Positive return values are also failures that don't set val,
although this probably can't happen. Fixes gcc 10 warning:

drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
 3747 |  *phy_fw_ver = val;

Fixes: 01b69614 ("cxgb4: Add PHY firmware support for T420-BT cards")
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow all the RGMII modes to be used.  (Not only "rgmii", "rgmii-id"
but "rgmii-txid", "rgmii-rxid")
Signed-off-by: NAtsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
mv88e6xxx fixed link fixes

Recent changes for how the MAC is configured broke fixed links, as
used by CPU/DSA ports, and for SFPs when phylink cannot be used. The
first fix is unchanged from v1. The second fix takes a different
solution than v1. If a CPU or DSA port is known to have a PHYLINK
instance, configure the port down before instantiating the PHYLINK, so
it is in the down state as expected by PHYLINK.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSA and CPU ports can be configured in two ways. By default, the
driver should configure such ports to there maximum bandwidth. For
most use cases, this is sufficient. When this default is insufficient,
a phylink instance can be bound to such ports, and phylink will
configure the port, e.g. based on fixed-link properties. phylink
assumes the port is initially down. Given that the driver should have
already configured it to its maximum speed, ask the driver to down
the port before instantiating the phylink instance.

Fixes: 30c4a5b0 ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88e6185 is reporting it has detected a PHY, when a port is
connected to an SFP. As a result, the fixed-phy configuration is not
being applied. That then breaks packet transfer, since the port is
reported as being down.

Add additional conditions to check the interface mode, and if it is
fixed always configure the port on link up/down, independent of the
PPU status.

Fixes: 30c4a5b0 ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: address automated build complaints

Kernel build checks found a couple of things to improve.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove an unused initialized value.

Fixes: 7e4d4759 ("ionic: replay filters after fw upgrade")
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the appropriate header for using dynamic_hex_dump(), which
seems to be incidentally included in some configurations but
not all.

Fixes: 7e4d4759 ("ionic: replay filters after fw upgrade")
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the DATA packet transmission to disable nofrag for UDPv4 on an AF_INET6
socket as well as UDPv6 when trying to transmit fragmentably.

Without this, packets filled to the normal size used by the kernel AFS
client of 1412 bytes be rejected by udp_sendmsg() with EMSGSIZE
immediately.  The ->sk_error_report() notification hook is called, but
rxrpc doesn't generate a trace for it.

This is a temporary fix; a more permanent solution needs to involve
changing the size of the packets being filled in accordance with the MTU,
which isn't currently done in AF_RXRPC.  The reason for not doing so was
that, barring the last packet in an rx jumbo packet, jumbos can only be
assembled out of 1412-byte packets - and the plan was to construct jumbos
on the fly at transmission time.

Also, there's no point turning on IPV6_MTU_DISCOVER, since IPv6 has to
engage in this anyway since fragmentation is only done by the sender.  We
can then condense the switch-statement in rxrpc_send_data_packet().

Fixes: 75b54cb5 ("rxrpc: Add IPv6 support")
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

KSZ9131 will not work with some switches due to workaround for KSZ9031
introduced in commit d2fd719b
("net/phy: micrel: Add workaround for bad autoneg").
Use genphy_read_status instead of dedicated ksz9031_read_status.

Fixes: bff5b4b3 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: NAtsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-2020-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.7

First set of fixes for v5.6. Fixes for a crash and for two compiler
warnings.

brcmfmac

* fix a crash related to monitor interface

ath11k

* fix compiler warnings without CONFIG_THERMAL

rtw88

* fix compiler warnings related to suspend and resume functions
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rtw88 driver defines emtpy functions with multiple indirections
but gets one of these wrong:

drivers/net/wireless/realtek/rtw88/pci.c:1347:12: error: 'rtw_pci_resume' defined but not used [-Werror=unused-function]
 1347 | static int rtw_pci_resume(struct device *dev)
      |            ^~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/pci.c:1342:12: error: 'rtw_pci_suspend' defined but not used [-Werror=unused-function]
 1342 | static int rtw_pci_suspend(struct device *dev)

Better simplify it to rely on the conditional reference in
SIMPLE_DEV_PM_OPS(), and mark the functions as __maybe_unused to avoid
warning about it.

