This patch stops the internal MAC Tx clock from being enabled as the
internal clock isn't used. The definition used for the bit controlling
this behaviour is renamed as well as it was wrongly named (bit 4 of
GMAC_CTRL_2_REG).

Fixes: 3919357f ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private port_list array has a list of pointers to mvpp2_port
instances. This list is allocated given the number of ports enabled in
the device tree, but the pointers are set using the port-id property. If
on a single port is enabled, the port_list array will be of size 1, but
when registering the port, if its id is not 0 the driver will crash.
Other crashes were encountered in various situations.

This fixes the issue by using an index not equal to the value of the
port-id property.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NYan Markman <ymarkman@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parsing fragmentation detection failed due to wrong configured
parser TCAM entry's. Some traffic was marked as fragmented in RX
descriptor, even it wasn't IP fragmented. The hardware also failed to
calculate checksums which lead to use software checksum and caused
performance degradation.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call skb_frag_dma_map multiple times if tx length is greater than
device max and avoid processing tx ring until entire packet has been
sent.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to a bug in aquantia atlantic card firmware, it sometimes reports
invalid link speed bits. That caused driver to report link down events,
although link itself is totally fine.

This patch ignores such out of blue readings.
Signed-off-by: NPavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver did a poor job in managing its Tx queues: Sometimes it could stop
tx queues due to link down condition in aq_nic_xmit - but never waked up
them. That led to Tx path total suspend.
This patch fixes this and improves generic queue management:
- introduces queue restart counter
- uses generic netif_ interface to disable and enable tx path
- refactors link up/down condition and introduces dmesg log event when
  link changes.
- introduces new constant for minimum descriptors count required for queue
  wakeup
Signed-off-by: NPavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although hardware is capable for almost 16K MTU, without max_mtu field
correctly set it only allows standard MTU to be used.
This patch enables max MTU, calculating it from hardware maximum frame size
of 16352 octets (including FCS).

Fixes: 5513e164 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Signed-off-by: NPavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inlining these functions creates lots of stack variables that each take
64 bytes when KASAN is enabled, leading to this warning about potential
stack overflow:

drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_cmd_flow_tbl_add':
drivers/net/ethernet/rocker/rocker_ofdpa.c:621:1: error: the frame size of 2752 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]

gcc-8 can now consolidate the stack slots itself, but on older versions
we get the same behavior by using a temporary variable that holds a
copy of the inline function argument.

Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mapping the RX DMA buffers, the driver was accidentally specifying
zero for the buffer length.  Under normal circumstances, SWIOTLB does not
need to allocate a bounce buffer, so the address is just mapped without
checking the size field.  This is why the error was not detected earlier.

Fixes: b9b17deb ("net: emac: emac gigabit ethernet controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Xiaolong reported a suspicious rcu_dereference_check in the device
unregister notifier callback. Since we do not dereference the
rx_handler_data, it's ok to just check for the value of the pointer.
Note that this section is already protected by rtnl_lock.

