Stop some other people peering into the baud bits on their own and make
them use the tty_get_baud_rate() helper as a preperation for the move to
the new termios.  Corrected dependancy previous one had on new termios
structs
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for logical volumes >2TB.  All SAS/SATA controllers support
large volumes.
Signed-off-by: NMike Miller <mike.miller@hp.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add infrastructure to track "maximum allowable latency" for power saving
policies.

The reason for adding this infrastructure is that power management in the
idle loop needs to make a tradeoff between latency and power savings
(deeper power save modes have a longer latency to running code again).  The
code that today makes this tradeoff just does a rather simple algorithm;
however this is not good enough: There are devices and use cases where a
lower latency is required than that the higher power saving states provide.
 An example would be audio playback, but another example is the ipw2100
wireless driver that right now has a very direct and ugly acpi hook to
disable some higher power states randomly when it gets certain types of
error.

The proposed solution is to have an interface where drivers can

* announce the maximum latency (in microseconds) that they can deal with
* modify this latency
* give up their constraint

and a function where the code that decides on power saving strategy can
query the current global desired maximum.

This patch has a user of each side: on the consumer side, ACPI is patched
to use this, on the producer side the ipw2100 driver is patched.

A generic maximum latency is also registered of 2 timer ticks (more and you
lose accurate time tracking after all).

While the existing users of the patch are x86 specific, the infrastructure
is not.  I'd like to ask the arch maintainers of other architectures if the
infrastructure is generic enough for their use (assuming the architecture
has such a tradeoff as concept at all), and the sound/multimedia driver
owners to look at the driver facing API to see if this is something they
can use.

[akpm@osdl.org: cleanups]
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NJesse Barnes <jesse.barnes@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch defines:
* a generic boolean-type, named 'bool'
* aliases to 0 and 1, named 'false' and 'true'

Removing colliding definitions of 'bool', 'false' and 'true'.
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Migate CONFIG_MEMORY_HOTPLUG to CONFIG_MEMORY_HOTPLUG_SPARSE where needed.
Signed-off-by: NKeith Mannthey <kmannth@us.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In cases where the acpi memory-add event does not containe the pxm (node)
infomation allow the driver to look up node info based on the address.  The
acpi_get_node call returns -1 if it can't decode the pxm info, this causes
add_memory to panic.  acpi_get_node would have to decode the resource from the
handle (a lenghty proposition).  This seems to be the cleanist point to
interject the hook.

[kamezawa.hiroyu@jp.fujitsu.com: build fixes]
[y-goto@jp.fujitsu.com: build fixes]
Signed-off-by: NKeith Mannthey <kmannth@us.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes two things

Firstly someone mistakenly used "errata" for the singular.  This causes
Dave Woodhouse to emit diagnostics whenever the string is read, and so
should be fixed.

Secondly the AMD AGP tunnel has an erratum which causes hangs if you try
and do direct PCI to AGP transfers in some cases.  We have a flag for
PCI/PCI failures but we need a different flag for this really as in this
case we don't want to stop PCI/PCI transfers using things like IOAT and the
new RAID offload work.

I'll post some updates to make proper use of the PCIAGP flag in the
media/video drivers to Mauro.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The ->flags in struct request was split into two variables, in a recent
changeset.  The merge of this change forgot to update SCSI's libsas,
probably because libsas was a very recent merge.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This makes CONFIG_USB_STORAGE depend on CONFIG_SCSI rather than selecting it,
as selecting it makes CONFIG_USB_STORAGE override the dependencies of SCSI,
causing it to turn on even if they aren't all met.
Signed-Off-By: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Make it possible to disable the block layer.  Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.

This patch does the following:

 (*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
     support.

 (*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
     an item that uses the block layer.  This includes:

     (*) Block I/O tracing.

     (*) Disk partition code.

     (*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.

     (*) The SCSI layer.  As far as I can tell, even SCSI chardevs use the
     	 block layer to do scheduling.  Some drivers that use SCSI facilities -
     	 such as USB storage - end up disabled indirectly from this.

     (*) Various block-based device drivers, such as IDE and the old CDROM
     	 drivers.

     (*) MTD blockdev handling and FTL.

     (*) JFFS - which uses set_bdev_super(), something it could avoid doing by
     	 taking a leaf out of JFFS2's book.

 (*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
     linux/elevator.h contingent on CONFIG_BLOCK being set.  sector_div() is,
     however, still used in places, and so is still available.

 (*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
     parts of linux/fs.h.

 (*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.

 (*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.

 (*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
     is not enabled.

 (*) fs/no-block.c is created to hold out-of-line stubs and things that are
     required when CONFIG_BLOCK is not set:

     (*) Default blockdev file operations (to give error ENODEV on opening).

 (*) Makes some /proc changes:

     (*) /proc/devices does not list any blockdevs.

     (*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.

 (*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.

 (*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
     given command other than Q_SYNC or if a special device is specified.

 (*) In init/do_mounts.c, no reference is made to the blockdev routines if
     CONFIG_BLOCK is not defined.  This does not prohibit NFS roots or JFFS2.

 (*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
     error ENOSYS by way of cond_syscall if so).