I'm not sure if these are needed at all given that the functions
don't do anything, but they were only recently added.

Fixes: 44bc17f7 ("rtw88: support wowlan feature for 8822c")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200408185413.218643-1-arnd@arndb.de

s/mvmeta/mvneta/
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mptcp_connect/28740 is trying to release lock (sk_lock-AF_INET) at:
[<ffffffff82c15869>] mptcp_poll+0xb9/0x550
but there are no more locks to release!
Call Trace:
 lock_release+0x50f/0x750
 release_sock+0x171/0x1b0
 mptcp_poll+0xb9/0x550
 sock_poll+0x157/0x470
 ? get_net_ns+0xb0/0xb0
 do_sys_poll+0x63c/0xdd0

Problem is that __mptcp_tcp_fallback() releases the mptcp socket lock,
but after recent change it doesn't do this in all of its return paths.

To fix this, remove the unlock from __mptcp_tcp_fallback() and
always do the unlock in the caller.

Also add a small comment as to why we have this
__mptcp_needs_tcp_fallback().

Fixes: 0b4f33de ("mptcp: fix tcp fallback crash")
Reported-by: syzbot+e56606435b7bfeea8cf5@syzkaller.appspotmail.com
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows netif_receive_generic_xdp() to correctly determine the RX
queue from which the skb is coming, so that the context passed to the
XDP program will contain the correct RX queue index.
Signed-off-by: NGilberto Bertin <me@jibi.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.

Fixes: a646d6ec ("soc: qcom: ipa: modem and microcontroller")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The variable tmp64 is being initialized with a value that is never read
and it is being updated later with a new value.  The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The negotiation of flow control / pause frame modes was broken since
commit fcf1f59a ("net: phy: marvell: rearrange to use
genphy_read_lpa()") moved the setting of phydev->duplex below the
phy_resolve_aneg_pause call. Due to a check of DUPLEX_FULL in that
function, phydev->pause was no longer set.

Fix it by moving the parsing of the status variable before the blocks
dealing with the pause frames.

As the Marvell 88E1510 datasheet does not specify the timing between the
link status and the "Speed and Duplex Resolved" bit, we have to force
the link down as long as the resolved bit is not set, to avoid reporting
link up before we even have valid Speed/Duplex.

Tested with a Marvell 88E1510 (RGMII to Copper/1000Base-T)

Fixes: fcf1f59a ("net: phy: marvell: rearrange to use genphy_read_lpa()")
Signed-off-by: NClemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Add the full net DIM API to the net_dim.rst file.
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Convert the Dynamic Interrupt Moderation doc to RST and
use the RST features like syntax highlight, function and
structure documentation, enumerations, table of contents.
Reviewed-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf 2020-04-10

The following pull-request contains BPF updates for your *net* tree.

We've added 13 non-merge commits during the last 7 day(s) which contain
a total of 13 files changed, 137 insertions(+), 43 deletions(-).

The main changes are:

1) JIT code emission fixes for riscv and arm32, from Luke Nelson and Xi Wang.

2) Disable vmlinux BTF info if GCC_PLUGIN_RANDSTRUCT is used, from Slava Bacherikov.

3) Fix oob write in AF_XDP when meta data is used, from Li RongQing.

4) Fix bpf_get_link_xdp_id() handling on single prog when flags are specified,
   from Andrey Ignatov.

5) Fix sk_assign() BPF helper for request sockets that can have sk_reuseport
   field uninitialized, from Joe Stringer.

