SDCC controller reset (SW_RST) during probe may trigger power irq if
previous status of PWRCTL was either BUS_ON or IO_HIGH_V. So before we
enable the power irq interrupt in GIC (by registering the interrupt
handler), we need to ensure that any pending power irq interrupt status
is acknowledged otherwise power irq interrupt handler would be fired
prematurely.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NVijay Viswanath <vviswana@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The delay circuit used to support HS400 is calibrated based on two
additional clocks. When these clocks are not available and
FF_CLK_SW_RST_DIS is not set in CORE_HC_MODE, reset might fail. But on
some platforms this doesn't work properly and below dump can be seen in
the kernel log.

  mmc0: Reset 0x1 never completed.
  mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
  mmc0: sdhci: Sys addr:  0x00000000 | Version:  0x00001102
  mmc0: sdhci: Blk size:  0x00004000 | Blk cnt:  0x00000000
  mmc0: sdhci: Argument:  0x00000000 | Trn mode: 0x00000000
  mmc0: sdhci: Present:   0x01f80000 | Host ctl: 0x00000000
  mmc0: sdhci: Power:     0x00000000 | Blk gap:  0x00000000
  mmc0: sdhci: Wake-up:   0x00000000 | Clock:    0x00000002
  mmc0: sdhci: Timeout:   0x00000000 | Int stat: 0x00000000
  mmc0: sdhci: Int enab:  0x00000000 | Sig enab: 0x00000000
  mmc0: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000000
  mmc0: sdhci: Caps:      0x742dc8b2 | Caps_1:   0x00008007
  mmc0: sdhci: Cmd:       0x00000000 | Max curr: 0x00000000
  mmc0: sdhci: Resp[0]:   0x00000000 | Resp[1]:  0x00000000
  mmc0: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
  mmc0: sdhci: Host ctl2: 0x00000000
  mmc0: sdhci: ============================================

Add support for the additional calibration clocks to allow these
platforms to be configured appropriately.

Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

By stuffing the runtime controlled clocks into a clk_bulk_data array we
can utilize the newly introduced bulk clock operations and clean up the
error paths. This allow us to handle additional clocks in subsequent
patch, without the added complexity.

Cc: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Programming legacy HOST SDMA Buffer Boundary bits in Block Size Register
(0x04) is not supported in Qualcomm sdhci controllers. Writing to this
would cause the controller not to transfer last block in case block size
is 4 bytes or less.

This issue was noticed while testing sdio wlan card on Qcom DB410c board.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Detected by sparse.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The spin lock is not necessary in set_ios. Anything that is racing with
changes to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host. So remove spin_lock and friends
from sdhci_set_ios and related callbacks.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLudovic Desroches <ludovic.desroches@microchip.com>

This removes CDC init sequence comments which are
not useful anyway.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

platform_execute_tuning should not really exist as it does not
do anything useful.

So remove this ops and directly plug sdhci_msm_execute_tuning
with mmc_host_ops.

Also in case of HS400 tuning clear SDHCI_HS400_TUNING flag once
HS400 related mode selection is done.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This provides enhanced_strobe mode feature support in sdhci-msm
driver.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

During tuning execution for HS400 mode, HW sequence recommends
to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC
to be 400MHZ (nearest supported clk). Add this change in tuning
sequence during HS400 tuning.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay.
We may see data CRC errors if it's programmed for any other delay
value.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Factor out sdhci_msm_hs400 used for DLL calibration in HS400
modes. This function will be needed for enhanced_strobe as well.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Factor out msm_set/get_clock_rate_for_bus_mode for it's later
use in changing the tuning sequence for selecting HS400
bus speed mode.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This factors out sdhci_msm_hc_select_mode to later use
it during enhanced_strobe mode select.
It also further breaks sdhci_msm_hc_select_mode
into separate functions for configuring HS400 mode
or other modes.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Tested-by: NJeremy McNicoll <jeremymc@redhat.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.

The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.

The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NKrishna Konda <kkonda@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.

The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sdhc-msm controller needs this SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN
& SDHCI_QUIRK2_PRESET_VALUE_BROKEN to be set. Hence setting it.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.
Signed-off-by: NSahitya Tummala <stummala@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.

Without this patch we see below errors on such SDHC controllers
	sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
	mmc0: tuning execution failed: -110
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Provides runtime PM callbacks to enable and disable clock resources
when idle. Also support system PM callbacks to be called during system
suspend and resume.
Reviewed-by: NRitesh Harjani <riteshh@codeaurora.org>
Reviewed-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Tested-by: NRitesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NPramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix to return a negative error code from the platform_get_irq_byname()
error handling case instead of 0, as done elsewhere in this function.

Fixes: ad81d387 ("mmc: sdhci-msm: Add support for UHS cards")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enabling support for ultra high speed mode cards requires some
voltage switching and interaction with the PMIC via a special
power IRQ. Add support for this.
Signed-off-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To allow UHS mode to work properly, we need to implement a Qualcomm
specific set_uhs_signaling() callback function. This function differs
from the sdhci_set_uhs_signaling() in that we need check the clock
rate and enable UHS timing only if the frequency is above 100MHz.

This patch resolves the mmc_select_hs200 timeouts noticed after merging
commit a5c1f3e55c99 ("mmc: mmc: do not use CMD13 to get status after
speed mode switch")

mmc0: mmc_select_hs200 failed, error -110
mmc0: error -110 whilst initialising MMC card
mmc0: Reset 0x1 never completed.
sdhci: =========== REGISTER DUMP (mmc0)===========
sdhci: Sys addr: 0x00000000 | Version: 0x00002e02
sdhci: Blk size: 0x00004000 | Blk cnt: 0x00000000
sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci: Present: 0x01f80000 | Host ctl: 0x00000000
sdhci: Power: 0x00000000 | Blk gap: 0x00000000
sdhci: Wake-up: 0x00000000 | Clock: 0x00000003
sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci: Caps: 0x322dc8b2 | Caps_1: 0x00008007
sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
sdhci: Host ctl2: 0x00000000
sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x0000000000000000
sdhci: ===========================================

Fixes: a5c1f3e55c99 ("mmc: mmc: do not use CMD13 to get status after...")
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The controller does not clear the "reset bit" when it is reset without
a card in the slot. Because of this, the following error message is seen
while booting with no plugged SD card.

mmc1: Reset 0x1 never completed.

Add the SDHCI_QUIRK_NO_CARD_NO_RESET quirk to avoid this.
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Tested-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

trivial fix to spelling mistake in dev_err message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit 0e748234 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-msm
to this allocation.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There's no need to allocate one sdhci_msm_pdata for each sdhci_msm_host.
This patch removes the sdhci_msm_pdata member from sdhci_msm_host and
uses one static global sdhci_msm_pdata for all sdhci msm hosts. It also
marks sdhci_msm_ops as const.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.

in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Ensure SDCC is working with maximum clock otherwise card
detection could be extremely slow, up to 7 seconds.
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some versions of this controller do not advertise their 3.0v and
8bit bus-width support capabilities. It is required to explicitly
set these capabilities for the specific controller versions.
Signed-off-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API instead.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Acked-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>

The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If we're tuning on a big-endian CPU we'll never determine we properly
tuned the device because we compare the data we received from the
controller with a table that assumes the CPU is little-endian.
Change the table to be an array of bytes instead of 32-bit words
so we can use memcmp() without needing to byte-swap every word
depending on the endianess of the CPU.

Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Reviewed-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Fixes: 415b5a75 "mmc: sdhci-msm: Add platform_execute_tuning implementation"
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>