneshot
clockevent device to get NO_HZ and High-Res-Timer behavior.

This also updates the timekeeping to use the actual master clock rate
on the system, instead of compile-time <asm/arch/timex.h> constants
matching what Atmel's EK boards use.  (Product boards may well differ!)

Plus cleanup:  rename "*_timer*" symbols to "*_pit*" (there are other
timers, but only one PIT); shorter lines; remove needless CPP stuff;
make several symbols static; etc.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

All the SAM9 boards supported by mainline and the AT91 patches have
been converted to the new-style UART initialization.  Therefore drop
support for the old at91_init_serial() interface for SAM9.

at91_uarts[] array can also be marked as __initdata.

The warning that no serial-console is defined moved from
at91_set_serial_console() to at91_add_device_serial() since the whole
point is the board-specific file is not calling
at91_set_serial_console().
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the emQbit ECB_AT91 board.
  <http://wiki.emqbit.com/free-ecb-at91>

Original patch from Nelson Castillo.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the Olimex SAM9-L9260 board.
 <http://www.olimex.com/dev/sam9-L9260.html>

Original patch from Ivan Vasilev.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the Kwikbyte KB9260 (CAM60) board.
 <http://www.kwikbyte.com/KB9260.html>

Original patch from Kwikbyte.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Converts the D1/PB2 LED to use the gpio-leds API and heartbeat trigger.
Signed-off-by: NBill Gatliff <bgat@billgatliff.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Converts the CSB637 to the new-style UART initialization API.
Signed-off-by: NBill Gatliff <bgat@billgatliff.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Converts the CSB337 target to the new UART initialization API.
Signed-off-by: NBill Gatliff <bgat@billgatliff.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the GPIO-driven LEDs (using NEW_LEDS) on the Atmel
SAM9260-EK and SAM9261-EK boards.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for AT73C213 audio DAC on the Atmel SAM9260-EK and
SAM9261-EK boards.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Register platform_devices for the Timer/Counter Block peripherals
found on the AT91RM9200, SAM9 & CAP9 processors.

Original patch from David Brownell.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The RTT-as-RTC driver will search for the user-specified RTT
peripheral via ID number (0 .. 1).
Therefore if the processor only contains a single RTT peripheral, we
need to set its platform_device.id to "0" instead of "-1".
Also add the missing platform_device resource for the CAP9 processor.

Bug reported by Sedji Gaouaou.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Reset controller on the SAM9/CAP9 processors will store the reason
for the last system reset.
On startup, display this information (wakeup signal, RTT alarm,
watchdog reset, user reset, etc)

Based on patch from David Brownell.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Basic power-management (suspend-to-ram) support for Atmel SAM9 and
CAP9 processors.

Based on comments & patches from Anti Sullin and David Brownell.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert the Atmel SAM9260-EK, SAM9261-EK, SAM9263-EK and SAM9RL-EK
boards to use the new-style UART initialization.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On AT91 processors that include an ECC controller, pass its base
address to the NAND driver via platform_device resources.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Enable system shutdown/power-off on AT91SAM9 and AT91CAP9 based boards.
This does not require power-management to be enabled, and the
pm_power_off method can be overridden in board-specific files if
necessary.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91CAP9 processor includes the same Static Memory Controller
(SMC) peripheral as the SAM9 processors, but replaces the SDRAM
Controller with a DDR/SDR Controller (DDRSDRC).

This patch splits the existing
include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and
at91sam9_smc.h.
It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. Configuration file for YL9200
2. Board file fro YL9200

Adds support for the UCdragon YL9200 board available widly in China
Signed-off-by: Nsteve birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Correct GPIO pin assignment for the LCD power control (PCI)
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.

(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix section warning:

 WARNING: arch/arm/mach-at91/built-in.o(.text+0xd74): Section mismatch in reference
        from the function init_programmable_clock()
        to the function .init.text:at91_css_to_clk()
 The function  init_programmable_clock() references
 the function __init at91_css_to_clk().
 This is often because init_programmable_clock lacks a __init
 annotation or the annotation of at91_css_to_clk is wrong.

In this case the only calls to and from init_programmable_clock()
are from code marked as "__init", so this fix is trivially correct.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NUwe Kleine-Knig <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>