6) Fix mprotect() test case for the BPF LSM, from KP Singh.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_IP_MULTICAST is not set and multicast ip is added to the device
with autojoin flag or when multicast ip is deleted kernel will crash.

steps to reproduce:

ip addr add 224.0.0.0/32 dev eth0
ip addr del 224.0.0.0/32 dev eth0

or

ip addr add 224.0.0.0/32 dev eth0 autojoin

Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
 pc : _raw_write_lock_irqsave+0x1e0/0x2ac
 lr : lock_sock_nested+0x1c/0x60
 Call trace:
  _raw_write_lock_irqsave+0x1e0/0x2ac
  lock_sock_nested+0x1c/0x60
  ip_mc_config.isra.28+0x50/0xe0
  inet_rtm_deladdr+0x1a8/0x1f0
  rtnetlink_rcv_msg+0x120/0x350
  netlink_rcv_skb+0x58/0x120
  rtnetlink_rcv+0x14/0x20
  netlink_unicast+0x1b8/0x270
  netlink_sendmsg+0x1a0/0x3b0
  ____sys_sendmsg+0x248/0x290
  ___sys_sendmsg+0x80/0xc0
  __sys_sendmsg+0x68/0xc0
  __arm64_sys_sendmsg+0x20/0x30
  el0_svc_common.constprop.2+0x88/0x150
  do_el0_svc+0x20/0x80
 el0_sync_handler+0x118/0x190
  el0_sync+0x140/0x180

Fixes: 93a714d6 ("multicast: Extend ip address command to enable multicast group join/leave on")
Signed-off-by: NTaras Chornyi <taras.chornyi@plvision.eu>
Signed-off-by: NVadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rds_free_mr(), it calls rds_destroy_mr(mr) directly.  But this
defeats the purpose of reference counting and makes MR free handling
impossible.  It means that holding a reference does not guarantee that
it is safe to access some fields.  For example, In
rds_cmsg_rdma_dest(), it increases the ref count, unlocks and then
calls mr->r_trans->sync_mr().  But if rds_free_mr() (and
rds_destroy_mr()) is called in between (there is no lock preventing
this to happen), r_trans_private is set to NULL, causing a panic.
Similar issue is in rds_rdma_unuse().
Reported-by: Nzerons <sironhide0null@gmail.com>
Signed-off-by: NKa-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And removed rds_mr_put().
Signed-off-by: NKa-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the macsec_changelink(), "struct macsec_tx_sa tx_sc" is used to
store "macsec_secy.tx_sc".
But, the struct type of tx_sc is macsec_tx_sc, not macsec_tx_sa.
So, the macsec_tx_sc should be used instead.

Test commands:
    ip link add dummy0 type dummy
    ip link add macsec0 link dummy0 type macsec
    ip link set macsec0 type macsec encrypt off

Splat looks like:
[61119.963483][ T9335] ==================================================================
[61119.964709][ T9335] BUG: KASAN: slab-out-of-bounds in macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.965787][ T9335] Read of size 160 at addr ffff888020d69c68 by task ip/9335
[61119.966699][ T9335]
[61119.966979][ T9335] CPU: 0 PID: 9335 Comm: ip Not tainted 5.6.0+ #503
[61119.967791][ T9335] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[61119.968914][ T9335] Call Trace:
[61119.969324][ T9335]  dump_stack+0x96/0xdb
[61119.969809][ T9335]  ? macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.970554][ T9335]  print_address_description.constprop.5+0x1be/0x360
[61119.971294][ T9335]  ? macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.971973][ T9335]  ? macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.972703][ T9335]  __kasan_report+0x12a/0x170
[61119.973323][ T9335]  ? macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.973942][ T9335]  kasan_report+0xe/0x20
[61119.974397][ T9335]  check_memory_region+0x149/0x1a0
[61119.974866][ T9335]  memcpy+0x1f/0x50
[61119.975209][ T9335]  macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.975825][ T9335]  ? macsec_get_stats64+0x3e0/0x3e0 [macsec]
[61119.976451][ T9335]  ? kernel_text_address+0x111/0x120
[61119.976990][ T9335]  ? pskb_expand_head+0x25f/0xe10
[61119.977503][ T9335]  ? stack_trace_save+0x82/0xb0
[61119.977986][ T9335]  ? memset+0x1f/0x40
[61119.978397][ T9335]  ? __nla_validate_parse+0x98/0x1ab0
[61119.978936][ T9335]  ? macsec_alloc_tfm+0x90/0x90 [macsec]
[61119.979511][ T9335]  ? __kasan_slab_free+0x111/0x150
[61119.980021][ T9335]  ? kfree+0xce/0x2f0
[61119.980700][ T9335]  ? netlink_trim+0x196/0x1f0
[61119.981420][ T9335]  ? nla_memcpy+0x90/0x90
[61119.982036][ T9335]  ? register_lock_class+0x19e0/0x19e0
[61119.982776][ T9335]  ? memcpy+0x34/0x50
[61119.983327][ T9335]  __rtnl_newlink+0x922/0x1270
[ ... ]

