[Why]
On some platforms, DMCU is no longer used. In these cases, some DMCU
memory should be completely powered off to save power.

[How]
1. Set DMCU_ERAM_MEM_PWR_FORCE to shutdown memory when DMCU is not in
   use
2. Added a debug option to allow this behaviour to be turned off
3. Set all memory low power debug options to off first, to not
   immediately cause problems
Signed-off-by: NJacky Liao <ziyu.liao@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We should use int for counting variable

[How]
Change type from bool to uint32_t
Signed-off-by: NRaymond Yang <rayyang@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The I2C memory blocks should be powered down when they are not in use.
This will reduce power consumption.

[How]
1. Write to I2C_LIGHT_SLEEP_FORCE to put memory in light sleep when
   released
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: NJacky Liao <ziyu.liao@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Check if the eDP sink supports the dynamic backlight control

[How]
Query the dynamic backlight capability in DPCD (eDP case only)
Signed-off-by: NRoy Chan <roy.chan@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Actual dpp/disp clock PMFW set are always equal or more than requested.
Need to cache the actual clock for debugging purpose.

[How]
Add actuall dpp/disp clk in clock manager and save it when set clocks.
Add an ASSERT in case of actual clock less than requested.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.

[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: NJing Zhou <Jing.Zhou@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Avoids confusion in configurations.

v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code

Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The OPTC memory blocks should be powered down when they are not in use.
This will reduce power consumption.

[How]
1. Set ODM_MEM_UNASSIGNED_PWR_MODE to shutdown memory when unassigned
2. Set ODM_MEM_VBLANK_PWR_MODE to light sleep mode when in vblank
3. Added a debug option to allow this behaviour to be turned off
4. Restructured debug options to use a bitfield in a way that's more clear
Signed-off-by: NJacky Liao <ziyu.liao@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The MPC memory blocks in DCN3 should be powered down completely when
they are not in use. This will reduce power consumption.

[How]
This commits changes behaviour for dcn3 and does the following:
1. Write to MPC_RMU<X>_LOW_PWR_MODE and MPCC_OGAM_MEM_LOW_PWR_MODE to
   automatically shut down memory when not in use
2. mpc3_power_on_shaper_3dlut and mpc3_power_on_ogam_lut are called
   to disable force power on when configuration finishes
3. Added a debug option to allow this behaviour to be turned off
Signed-off-by: NJacky Liao <ziyu.liao@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NGeorge Shen <george.shen@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.

[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: NAshley Thomas <Ashley.Thomas2@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Functions (disable_all_writeback_pipes_for_stream &
dc_enable_stereo & dc_post_update_surfaces_to_stream)
always return true, there is no need to keep the return value.
This change is to make the code a bit more readable.
Signed-off-by: NBernard Zhao <bernard@vivo.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.

[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.

This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: NCharlene Liu <Charlene.Liu@amd.com>
Reviewed-by: NChris Park <Chris.Park@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.

[How]
 - new hubbub func to control the force pstate register
 - force allow when releasing display ownership
   - registers are inaccessible after due to m_cgs.hwNotAvailable
 - explicitly disable force signal during hw_init
   - if driver is disabled and re-enabled, register not cleared otherwise

Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.
Signed-off-by: NJoshua Aberback <joshua.aberback@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
At the moment, some tests are failing because cur_link_settings is
invalid. As a workaround, add an option to force dio disable.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The ctx field of dc_transfer_func is not always populated and therefore
isn't reliable.

[How]
Remove dc context from dc_transfer_func
Signed-off-by: NJosip Pavic <Josip.Pavic@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[How]
 - use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
 - add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: NJoshua Aberback <joshua.aberback@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Disable triplebuffering by default.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
with eDP + DP, each display use one pipe. after DP unplugged, eDP switch
from one pipe to two pipes -- pipe split.  dpp1_cm_set_regamma_pwl will
be executed too. The duration from switch single pipe to dual pipes is a
little long which could let eDP enter PSR mode. upon two pipes for eDP
are setup, eDP PHY is disabled. front pipe is not really running to
fetch data from frame buffer. i.e., dchubp is not in normal working
status. execution of hubbub1_wm_change_req_wa may cause p-state warning.

[How]
disable eDP PSR before dc_commit_state. psr is disabled when execute
hubbub1_wm_change_req_wa.
Signed-off-by: NHersen Wu <hersenxs.wu@amd.com>
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Implement an interface to obtain plane size caps

[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: NIgor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies.  Powering down
hardware on boot will ensure SW state is accurate.

[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>