[  101.364846] WARNING: suspicious RCU usage
[  101.365654] 4.13.0-rc6-01701-gceed73a2 #1 Not tainted
[  101.370873] -----------------------------
[  101.372472] drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c:57 suspicious rcu_dereference_check() usage!
[  101.374427]
[  101.374427] other info that might help us debug this:
[  101.374427]
[  101.387491]
[  101.387491] rcu_scheduler_active = 2, debug_locks = 1
[  101.389368] 1 lock held by trinity-main/2809:
[  101.390736]  #0:  (rtnl_mutex){+.+.+.}, at: [<8146085b>] rtnl_lock+0xf/0x11
[  101.395482]
[  101.395482] stack backtrace:
[  101.396948] CPU: 0 PID: 2809 Comm: trinity-main Not tainted 4.13.0-rc6-01701-gceed73a2 #1
[  101.398857] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-20161025_171302-gandalf 04/01/2014
[  101.401079] Call Trace:
[  101.401656]  dump_stack+0xa1/0xeb
[  101.402871]  lockdep_rcu_suspicious+0xc7/0xd0
[  101.403665]  rmnet_is_real_dev_registered+0x40/0x4e
[  101.405199]  rmnet_config_notify_cb+0x2c/0x142
[  101.406344]  ? wireless_nlevent_flush+0x47/0x71
[  101.407385]  notifier_call_chain+0x2d/0x47
[  101.408645]  raw_notifier_call_chain+0xc/0xe
[  101.409882]  call_netdevice_notifiers_info+0x41/0x49
[  101.411402]  call_netdevice_notifiers+0xc/0xe
[  101.412713]  rollback_registered_many+0x268/0x36e
[  101.413702]  rollback_registered+0x39/0x56
[  101.414965]  unregister_netdevice_queue+0x79/0x88
[  101.415908]  unregister_netdev+0x16/0x1d

Fixes: ceed73a2 ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Reported-by: Nkernel test robot <xiaolong.ye@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the error handling paths 'goto error', except this one.
We should also go to error in this case, or some resources will be
leaking.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Found by coccinelle spatch "misc/of_table.cocci"
Signed-off-by: NThomas Meyer <thomas@m3y3r.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EMAC has the option of sending only a single pause frame when
flow control is enabled and the RX queue is full.  Although sending
only one pause frame has little value, this would allow admins to
enable automatic flow control without having to worry about the EMAC
flooding nearby switches with pause frames if the kernel hangs.

The option is enabled by using the single-pause-mode private flag.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current mapping between pri and tc is one to one,
so user can't map multi priorities to the same tc.
This patch changes the mapping to many to one.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rss_size is 1, 2, 4, 8, 16, 32, 64, 128, but acutal tc queue
size can be any u16 less than 128. If tc queue size is 5, we
set the rss_size to 8, indirection table will be used to limit
the size of actual queue size.
It may cause dropping of receiving packet in hardware if
rss_size is not set correctly.
For now, each TC has the same rss size.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a typo error for feild, which should be field.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hdev doesn't support DCB, rx private buffer is not allocated,
otherwise there is not enough buffer for rx shared buffer, causing
buffer allocation process to fail.
This patch fixes by checking the dcb capability in
hclge_rx_buffer_calc.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rx_priv_buf_alloc is used to tell hardware how much buffer is
used for rx direction, right now only the private buffer is
assigned.
For ae_dev that doesn't support DCB, private rx buffer is assigned
to zero, only shared rx buffer is used. So not setting the shared
rx buffer cause dropping of packet in SSU.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When rx private buffer is disabled, there may be some case that
the rx private buffer is not set to zero, which may cause buffer
allocation process to fail.
This patch fixes this problem by setting priv->enable to 0 and
priv->buf_size to zero when rx private buffer is disabled.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When ae_dev doesn't support DCB, DEFAULT_DV must be set to
a lower value, otherwise the buffer allocation process will
fail.
This patch fix it by setting it to 30K bytes.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When ae_dev doesn't support DCB, rx_priv_wl_config,
common_thrd_config and tm_qs_bp_cfg can't be called, otherwise
cmd return fail, which causes the hclge module initialization
process to fail.
This patch fix it by adding a DCB capability flag to check if
the ae_dev support DCB.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the ROCE supported flag in the driver_data
field of pci_device_id, delete roce_pci_tbl and change
HNAE_DEV_SUPPORT_ROCE_B to HNAE3_DEV_SUPPORT_ROCE_B.
This cleanup is done in order to support adding capability
in pci_device_id and to fix initialization failure when
cmd is not supported.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_ptp_check_pps_event will return 1 if FEC_T_TF_MASK caused
an interrupt. Don't return IRQ_NONE in this case.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FEC_ENET_TS_TIMER is not checked in the interrupt routine
so there is no need to enable it.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before queue 0 was always checked if any queue caused an interrupt.
It is better to just mark queue 0 if queue 0 has caused an interrupt.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Acked-by: NFugang Duan <Fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is pretty much a carbon copy of
commit 3079c652 ("caif: Fix napi poll list corruption")
with "caif" replaced by "emac".

