Changes in the gain-control mechanism will require some changes in the header.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The present code fails to set the linked state when an interface is
added.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In rt2800_init_rfcsr_5592(), there's no need to write RF register 3 twice.
Signed-off-by: NKevin Lo <kevlo@kevlo.org>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When routine rtl_is_special_data() is called with false as its last argument,
and the returned value is not tested, the call is essentially an extended
no-op. Accordingly, these calls may be removed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-by: NMark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wcn36xx_err macro should not end in a semicolon as
there are 2 consecutive semicolons in the preprocessed
output.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NEugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable the beacon changed using BSS_CHANGED_BEACON. This is
especially useful for mesh mode.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under heavy load, the relatively small number of RX queue entries are
completely filled. With an increase from 16 to 32 entries, this condition
rarely happens.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.

@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@

-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: NMihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.

@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@

-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Arend van Spriel <arend@broadcom.com>
Reported-by: NMihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The cw1200_irq_handler() function expects the hwbus lock to be held when
it is called.  On the SDIO platform, this lock is implemented in terms
of sdio_claim_host/sdio_release_host.

This trivial patch makes it explicit that we are performing the hwbus
lock rather than something SDIO-specific.
Signed-off-by: NSolomon Peachy <pizza@shaftnet.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The reason that a scan failed for some reason (typically bad
parameters) should be logged even when debugging is turned off.
Signed-off-by: NSolomon Peachy <pizza@shaftnet.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can mess logs if user space try to open device again and again if
RFKILL switch is on. Do not print message and return ERFKILL error
instead to indicate where the problem is.

Note that iwl4965 handle this problem differently, it allows to open
device when radio is disabled.
Reported-by: NDietmar Rudolph <dietmar@crlf.de>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the original code used goto out if kzalloc fails,but the out include kfree,
so return -ENOMEM if kzalloc fails.
Signed-off-by: NJing Wang <windsdaemon@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since firmware loading became async it is possible that if_sdio_finish_power_of
is called with only one remaining runtime_pm reference, so it isn't safe
to call pm_runtime_put_noidle.  We must call pm_runtime_put().
Diagnosed-by: N"Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mirror the latest MediaTek/Ralink driver with respect to RT5390 RF register
programming.  The PCI and USB devices use different init values.
Signed-off-by: NKevin Lo <kevlo@kevlo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

1) Move common code out of switch case handling
2) Return from the function if number of bytes left in response buffer
are less than tlv size
3) Pass pg_tlv_hdr directly instead of txp_cfg to mwifiex_get_power_level()
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update bbp register initialization for RT53xx chips to match with the
latest MediaTek/Ralink driver.

Based on: NICInitRT5390BbpRegisters()
From: DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5390.c

Signed-off-by: Kevin Lo <kevlo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding the debugfs file <debugfs_mnt>/brcmfmac/<devid>/chipinfo
which contains the chip number and revision.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The dhd.h file contained a number of definitions that are
related to events received from the firmware. Those are
processed and dispatched in the driver by fweh. Hence the
definitions are moved to its include file.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removing WLC_PHY_TYPE and some BRCMF_E_.* definitions as these
are not used in the driver sources.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The BCDC protocol layer is using a mix of naming of CDC, BDC and
BCDC. Use the name BCDC consistenly over all functions, defines
and variables. This patch does not change code functionality.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the command codes to the firmware interface module as
that makes a bit more sense.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware control interface is provided by fwil source file, but
a number of structures used to communicate with the firmware still
resided in dhd.h. The patch moves them to fwil_types.h.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In bcmsdh.c the functions brcmf_sdio_probe() and brcmf_sdio_remove()
were exported, but that is not needed. The functions are linked into
the driver module, which is the only one needing to call these.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Knowing the firmware version is pretty useful information when
looking at issues. It is retrieved during initialization so
store it in driver data structure to fill the ethtool driver
info when requested.
Reviewed-by: NHante Meuleman <meuleman@brodcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BCDC is the default protocol layer and being called directly. This
patch installs the functions for this layer dynamically. This allows
new protocols to be added and selected dynamically depending on the
hw capabilties. As currently only BCDC is supported this is always
the installed protocol.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ioctl() entry points were empty except for handling SIOC_ETHTOOL
but that has been obsoleted in favor of struct ethtool_ops. Cleaning
up removing the ioctl() handlers.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The SDIO part of the brcmfmac driver uses a static define BRCMF_SDALIGN
to align buffers used for SDIO transfers. This patch replaces it by
using alignment derived from the platform specific data.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The alignment values were being determined for each transmit
and receive depending on platform data. Instead determine
these once during the probe.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dhd_proto.h was cleaned up and prototypes were moved to dhd.h.
dhd_proto.h was removed. This is a step in cleaning and
restucturing protocol layer.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dhd_cdc is renamed to bcdc. This is a step in cleaning and
restructuring protocol layer. This is done so new protocols can
be added in the future. This step only renames the source files.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
[arend@broadcom.com: use 'git mv' to do the rename]
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

New WiFi full dongle supports receiving chained packets in one command
through the SDIO bus. This patch adds the support on the host side to
send chained packets.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add firmware/nvram file name for bcm4339 so fmac can actually be functional with
the chip.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When CONFIG_BRCMDBG is not set we get the following build issue:
  CC [M]  drivers/net/wireless/brcm80211/brcmfmac/fwsignal.o
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:
    In function ‘brcmf_fws_hdrpush’:
	drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:852:18:
	error: ‘BRCMF_FWS_TYPE_SEQ_LEN’ undeclared

The define BRCMF_FWS_TYPE_SEQ_LEN was introduced by:

    commit 6918f38e4ed4e0493a90a4331e0033bdfc806e00
    Author: Hante Meuleman <meuleman@broadcom.com>
    Date:   Wed Oct 23 14:58:51 2013 +0200

        brcmfmac: Update fwsignal to fix out of order tx.

Unfortunately, it was put in conditional part of the source
file under #ifdef DEBUG.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "eb9c174 brcmfmac: determine host controller related
variables during probe" was not implemented correctly as the
information is already needed in brcmf_sdbrcm_probe(). This patch
moves it to brcmf_sdioh_attach() instead.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The SDPCM header can be traced, but it used a fixed header size. With
txglom feature the SDPCM header will have additional 8 bytes of hardware
extension header so SDIO core can properly handle the txglom packet.
Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>