 (*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
     CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Move the loop device ioctl compat stuff from fs/compat_ioctl.c to the loop
driver so that the loop header file doesn't need to be included.
Signed-Off-By: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

It is a leftover from before the softirq completion was migrated
to the block layer.
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Signed-off-by: NJens Axboe <axboe@suse.de>

After Christophs SCSI change, the only usage left is RQ_ACTIVE
and RQ_INACTIVE. The block layer sets RQ_INACTIVE right before freeing
the request, so any check for RQ_INACTIVE in a driver is a bug and
indicates use-after-free.

So kill/clean the remaining users, straight forward.
Signed-off-by: NJens Axboe <axboe@suse.de>

As the comments indicates in blkdev.h, we can fold it into ->end_io_data
usage as that is really what ->waiting is. Fixup the users of
blk_end_sync_rq().
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: NJens Axboe <axboe@suse.de>

Delay the call to adapter->client_register() until after we are
certain that the client registration is a success. At this point the
client is fully initialized and we no longer hold the adapter->clist
mutex, so this should prevent the deadlocks if the client_register()
callback needs to take that mutex too, as is the case for the bttv
driver.

This fixes bug #7234.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

MSI is defined to be 32-bit write.  The 5706 does 64-bit MSI writes
with byte enables disabled on the unused 32-bit word.  This is legal
but causes problems on the AMD 8132 which will eventually stop
responding after a while.

Without this patch, the MSI test done by the driver during open will
pass, but MSI will eventually stop working after a few MSIs are
written by the device.

AMD believes this incompatibility is unique to the 5706, and
prefers to locally disable MSI rather than globally disabling it
using pci_msi_quirk.

Update version to 1.4.45.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix undefined reference in i2c_sibyte_exit().

   drivers/built-in.o: In function `i2c_sibyte_exit':
   i2c-sibyte.c:(.exit.text+0x368): undefined reference to `i2c_del_bus'
   i2c-sibyte.c:(.exit.text+0x368): relocation truncated to fit: R_MIPS_26 against `i2c_del_bus'
   i2c-sibyte.c:(.exit.text+0x38c): undefined reference to `i2c_del_bus'
   i2c-sibyte.c:(.exit.text+0x38c): relocation truncated to fit: R_MIPS_26 against `i2c_del_bus'
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If you send a priority character (as is done for flow control) then the tty
driver can either have its own method for "jumping the queue" or the characrer
can be queued normally.  In the latter case we call the write method but
without the atomic_write_lock taken elsewhere.

Make this consistent.  Note that the send_xchar method if implemented remains
outside of the lock as it can jump ahead of a current write so must not be
locked out by it.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

[PATCH] istallion: Remove private baud rate decoding, which is also broken in this case on some platforms
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The driver has no business doing this work itself any more and hasn't for some
years.  When the new speed stuff goes in this will break entirely so fix it up
ready.

Also remove a #if 0 around a comment....
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If the chip detected "oscillator stop" condition, show an warning message.
And initialize it with the Epoch time instead of leaving it with unknown
date/time.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

For len equal to 4, we never call sppp_lcp_conf_parse_options(),
therefore rmagic does not get initialized.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Acked-by: NPaul Fulghum <paulkf@microgate.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch limits the messages when ldisc open faulures happen.  It happens
under memory pressure.
Signed-off-by: NAkinobu Mita <mita@miraclelinux.com>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change corrects the logic on the preprocessor conditionals that
include support for ISA port i/o (/dev/ioports) into the mem character
driver.

This fixes the following error when building for powerpc platforms with
CONFIG_PCI=n.

  drivers/built-in.o: undefined reference to `pci_io_base'
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NLinas Vepstas <lins@austin.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Forward port of the patch by Solar and ported by Julio.

Compiles, boots, and passes my looptorturetest.sh.
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: Julio Auto <mindvortex@gmail.com>
Cc: Solar Designer <solar@openwall.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix simple typo in RTC_HCTOSYS option.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Introduce the disable_irq_nosync_lockdep_irqsave() and
enable_irq_lockdep_irqrestore() APIs.  These are needed for NE2000; basically
NE2000 calls disable_irq and enable_irq as locking against the IRQ handler,
but both in cases where interrupts are on and off.  This means that lockdep
needs to track the old state of the virtual irq flags on disable_irq, and
restore these at enable_irq time.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If your driver implements "break on" and "break off" this ensures you won't
get multiple overlapping requests or requests in parallel.  If your driver
has its own break handling then its still your problem as the driver
author.

Break is also now serialized against writes from user space properly but no
new guarantees are made driver level about writes from the line discipline
itself (eg flow control or echo)
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

[akpm@osdl.org: build fix]
[akpm@osdl.org: warning fix]
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently this module just returns 1 if anything on module init fails. Store
the error code of the different function calls and return their error on
problems.
Signed-off-by: NRolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
[ Fixed to not unregister twice on error ]
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

[akpm@osdl.org: fix]
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Now we lock the set ioctl its trivial to lock the get one so the data
copied is consistent.  At the moment we have the BKL here but this removes
the need for it and is a step in the right direction
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Memory leaks can happen in the vc_resize() function in drivers/char/vt.c
because of the vc->vc_screenbuf variable overriding in vc_allocate().  The
kmemleak reported trace is as follows:

  <__kmalloc>
  <vc_resize>
  <fbcon_init>
  <visual_init>
  <vc_allocate>
  <con_open>
  <tty_open>
  <chrdev_open>

This patch no longer allocates a screen buffer in vc_allocate() if it was
already allocated by vc_resize().
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: N"Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix the Kconfig entry for console on AMBA PL011 to match the code.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>