Fixes: 3cf3227a ("net: macsec: hardware offloading infrastructure")
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable ret is being initialized with a value that is never read
and it is being updated later with a new value.  The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the local node id(qrtr_local_nid) is not modified after its
initialization, it equals to the broadcast node id(QRTR_NODE_BCAST).
So the messages from local node should not be taken as broadcast
and keep the process going to send them out anyway.

The definitions are as follow:
static unsigned int qrtr_local_nid = NUMA_NO_NODE;

Fixes: fdf5fd39 ("net: qrtr: Broadcast messages only from control port")
Signed-off-by: NWang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2020-04-08

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v5.3
 ('net/mlx5: Fix frequent ioread PCI access during recovery')
 ('net/mlx5e: Add missing release firmware call')

For -stable v5.4
 ('net/mlx5e: Fix nest_level for vlan pop action')
 ('net/mlx5e: Fix pfnum in devlink port attribute')
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At 'make htmldocs' the following warning is thrown:

Documentation/networking/devlink/devlink-trap.rst:302:
WARNING: undefined label: generic-packet-trap-groups

Fixes the warning by setting the label to the specified header,
within the same document.
Signed-off-by: NLothar Rubusch <l.rubusch@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current arm BPF JIT does not correctly compile RSH or ARSH when the
immediate shift amount is 0. This causes the "rsh64 by 0 imm" and "arsh64
by 0 imm" BPF selftests to hang the kernel by reaching an instruction
the verifier determines to be unreachable.

The root cause is in how immediate right shifts are encoded on arm.
For LSR and ASR (logical and arithmetic right shift), a bit-pattern
of 00000 in the immediate encodes a shift amount of 32. When the BPF
immediate is 0, the generated code shifts by 32 instead of the expected
behavior (a no-op).

This patch fixes the bugs by adding an additional check if the BPF
immediate is 0. After the change, the above mentioned BPF selftests pass.

Fixes: 39c13c20 ("arm: eBPF JIT compiler")
Co-developed-by: NXi Wang <xi.wang@gmail.com>
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Signed-off-by: NLuke Nelson <luke.r.nels@gmail.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200408181229.10909-1-luke.r.nels@gmail.com

In testing, we found that for request sockets the sk->sk_reuseport field
may yet be uninitialized, which caused bpf_sk_assign() to randomly
succeed or return -ESOCKTNOSUPPORT when handling the forward ACK in a
three-way handshake.

Fix it by only applying the reuseport check for full sockets.

Fixes: cf7fbe66 ("bpf: Add socket assign support")
Signed-off-by: NJoe Stringer <joe@wand.net.nz>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NMartin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200408033540.10339-1-joe@wand.net.nz

Fixes CT entries list corruption.

After allowing parallel insertion/removals in upper nf flow table
layer, unprotected ct entries list can be corrupted by parallel add/del
on the same flow table.

CT entries list is only used while freeing a ct zone flow table to
go over all the ct entries offloaded on that zone/table, and flush
the table.

As rhashtable already provides an api to go over all the inserted entries,
fix the race by using the rhashtable iteration instead, and remove the list.