The commit d75b1ade ("net: less interrupt masking in NAPI")
breaks emac.

It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty.  However, like some
other drivers emac tries to do a last-ditch check and if there is
more work it will call napi_reschedule and then immediately process
some of this new work.  Should the entire budget be consumed while
processing such new work then we will violate the new caller
contract.

This patch fixes this by not touching any work when we reschedule
in emac.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When register/unregister ae_dev, ae_dev should match all client
in the client_list. Enet and roce can co-exists together so we
should continue checking for enet and roce presence together.
So break should not be there.

Above caused problems in loading and unloading of modules.

Fixes: 38eddd126772 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is no vlan id in the packets, hardware will treat the vlan id
as 0 and look for the mac_vlan table. This patch set the default vlan id
of PF as 0. Without this config, it will fail when look for mac_vlan
table, and hardware will drop packets.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NMingguang Qu <qumingguang@huawei.com>
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the ethernet address copy instance with more
appropriate ether_addr_copy() function.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the initialization of MAC address, fetched from HNS3
firmware i.e. when it is not randomly generated, to the HNS3 hardware.

Fixes: ca60906d2795 ("net: hns3: Add support of HNS3 Ethernet Driver for
hip08 SoC")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the vector-to-ring map and unmap command and adds
INT_GL(for, Gap Limiting Interrupts) and VF id to it as required
by the hardware interface.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NMingguang Qu <qumingguang@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the IMP command being used to unmap the vector
from the corresponding ring.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Default phy address of every port is 0. Therefore, phy address for
each port need to be fetched from firmware and device initialized
with fetched non-default phy address.

Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several problems with commit 10377ba7 ("net: systemport:
Support 64bit statistics", first one got fixed in 7095c973 ("net:
systemport: Fix 64-bit stats deadlock").

The second problem is that this specific code updates the
stats64.tx_{packets,bytes} from ndo_get_stats64() and that is what we
are returning to ethtool -S. If we are not running a tool that involves
calling ndo_get_stats64(), then we won't get updated ethtool stats.

The solution to this is to update the stats from both call sites,
factoring that into a specific function, While at it, don't just check
the sizeof() but also the type of the statistics in order to use the
64-bit stats seqlock.

Fixes: 10377ba7 ("net: systemport: Support 64bit statistics")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems we have to be more careful in napi_complete_done()
use. This patch is not a revert, as it seems we can
avoid bug that Ville reported by moving the napi_complete_done()
test in the spinlock section.

Many thanks to Ville for detective work and all tests.

Fixes: 617f0121 ("8139too: use napi_complete_done()")
Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for ingress-only qdisc for flower offload, as other qdiscs
are not supported for flower offload.
Suggested-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.

This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.

Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAndreas Rammhold <andreas@rammhold.de>
Reported-by: NFlorian Klink <flokli@flokli.de>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the network interface is kept running during suspend, the net core
may call net_device_ops.ndo_start_xmit() while the Ethernet device is
still suspended, which may lead to a system crash.

E.g. on sh73a0/kzm9g and r8a73a4/ape6evm, the external Ethernet chip is
driven by a PM controlled clock.  If the Ethernet registers are accessed
while the clock is not running, the system will crash with an imprecise
external abort.

As this is a race condition with a small time window, it is not so easy
to trigger at will.  Using pm_test may increase your chances:

    # echo 0 > /sys/module/printk/parameters/console_suspend
    # echo platform > /sys/power/pm_test
    # echo mem > /sys/power/state

To fix this, make sure the network interface is quietened during
suspend.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can enter a deadlock situation because there is no sufficient protection
when ndo_get_stats64() runs in process context to guard against RX or TX NAPI
contexts running in softirq, this can lead to the following lockdep splat and
actual deadlock was experienced as well with an iperf session in the background
and a while loop doing ifconfig + ethtool.

