Previously 8k30 worked with dsc and odm combine due to a workaround that ran
the formula a second time with dsc support enable should dsc validation fail.
This worked when clocks were low enough for formula to enable odm to lower
voltage, however now broke due to increased clocks.

This change updates the ODM combine policy within the formula to properly
reflect our current policy within DC, only enabling ODM when we have to, as
well as adding a check for viewport width when dsc is enabled.

As a side effect the redundant call to dml when odm is required is now
unnecessary.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Presently, there is no way for clocks to be lowered, only raised.

[HOW]
Compare clock status against previous known clock status, and optimize
if different.
This requires re-ordering the layout of the dc_clocks structure, as the
current ordering allows identical clock states to appear different.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Some ODM-related register settings are inconsistently updated by VBIOS, causing
the state in DC to be invalid, which would then end up crashing in certain
use-cases (such as disable/enable device).

[how]
Check the enabled status of the second pipe when determining the number of
OPTC sources. If the second pipe is disabled, set the number of sources to 1
regardless of other settings (that may not be updated correctly).
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
This change was made because DTO programming was double-buffered, which
is itself an issue. After deactivating the DTO double buffer, this
change becomes unnecessary.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
When changing DPP global ref clock, DTO adjustments must take effect
immediately, or else underflow may occur.
It appears the original decision to double-buffer DTO adjustments was made to
prevent underflows that occur when raising DPP ref clock (which is not
double-buffered), but that same decision causes similar issues when
lowering DPP global ref clock. The better solution is to order the
adjustments according to whether clocks are being raised or lowered.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Separating the hardware initialization from the creation of the
dc structures gives greater flexibility to the dm to override
options for debugging.

[How]
Move the hardware initialization call to a new function,
dc_hardware_init. No functional change is intended.
Signed-off-by: NJulian Parkin <julian.parkin@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Acked-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
I2C write command always send mot = true will cause sink state incorrect.

[How]
1. Remove default i2c write mot = true.
2. Deciding mot flag by is_end_of_payload flag.
Signed-off-by: NLewis Huang <Lewis.Huang@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The new implementation changed the behavior to allow process setMode
to DAL when DAL returns empty mode query for unplugged display.
This will trigger additional disable_link().
When unplug HDMI from MST dock, driver will update stream->signal to
"Virtual". disable_link() will call disable_output() if the signal type
is not DP and induce other displays on MST dock show black screen.

[How]
Don't need to process disable_output() if the signal type is virtual.
Signed-off-by: NMartin Tsai <martin.tsai@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

dcn20_calculate_dlg_params was incorrectly indexing pipe src and
dst structs when extracting global sync params.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NJaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Global sync update was missing vtg update resulting in underflow if
vstartup decreased a significant amount.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NJaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Surface dchub/dpp update would not trigger if a stream update was the
only cause. This change now allows stream flags to trigger this update.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
A function to adjust DPP clocks with DTO already exists; function code
is identical to the code replaced here
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
The issue is specific for linux, as on timings such as 8K@60
or 4K@144 DSC should be working in combination with ODM Combine
in order to ensure that we can run those timings. The validation
for those timings was passing, but when pipe split was happening
second pipe wasn't being programmed.

[how]
Rebuild mapped resources if we split stream for ODM.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Secondary viewport dimension/position registers are not programmed,
which can cause issues in some stereo configurations.

[How]
Add register definitions and register programming.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There is a spelling mistake in the variable name eanble,
rename it to enable.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
we only want the lowest voltage to be available for dali.

[How]
Use the get_highest_allowed_voltage_level function
to return 0 for dali
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DP1.2 LL CTS test failure.

[How]
The failure is caused by not verify stream link is equal
to link, only check stream and link is not null.
Signed-off-by: NJing Zhou <Jing.Zhou@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Description]
1. OUTSTANDING_REQUEST_LIMIT update from 0xFF to 0x1F (HW doc update)
2. using memory type to convert UMC's MCLK to Yclk.
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Edid Utility wishes to include DSC module from driver instead
of doing it's own logic which will need to be updated every time
someone modifies the driver logic.

[How]
Modify some functions such that we dont need to pass the entire
DC structure as parameter.
-Remove DC inclusion from module.
-Filter out problematic types and inclusions
Signed-off-by: NBayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why] Underflow occurs on some display setups(repro'd on 3x4K HDR) on boot,
mode set, and hot-plugs with. Underflow occurs because mem clk
is not set high after disabling pstate switching. This behaviour occurs
because some calculations assumed displays were synchronized.

[How] Add a condition to check if timing sync is disabled so that
synchronized vblank can be set to false.
Signed-off-by: NJaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: NAlvin Lee <Alvin.Lee2@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
dc_destroy should only clean up SW, this is because GPUs may be
removed before driver unload, leading to HW to be unavailable.

[how]
remove GPIO close as part of GPIO destroy, this is unnecessary because
GPIO is not shared, and GPIOs are generally closed after being opened

Add tracking to HW access during destructor to make future issues
easier to pinpoint, and block access to prevent hangs.
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
Use dcn2 blender, shaper, 3dlut registers
Signed-off-by: NVitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NVitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Remove code used to allow compilation error free
interface change.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

New behaviour will track global updates and update any hw that isn't
related to current stream being updated.

This should fix any issues caused by pipe split pipes being taken
by other streams.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
- Need to add missing surface address register definitions.
- RGBE+A does not work in a stereo configuration because
  surface addresses are no programmed correctly.

[How]
Added the register definitions and surface address programming.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
It's sometimes useful to have this option when debugging

[how]
Add a config flag. If the flag is not set, use driver default policy.
If the flag is set, use the value from the flag as the starting DSC slice
height.
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
The requirement has been clarified and only DSC 4:2:2 Native has to
be disabled.
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We should not allocate payloads if the link is lost until the link is retrained.
Some displays require this.
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why&How]
Driver defaults to 1-tap subsample mode for 4:2:2.
DCE11.2 added 3-tap. The policy is:
DCE8-DCE11 - change to 2-tap, it's better than 1-tap.
DCE11.2+ - use 3-tap

Note that 4:2:0 was added in DCE11.2 and already uses 3-tap always.
Note 2 is that DCE not covered on Linux, only DCN+
Signed-off-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When user mode use i2c over aux through ADL or DDI, the function
dal_ddc_service_query_ddc_data will be called. There are two issues.

1. When read/write length > 16byte, current always return false because
the DEFAULT_AUX_MAX_DATA_SIZE != length.
2. When usermode only need to read data through i2c, driver will write
mot = true at the same address and cause i2c sink confused. Therefore
the following read command will get garbage.

[How]
1. Add function dal_dcc_submit_aux_command to handle length > 16 byte.
2. Check read size and write size when query ddc data.
Signed-off-by: NLewis Huang <Lewis.Huang@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DML diags tests are failing because the struct contents get
clobbered by a memcpy.

[How]
Remove the memcpy call.
Signed-off-by: NIlya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The earlier patch "Hook up calls to do stereo mux and dig programming..."
doesn't include update for dcn21.

[How]
Align dcn21 gpio settings with updated stereo control interface.
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Acked-by: NAaron Liu <aaron.liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Hook up the DML changes for renoir.
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Need to check for renoir first.
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Enable the building of dcn21 support.
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add missing parameters, to make dcn21 compile
without errors
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

call update_bw_bounding_box in DC construct
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>