Fixes: 7da182a9 ("netfilter: flowtable: Use work entry per offload command")
Reviewed-by: NOz Shlomo <ozsh@mellanox.com>
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In cited commit netdevice is registered after devlink port.

Unregistration flow should be mirror sequence of registration flow.
Hence, unregister netdevice before devlink port.

Fixes: 31e87b39 ("net/mlx5e: Fix devlink port register sequence")
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Cited patch missed to extract PCI pf number accurately for PF and VF
port flavour. It considered PCI device + function number.
Due to this, device having non zero device number shown large pfnum.

Hence, use only PCI function number; to avoid similar errors, derive
pfnum one time for all port flavours.

Fixes: f60f315d ("net/mlx5e: Register devlink ports for physical link, PCI PF, VFs")
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

With ct clear action we should not allocate the action in hw
and not release the mod_acts parsed in advance.
It will be done when handling the ct clear action.

Fixes: 1ef3018f ("net/mlx5e: CT: Support clear action")
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Current value of nest_level, assigned from net_device lower_level value,
does not reflect the actual number of vlan headers, needed to pop.
For ex., if we have untagged ingress traffic sended over vlan devices,
instead of one pop action, driver will perform two pop actions.
To fix that, calculate nest_level as difference between vlan device and
parent device lower_levels.

Fixes: f3b0a18b ("net: remove unnecessary variables and callback")
Signed-off-by: NDmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Once driver finishes flashing the firmware image, it should release it.

Fixes: 9c8bca26 ("mlx5: Move firmware flash implementation to devlink")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NAya Levin <ayal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When we destroy rules from slow path we need to avoid destroying
termination tables since termination tables are never created in slow
path. By doing so we avoid destroying the termination table created for the
slow path.

Fixes: d8a2034f ("net/mlx5: Don't use termination tables in slow path")
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NOz Shlomo <ozsh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

High frequency of PCI ioread calls during recovery flow may cause the
following trace on powerpc:

[ 248.670288] EEH: 2100000 reads ignored for recovering device at
location=Slot1 driver=mlx5_core pci addr=0000:01:00.1
[ 248.670331] EEH: Might be infinite loop in mlx5_core driver
[ 248.670361] CPU: 2 PID: 35247 Comm: kworker/u192:11 Kdump: loaded
Tainted: G OE ------------ 4.14.0-115.14.1.el7a.ppc64le #1
[ 248.670425] Workqueue: mlx5_health0000:01:00.1 health_recover_work
[mlx5_core]
[ 248.670471] Call Trace:
[ 248.670492] [c00020391c11b960] [c000000000c217ac] dump_stack+0xb0/0xf4
(unreliable)
[ 248.670548] [c00020391c11b9a0] [c000000000045818]
eeh_check_failure+0x5c8/0x630
[ 248.670631] [c00020391c11ba50] [c00000000068fce4]
ioread32be+0x114/0x1c0
[ 248.670692] [c00020391c11bac0] [c00800000dd8b400]
mlx5_error_sw_reset+0x160/0x510 [mlx5_core]
[ 248.670752] [c00020391c11bb60] [c00800000dd75824]
mlx5_disable_device+0x34/0x1d0 [mlx5_core]
[ 248.670822] [c00020391c11bbe0] [c00800000dd8affc]
health_recover_work+0x11c/0x3c0 [mlx5_core]
[ 248.670891] [c00020391c11bc80] [c000000000164fcc]
process_one_work+0x1bc/0x5f0
[ 248.670955] [c00020391c11bd20] [c000000000167f8c]
worker_thread+0xac/0x6b0
[ 248.671015] [c00020391c11bdc0] [c000000000171618] kthread+0x168/0x1b0
[ 248.671067] [c00020391c11be30] [c00000000000b65c]
ret_from_kernel_thread+0x5c/0x80

Reduce the PCI ioread frequency during recovery by using msleep()
instead of cond_resched()

Fixes: 3e5b72ac ("net/mlx5: Issue SW reset on FW assert")
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Reviewed-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>