For all the hist command request from testmode, set the CMD_ON_DEMAND flag.
this flag will be used later to control the uCode behavior
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Declare iwl_mac_rssi_callback as "static"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WiFi throughput drops drastically when BT is turned on, BT and WiFi
are simultaneously transmitting/receiving traffic. This is particularly true
when BT has higher priority over WiFi, and hence the device defers TX frames.
The AP assumes that the channel is bad and reduces the data rate, implying
longer airtime, which exacerbates the problem further, resulting ultimately
in what is popularly called the "death-spiral" phenomenon. The use of PS-poll
in such scenarios guarantees a low but consistent throughput.

Since the death-spiral phenomenon is observed only when the RSSI is low, use
PS-poll only when RSSI is low and disable when high, with a known hysterisis.

This feature specifies the high and low thresholds and implements the
callbacks registered with mac80211, which will be called when threshold events
occur.

iwlwifi: dynamic pspoll: optimize rssi monitor code
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For bt combo devices, need to use bt enabled handlers and functions
Reported-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No need to do double level indirect call after driver split
no functional changes
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not needed since the driver split.  Eliminate redundant routine.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not needed since the driver split.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not needed since the driver split.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the for priv->trans.ops->...
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not needed since the driver split.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now, there are only two functions to send a host command:
* send_cmd that receives a iwl_host_cmd
* send_cmd_pdu that builds the iwl_host_cmd itself and received flags

The flags CMD_ASYNC / CMD_SYNC / CMD_WANT_SKB are not changed by the API
functions.

Kill the unused flags CMD_SIZE_NORMAL / CMD_NO_SKB on the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Code duplication was needed during the move, not needed any more.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tx stop moves to transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rx stop moves to transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tx free functions move to the transport layer. Unify the functions that deal with tx queues and cmd queue.

Since the CMD queue is not fully allocated, but uses the q->n_bd / q->window trick, the release flow of TX queue and CMD queue was different.
iwlagn_txq_free_tfd receives now the index of the TFD to be freed, which allows to unify the release flow for all the queues.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is uneeded since Johannes removed the HUGE flag. The DMA mapping is always held in the same index as the command.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent firmware changes report tx ack status properly
to driver. Hence updating ath9k_htc driver capabilities.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes read only registers that cause invalid
address access and also updates index for measurement filter
calibration window size.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The power detector calibration is disabled because this block
doesn't exist in AR9003 based chips and also parallel
calibration is enabled otherwise the calibration will never stop.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The number of temperature reading samples to average
during a Tx packet is decreased to 1 from 2 to improve
5G Tx EVM with chain 0-only mode.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In XMIT path, the skb that we get from the kernel itself is not
aligned with 4-byte boundary on some embedded platforms.

Had it not been the presence of tx_pkt_offset field in txpd, 4 byte
memory alignment was not possible without memmove of entire skb.
And that would have increased MIPS instead of reducing.

With this patch few memory cycles can be saved while fetching
interface header and txpd structure because of 4 bytes memory
alignment.
Reported-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Tested-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Debugfs command 'info' shows wrong interface type. The regression
occurred due to commit eecd8250 (mwifiex: remove MWIFIEX_BSS_MODE_
macros) in which we replaced MWIFIEX_BSS_MODE_* macros by
NL80211_IFTYPE_*, for example,

MWIFIEX_BSS_MODE_IBSS (2) --> NL80211_IFTYPE_ADHOC (1)

The issue is fixed by swapping static character array used to
display interface type information.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Htcapinfo is unnecessarily sent in assoc request in WEP security due
to a regression introduced by commit 2be50b8d (mwifiex: remove
redundant encryption_mode mapping).
The issue is fixed in this patch.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>

sc->imask may change if ath5k_set_current_imask() races against itself.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>

The reg variable is only used by __raw_writel() and __raw_readl(), which
should guarantee memory access in the right order.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Without them we get Oops with NULL pointer
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>