This copies the i8259 interrupt controller driver from arch/powerpc
to arch/ppc. It's currently shared by both architectures, but the upcoming
arch/powerpc interrupt changes will break the arch/ppc builds. The changes
are too important to just use #ifdef's in the driver.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is a resubmit with a proper subject and with all comments addressed.
Applies cleanly to powerpc.git 649e8579

Mark
--

The todc code from arch/ppc supports many todc/rtc chips and is needed
in arch/powerpc.  This patch adds the todc code to arch/powerpc.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
--

 arch/powerpc/Kconfig         |    7
 arch/powerpc/sysdev/Makefile |    1
 arch/powerpc/sysdev/todc.c   |  392 ++++++++++++++++++++++++++++++++++
 include/asm-powerpc/todc.h   |  487 +++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 887 insertions(+)
--
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add Tundra Semiconductor tsi108 pci and platform device data register
function support.
Signed-off-by: NAlexandre Bounine <alexandreb@tundra.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>

 ---
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Micro-optimisation - add no-minimal-toc to some more arch/powerpc Makefiles.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Parse the flat device tree for devices on Freescale SOC's that we know
about (gianfar, gianfar_mdio, i2c, mpc83xx_wdt).  We need to setup
platform devices and platform data for these devices to match arch/ppc
usage.

Also add a helper function (get_immrbase) that reports the base
address of the MMIO registers on the SOC.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Updated Kconfig & Makefiles in prep for adding support for the Freescale
MPC83xx family of processors to arch/powerpc.  Moved around some config
options that are more globally applicable to other PowerPC processors.
Added a temporary config option (83xx) to match existing arch/ppc support
for the MPC83xx line.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental !  There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The nvram code formally known as bpa_nvram.c is rather
generic really, so it is quite likely to be useful to
future boards not based on cell.

This patch puts it into arch/powerpc/sysdev.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NKumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is so that the 32-bit CHRP code can use it.  The MPC106
initialization code is now in arch/powerpc/sysdev/grackle.c and
is controlled by CONFIG_PPC_MPC106.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This changes the parameters for i8259_init so that it takes two
parameters: a physical address for generating an interrupt
acknowledge cycle, and an interrupt number offset.  i8259_init
now sets the irq_desc[] for its interrupts; all the callers
were doing this, and that code is gone now.  This also defines
a CONFIG_PPC_I8259 symbol to select i8259.o for inclusion, and
makes the platforms that need it select that symbol.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This defines a CONFIG_INDIRECT_PCI symbol to control whether it
gets used or not, and fixes the Kconfig to select that symbol for
platforms that need it.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This also puts a copy of indirect_pci.c in arch/powerpc/sysdev
so that we don't need to build in arch/ppc/syslib.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This creates the directory structure under arch/powerpc and a bunch
of Kconfig files.  It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac.  This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.

For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel.  This makes some minor changes
to files in those directories and files outside arch/powerpc.

The boot directory is still not merged.  That's going to be interesting.
Signed-off-by: NPaul Mackerras <paulus@samba.org>