This patch enables support for pause(0) power management state
for the Cell Broadband Processor, which is import for power efficient
operation. The pervasive infrastructure will in the future enable
us to introduce more functionality specific to the Cell's
pervasive unit.

From: Maximino Aguilar <maguilar@us.ibm.com>
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

At present, we are not looking at all interrupt controller nodes in the
device tree even though the proper node was not found. This is causing
the system panic. The attached patch will scan all nodes until it finds
the proper interrupt controller type.
Signed-off-by: NHaren Myneni <haren@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Added a common udbg_progress for use by ppc_md.progress()
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental !  There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There is code in the RPAPHP directory that is identical to this routine;
I'll be removing that code in an upcoming patch, but this patch is needed
to expose the function to make it callable.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We currently crash in the fedora installer because the keyboard
driver tries to access I/O space that is not there on our hardware.

This uses the same solution as powermac by just marking all
legacy i/o as invalid.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

So far, the iommu code was hardwired to a linear mapping
between 0x20000000 and 0x40000000, so it could only support
512MB of RAM.

This patch still keeps the linear mapping, but looks for
proper ibm,dma-window properties to set up larger windows,
this makes the maximum supported RAM size 2GB.

If there is anything unusual about the dma-window properties,
we fall back to the old behavior.

We also support switching off the iommu completely now
with the regular iommu=off command line option.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Because of always clearing DSISR at spu class 1 interrupt handler,
kernel may lose Class1[Mf] interrupt.
Signed-off-by: NMasato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: NGeoff Levand <geoff.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Output from hexdump with "%08x" depends on HOST platform's endian.
When building linux by cross toolchain, that difference makes errors.
Signed-off-by: NMasato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: NGeoff Levand <geoff.levand@am.sony.com>
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

One of my last patches contained a broken line
from splitting out some other changes, this
restores a working version.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

One of the two users of spufs_calls.owner still has a race
when calling try_module_get while the module is removed.
This makes it use the correct instance of owner.

Noticed by Milton Miller.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Handling mailbox interrupts was broken in multiple respects,
the combination of which was hiding the bugs most of the time.

- The ibox interrupt mask was open initially even though there
  are no waiters on a newly created SPU.

- Acknowledging the mailbox interrupt did not work because
  it is level triggered and the mailbox data is never retrieved
  from inside the interrupt handler.

- The interrupt handler delivered interrupts with a disabled
  mask if another interrupt is triggered for the same class
  but a different mask.

- The poll function did not enable the interrupt if it had not
  been enabled, so we might run into the poll timeout if none of
  the other bugs saved us and no signal was delivered.

We probably still have a similar problem with blocking
read/write on mailbox files, but that will result in extra
wakeup in the worst case, not in incorrect behaviour.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch reduces lock complexity of SPU scheduler, particularly
for involuntary preemptive switches.  As a result the new code
does a better job of mapping the highest priority tasks to SPUs.

Lock complexity is reduced by using the system default workqueue
to perform involuntary saves.  In this way we avoid nasty lock
ordering problems that the previous code had.  A "minimum timeslice"
for SPU contexts is also introduced.  The intent here is to avoid
thrashing.

While the new scheduler does a better job at prioritization it
still does nothing for fairness.

From: Mark Nutter <mnutter@us.ibm.com>
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch makes it easier to preempt an SPU context by
having the scheduler hold ctx->state_sema for much shorter
periods of time.

As part of this restructuring, the control logic for the "run"
operation is moved from arch/ppc64/kernel/spu_base.c to
fs/spufs/file.c.  Of course the base retains "bottom half"
handlers for class{0,1} irqs.  The new run loop will re-acquire
an SPU if preempted.

From: Mark Nutter <mnutter@us.ibm.com>
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

spufs is rather noisy when debugging is enabled, this
turns off the messages for production use.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

try_module_get returns true when NULL arguments, so
we first need to check if there is a module loaded before
getting the reference count.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

With the new rules for reserved pages, the spufs now
needs working page reference counting.

I should probably look into converting to vm_insert_page,
but for now this patch makes spufs work again.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This changes all exported symbols of spufs to EXPORT_SYMBOL_GPL.
The spu_ibox_read/spu_wbox_write symbols are not exported
any more when the scheduler patch is applied.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Implementing the machine_crash_shutdown which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Disable the
interrupts, shootdown cpus using debugger IPI and collect regs
for all CPUs.

elfcorehdr= specifies the location of elf core header stored by
the crashed kernel. This command line option will be passed by
the kexec-tools to capture kernel.

savemaxmem= specifies the actual memory size that the first kernel
has and this value will be used for dumping in the capture kernel.
This command line option will be passed by the kexec-tools to
capture kernel.
Signed-off-by: NHaren Myneni <haren@us.ibm.com>
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There's a few places where we need to fix things up for the kernel to work
if it's linked at 32MB:

 - platforms/powermac/smp.c
   To start secondary cpus on pmac we patch the reset vector, which is fine.
   Except if we're above 32MB we don't have enough bits for an absolute branch,
   it needs to relative.
 - kernel/head_64.s
    - A few branches in the cpu hold code need to load the full target address
      and do a bctr.
    - after_prom_start needs to load PHYSICAL_START as the dest address, not 0.
    - The exception prolog needs to load the low word of the target adddress,
      not just the low halfword.
    - Fixup handling of the initial stab address.
 - kernel/setup_64.c
   smp_release_cpus() needs to write 1 to the spinloop flag near 0, not 32 MB.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The fwnmi vectors can be anywhere < 32 MB, so we need to use a trampoline
for them. The kdump kernel will register the trampoline addresses, which will
then jump up to the real code above 32 MB.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Minor: use macro to perform void pointer deref; this may someday help
avoid pointer typecasting errors.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This updates the OF address parsers to return the IO flags
indicating the type of address obtained. It also adds a PCI
call for converting physical addresses that hit IO space into
into IO tokens, and add routines that return the translated
addresses into struct resource
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The udbg low level io layer has an issue with udbg_getc() returning a
char (unsigned on ppc) instead of an int, thus the -1 if you had no
available input device could end up turned into 0xff, filling your
display with bogus characters. This fixes it, along with adding a little
blob to xmon to do a delay before exiting when getting an EOF and fixing
the detection of ADB keyboards in udbg_adb.c
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When compiling without BOOTX_TEXT the following warning is emitted.
Fix up the definition to only be made when required.

      CC      arch/powerpc/platforms/powermac/udbg_adb.o
    .../arch/powerpc/platforms/powermac/udbg_adb.c:41: warning:
		`udbg_adb_use_btext' defined but not used
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

udbg_adb_init() has become dependent on btext_drawchar, even when
BOOTX_TEXT support is not selected.  This leads to the error below.
Make the check dependant on BOOTX_TEXT.

      LD      .tmp_vmlinux1
    arch/powerpc/platforms/built-in.o(.toc1+0xa40): undefined
					reference to `btext_drawchar'
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

23-rpaphp-migrate.patch (parts)

This patch moves some pci device add & remove code from the PCI
hotplug directory to the arch/powerpc/kernel directory, and cleans
it up a tad. The primary reason for this is that the code performs
some fairly generic operations that are shared with the PCI error
recovery code (living in the arch/powerpc/kernel directory).
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

20-rpaphp-eeh-cleanup.patch

This patch move some code from the rpaphp directory, to the powerpc
directory, where it should have been all along (Among other things, I
need it in the powerpc directory for the PCI error recovery.)

Please note that patch affects TWO maintainers: Paul, after applying
the powerpc part, please ask that GregKH appli the PCI part. It is safe
to have the powerpc part go in first. It would be bad to have the
PCI part go in first.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes the new serial probe code with some PCI MMIO UARTs, and fixes
CHRP build with ARCH=powerpc.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

My previous patches inadvertently broke building a G5 kernel with
CONFIG_XMON enabled. This fixes it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On iSeries, the paca contains, amongst other things an ItLpRegSave
structure used by the hypervisor to save registers.  The hypervisor
locates this area through a pointer at the beginning of the paca, so
the structure itself can be located elsewhere.  This patch moves the
reg_save area out into its own array.  This reduces the amount of
iSeries specific gunk which is visible to general powerpc code via
paca.h

Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Make get_IRQ return a pending irq number so it can be handled
in the powerpc geeneric code.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Hide some of the iseries details in iSeries_get_irq.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Encode the sub bus number into the real irq number (even though it
is always zero for now) so that we have enough information to do
the EOI in iseries_end_IRQ.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Remove two useless counters.
DeStropify.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

ARCH=powerpc couldn't boot from BootX as it uses a "different" way of
getting in the kernel. This patch adds the necessary trampolines,
creating a flattened device-tree from the tree passed from MacOS, and
initializing the btext engine early for really-early debugging.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.

For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.

Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.

It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds a scheduler for SPUs to make it possible to use
more logical SPUs than physical ones are present in the
system.

Currently, there is no support for preempting a running
SPU thread, they have to leave the SPU by either triggering
an event on the SPU that causes it to return to the
owning thread or by sending a signal to it.

This patch also adds operations that enable accessing an SPU
in either runnable or saved state. We use an RW semaphore
to protect the state of the SPU from changing underneath
us, while we are holding it readable. In order to change
the state, it is acquired writeable and a context save
or restore is executed before downgrading the semaphore
to read-only.

From: Mark Nutter <mnutter@us.ibm.com>,
      Uli Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>