[    5.780350] ================================
[    5.784679] WARNING: inconsistent lock state
[    5.789011] 4.13.0-rc7-02179-g32fae27c725d #70 Not tainted
[    5.794561] --------------------------------
[    5.798890] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[    5.804971] swapper/0/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
[    5.810175]  (&syncp->seq#2){+.?...}, at: [<c0768a28>] bcm_sysport_tx_reclaim+0x30/0x54
[    5.818327] {SOFTIRQ-ON-W} state was registered at:
[    5.823278]   bcm_sysport_get_stats64+0x17c/0x258
[    5.828053]   dev_get_stats+0x38/0xac
[    5.831776]   rtnl_fill_stats+0x30/0x118
[    5.835761]   rtnl_fill_ifinfo+0x538/0xe24
[    5.839921]   rtmsg_ifinfo_build_skb+0x6c/0xd8
[    5.844430]   rtmsg_ifinfo_event.part.5+0x14/0x44
[    5.849201]   rtmsg_ifinfo+0x20/0x28
[    5.852837]   register_netdevice+0x628/0x6b8
[    5.857171]   register_netdev+0x14/0x24
[    5.861051]   bcm_sysport_probe+0x30c/0x438
[    5.865280]   platform_drv_probe+0x50/0xb0
[    5.869418]   driver_probe_device+0x2e8/0x450
[    5.873817]   __driver_attach+0x104/0x120
[    5.877871]   bus_for_each_dev+0x7c/0xc0
[    5.881834]   bus_add_driver+0x1b0/0x270
[    5.885797]   driver_register+0x78/0xf4
[    5.889675]   do_one_initcall+0x54/0x190
[    5.893646]   kernel_init_freeable+0x144/0x1d0
[    5.898135]   kernel_init+0x8/0x110
[    5.901665]   ret_from_fork+0x14/0x2c
[    5.905363] irq event stamp: 24263
[    5.908804] hardirqs last  enabled at (24262): [<c08eecf0>] net_rx_action+0xc4/0x4e4
[    5.916624] hardirqs last disabled at (24263): [<c0a7da00>] _raw_spin_lock_irqsave+0x1c/0x98
[    5.925143] softirqs last  enabled at (24258): [<c022a7fc>] irq_enter+0x84/0x98
[    5.932524] softirqs last disabled at (24259): [<c022a918>] irq_exit+0x108/0x16c
[    5.939985]
[    5.939985] other info that might help us debug this:
[    5.946576]  Possible unsafe locking scenario:
[    5.946576]
[    5.952556]        CPU0
[    5.955031]        ----
[    5.957506]   lock(&syncp->seq#2);
[    5.960955]   <Interrupt>
[    5.963604]     lock(&syncp->seq#2);
[    5.967227]
[    5.967227]  *** DEADLOCK ***
[    5.967227]
[    5.973222] 1 lock held by swapper/0/0:
[    5.977092]  #0:  (&(&ring->lock)->rlock){..-...}, at: [<c0768a18>] bcm_sysport_tx_reclaim+0x20/0x54

So just remove the u64_stats_update_begin()/end() pair in ndo_get_stats64()
since it does not appear to be useful for anything. No inconsistency was
observed with either ifconfig or ethtool, global TX counts equal the sum of
per-queue TX counts on a 32-bit architecture.

Fixes: 10377ba7 ("net: systemport: Support 64bit statistics")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.

Semantic patch used to resolve this issue:

@@
expression e,e2; constant c;
statement S;
@@

  e = kzalloc(e2, c);
  if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: NHimanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: NHimanshu Jha <himanshujha199640@gmail.com>
Acked-by: NSudarsana Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>