Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 11 5月, 2010 2 次提交
    • D
      PM / Runtime: Add sysfs debug files · c92445fa
      由 Dominik Brodowski 提交于 
      Add a few sysfs files relating to runtime power management for
advanced debug purposes:

runtime_enabled: is runtime PM enabled for this device? States
	are "enabled", "disabled", "forbidden" or a combination
	of the latter two.

runtime_status:	what state is the device in currently? E.g., it
	reports "suspended" for runtime-suspended devices, and
        "active" for active devices. NOTE: if runtime_enabled
	returns "disabled", the value of this file may not
	reflect its physical state.

runtime_usage: the runtime PM usage count of a device

runtime_active_kids: the runtime PM children usage count of a device, or
	0 if the ignore_children flag is set.

Also, CONFIG_PM_SLEEP_ADVANCED_DEBUG is not defined in any Kconfig
file, so replace it with CONFIG_PM_ADVANCED_DEBUG.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      c92445fa
    • A
      PM: Allow runtime_suspend methods to call pm_schedule_suspend() · 240c7337
      由 Alan Stern 提交于 
      This patch (as1361) changes the runtime PM interface slightly; it
allows suspend requests to be scheduled while the runtime_suspend
method is running.  If the method succeeds then the scheduled request
is cancelled, whereas if the method fails then an idle notification is
sent only if no request was scheduled.

Being able to schedule suspend requests from within a runtime_suspend
method is useful for drivers that need to test for idleness and
suspend the device all while holding a single spinlock, or for drivers
that want to check for idleness by polling.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      240c7337
  3. 10 4月, 2010 1 次提交
  5. 07 4月, 2010 1 次提交
    • T
      nodemask: include slab.h from drivers/base/node.c · 18e5b539
      由 Tejun Heo 提交于 
      NODEMASK_ALLOC/FREE are mapped to kmalloc/free if NODES_SHIFT > 8.
Among its several users, drivers/base/node.c wasn't including slab.h
leading to build failure if NODES_SHIFT > 8.  Include slab.h from
drivers/base/node.c.

This isn't an ideal solution but including slab.h directly from
nodemask.h is not an option because nodemask.h gets included
everywhere.  For now, make it work by including slab.h from its users.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NIngo Molnar <mingo@elte.hu>
      18e5b539
  7. 30 3月, 2010 1 次提交
    • T
      include cleanup: Update gfp.h and slab.h includes to prepare for breaking... · 5a0e3ad6
      由 Tejun Heo 提交于 
      include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
      5a0e3ad6
  9. 28 3月, 2010 1 次提交
  11. 24 3月, 2010 1 次提交
  13. 19 3月, 2010 6 次提交
  15. 18 3月, 2010 1 次提交
    • H
      memory hotplug: allow setting of phys_device · bc32df00
      由 Heiko Carstens 提交于 
      /sys/devices/system/memory/memoryX/phys_device is supposed to contain the
number of the physical device that the corresponding piece of memory
belongs to.

In case a physical device should be replaced or taken offline for whatever
reason it is necessary to set all corresponding memory pieces offline.
The current implementation always sets phys_device to '0' and there is no
way or hook to change that.  Seems like there was a plan to implement that
but it wasn't finished for whatever reason.

So add a weak function which architectures can override to actually set
the phys_device from within add_memory_block().
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      bc32df00
  17. 08 3月, 2010 23 次提交
  19. 07 3月, 2010 1 次提交
    • R
      PM: Provide generic subsystem-level callbacks · d690b2cd
      由 Rafael J. Wysocki 提交于 
      There are subsystems whose power management callbacks only need to
invoke the callbacks provided by device drivers.  Still, their system
sleep PM callbacks should play well with the runtime PM callbacks,
so that devices suspended at run time can be left in that state for
a system sleep transition.

Provide a set of generic PM callbacks for such subsystems and
define convenience macros for populating dev_pm_ops structures.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      d690b2cd
  21. 27 2月, 2010 2 次提交
    • R
      PM: Allow device drivers to use dpm_wait() · f8824cee
      由 Rafael J. Wysocki 提交于 
      There are some dependencies between devices (in particular, between
EHCI USB controllers and their OHCI/UHCI siblings) which are not
reflected by the structure of the device tree.  With synchronous
suspend and resume these dependencies are taken into accout
automatically, because the devices in question are always registered
in the right order, but to meet these constraints with asynchronous
suspend and resume the drivers of these devices will need to use
dpm_wait() in their suspend/resume routines, so introduce a helper
function allowing them to do that.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      f8824cee
    • R
      PM: Start asynchronous resume threads upfront · 97df8c12
      由 Rafael J. Wysocki 提交于 
      It has been shown by testing that total device resume time can be
reduced significantly (by as much as 50% or more) if the async
threads executing some devices' resume routines are all started
before the main resume thread starts to handle the "synchronous"
devices.

This is a consequence of the fact that the slowest devices tend to be
located at the end of dpm_list, so their resume routines are started
very late.  Consequently, they have to wait for all the preceding
"synchronous" devices before their resume routines can be started
by the main resume thread, even if they are "asynchronous".  By
starting their async threads upfront we effectively move those
devices towards the beginning of dpm_list, without breaking their
ordering with respect to their parents and children.  As a result,
their resume routines are started much earlier and we are able to
save much more device resume time this way.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      97df8c12