This patch (as1623) removes the ehci_port_power() routine and all the
places that call it.  There's no reason for ehci-hcd to change the
port power settings; the hub driver takes care of all that stuff.

There is one exception: When the controller is resumed from
hibernation or following a loss of power, the ports that are supposed
to be handed over to a companion controller must be powered on first.
Otherwise the handover won't work.  This process is not visible to the
hub driver, so it has to be handled in ehci-hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1622) removes the USB-2.1 Link Power Management code
from the ehci-hcd driver.  This code was never integrated with
usbcore, it is full of bugs, and it was not getting used by anybody.

However, the debugging code for dumping the LPM-related fields in the
EHCI registers is left in place.  In theory it might be useful to see
these values, even though we don't use them.

This essentially amounts to a partial revert of commit
aa4d8342 (USB: EHCI: EHCI 1.1
addendum: preparation) and an almost full revert of commit
48f24970 (USB: EHCI: EHCI 1.1
addendum: Basic LPM feature support) plus its follow-ons.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1621) removes the limit on the number of loops allowed
in hub_tt_work().  The value is arbitrary, and it's silly to have a
limit in the first place -- anything beyond the limit would not get
handled.

Besides, it's most unlikely that we'll ever need to clear more than a
couple of TT buffers at any time.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove all MODULE_VERSION macros and driver-version information (except
for garmin_gps which uses it in a status reply).

It is the kernel version that matters and not some private version
scheme which rarely even gets updated.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When rts51x_read_status() returns USB_STOR_TRANSPORT_ERROR,
an error happens. This patch fixes build warning as below:

drivers/usb/storage/realtek_cr.c: In function 'init_realtek_cr':
drivers/usb/storage/realtek_cr.c:476:33: warning: 'buf[15]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[15]' was declared here
drivers/usb/storage/realtek_cr.c:475:33: warning: 'buf[14]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[14]' was declared here
drivers/usb/storage/realtek_cr.c:474:50: warning: 'buf[13]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[13]' was declared here
drivers/usb/storage/realtek_cr.c:472:30: warning: 'buf[12]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[12]' was declared here
drivers/usb/storage/realtek_cr.c:471:31: warning: 'buf[11]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[11]' was declared here
drivers/usb/storage/realtek_cr.c:470:31: warning: 'buf[10]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[10]' was declared here
drivers/usb/storage/realtek_cr.c:469:30: warning: 'buf[9]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[9]' was declared here
drivers/usb/storage/realtek_cr.c:468:27: warning: 'buf[8]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[8]' was declared here
drivers/usb/storage/realtek_cr.c:468:43: warning: 'buf[7]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[7]' was declared here
drivers/usb/storage/realtek_cr.c:467:30: warning: 'buf[6]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[6]' was declared here
drivers/usb/storage/realtek_cr.c:466:30: warning: 'buf[5]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[5]' was declared here
drivers/usb/storage/realtek_cr.c:465:28: warning: 'buf[4]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[4]' was declared here
drivers/usb/storage/realtek_cr.c:464:24: warning: 'buf[3]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[3]' was declared here
drivers/usb/storage/realtek_cr.c:464:40: warning: 'buf[2]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[2]' was declared here
drivers/usb/storage/realtek_cr.c:463:24: warning: 'buf[1]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[1]' was declared here
drivers/usb/storage/realtek_cr.c:463:40: warning: 'buf[0]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[0]' was declared here
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use ftdi_get_modem_status to check hardware buffers in chars_in_buffer.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No need to check hardware buffers when we know that the software
buffers are non-empty.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use generic chars_in_buffer rather than copying it's implementation.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Export generic chars_in_buffer implementation so it can be used in
subdrivers in combination with checks of any hardware buffers.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor modem-control status retrieval.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure we do not return USB-internal error codes to userspace.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Align the modem-control status operands as was originally indented.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove unused port field from private port data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since there's no possible caller of dbgp_external_startup() and
dbgp_reset_prep() when !USB_EHCI_HCD, there's no point in building and
exporting these functions in that case. This eliminates a build error
under the conditions listed in the subject, introduced with the merge
f1c6872e.
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No need to memset a kzalloced struct.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix missing and superfluous whitespace.
Fix misplaced brackets.
Fix indentation.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This change correctly computes the header length and data length in
the fragments to avoid a bug where we would end up with extremely
slow performance.  Also adopt use of skb_frag_size() accessor.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org [v3.6]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These devices provide QMI and ethernet functionality via a standard CDC
ethernet descriptor.  But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface.  Thus blacklist the devices in cdc_ether and add their IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver anchors the tx urbs and defers the urb submission if
a transmit request comes when the interface is suspended.
Anchoring urb increments the urb reference count. These
deferred urbs are later accessed by calling usb_get_from_anchor()
for submission during interface resume. usb_get_from_anchor()
unanchors the urb but urb reference count remains same.
This causes the urb reference count to remain non-zero
after usb_free_urb() gets called and urb never gets freed.
Hence call usb_put_urb() after anchoring the urb to properly
balance the reference count for these deferred urbs. Also,
unanchor these deferred urbs during disconnect, to free them
up.
Signed-off-by: NHemant Kumar <hemantk@codeaurora.org>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a failure takes place during the EQ creation, we need to unmap the
UAR memory block too.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NUri Habusha <urih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan tag can be zero. This is why it can't serve as an indication
that packet requires VLAN header in the TX flow.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).

Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The delayed work function int_in_work() may call usb_reset_device()
and thus, indirectly, the driver's pre_reset method. Trying to
cancel the work synchronously in that situation would deadlock.
Fix by avoiding cancel_work_sync() in the pre_reset method.

If the reset was NOT initiated by int_in_work() this might cause
int_in_work() to run after the post_reset method, with urb_int_in
already resubmitted, so handle that case gracefully.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We handle NOTIFY_THROTTLING so don't then fall through to unsupported event.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Decode multitouch reports from the touch sensor of the Cintiq 24HD
touch.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Like our other pen-and-touch products, the Cintiq 24HD touch needs data
to be shared between its two sensors to facilitate proximity-based palm
rejection.

Unlike other tablets that report sensor data through separate interfaces
of the same USB device, the Cintiq 24HD touch has separate USB devices
that are connected to an internal USB hub.

This patch makes it possible to designate the USB VID/PID of the other
device so that the two may share data.  To ensure we don't accidentally
link to a sensor from a physically separate device (if several have been
plugged in), we limit the search to siblings (i.e., devices directly
connected to the same hub).
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Tested-by: NRoland Stigge <stigge@antcom.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The dw_dmac driver was originally developed for avr32 to be used with the
Synopsys DesignWare AHB DMA controller.  Starting from 2.6.38, access to
the device's i/o memory was done with the little-endian readl/writel
functions(1)

This broke the driver for the avr32 platform, because it needs big
(native) endian accessors.  This patch makes the endianness configurable
using 'DW_DMAC_BIG_ENDIAN_IO', which will default be true for AVR32

I submitted this patch before(2) but then waited for Andy to finish other
changes to the same module(3).

(1) https://patchwork.kernel.org/patch/608211
(2) https://lkml.org/lkml/2012/8/26/148
(3) https://lkml.org/lkml/2012/9/21/173Signed-off-by: NHein Tibosch <hein_tibosch@yahoo.es>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Havard Skinnemoen <havard@skinnemoen.net>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add this missing SPI dependency and prevent the driver from building
without SPI, because functions of the spi driver are used in this
driver.

  drivers/video/backlight/ili9320.c:51: undefined reference to `spi_sync'

Also, a prompt string for CONFIG_LCD_ILI9320 is added for explicit
selection.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the variable ep_ctx from xhci_add_endpoint(), since it is
assigned but unused.  Caught by Coverity.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Remove the variable slot_ctx from xhci_dbg_ctx(), since it is assigned
but unused.  Caught by Coverity.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Coverity complains that xhci_evaluate_context_result() is missing a
break statement after the COMP_EBADSLT switch case.  It's not a big
deal, since we wanted to return the same error code as the case
statement below it does.  The end result would be one that a Slot
Disabled error completion code would also print the warning message
associated with a Context State error code.  No other bad behavior would
result.

It's not worth backporting to stable kernels, since it only fixes an
issue with too much debugging.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The command cancellation code doesn't check whether find_trb_seg()
couldn't find the segment that contains the TRB to be canceled.  This
could cause a NULL pointer deference later in the function when next_trb
is called.  It's unlikely to happen unless something is wrong with the
command ring pointers, so add some debugging in case it happens.

This patch should be backported to stable kernels as old as 3.0, that
contain the commit b63f4053 "xHCI:
handle command after aborting the command ring".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This will fix warnings like following when CONFIG_PM_SLEEP is not set:

        warning: 'xxx_suspend' defined but not used [-Wunused-function]
        warning: 'xxx_resume' defined but not used [-Wunused-function]

Because
	SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)

Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).

Cc: Mattia Dongili <malattia@linux.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This uses irq_of_parse_and_map instead of of_irq_map_one and
irq_create_of_mapping.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch sets hub device's default autosuspend delay as 0 to
speedup bus suspend, see comments in code for details.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The hub status endpoint has a long 'bInterval', which is 255ms
for FS/LS device and 256ms for HS device according to USB 2.0 spec,
so the device connection change may be reported later more than 255ms
via status pipe.

The connection change in hub may have been happened already on the
downstream ports, but no status URB completes when it is killed
in hub_suspend(auto), so the connection change may be missed by some
buggy hub devices, which won't generate remote wakeup signal after
their remote wakeup is enabled and they are put into suspend state.

The problem can be observed at least on the below Genesys Logic, Inc.
hub devices:

	0x05e3,0x0606
	0x05e3,0x0608

In theory, there is no way to fix the problem completely, but we
can make it less likely to occur by this patch.

This patch introduces one quirk of HUB_QUIRK_CHECK_PORTS_AUTOSUSPEND
to check ports' change during hub_suspend(auto) for the buggy
devices. If ports' change is found, terminate the auto suspend and
return to working state.

So for the buggy hubs, if the connection change happend before
the ports' check, it can be handled correctly. If it happens between
the ports' check and enabling remote wakeup/entering suspend, it
will be missed. Considered the interval is quite short, it is very
less likely to happen during the window.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Board name changed on another shipping Lucid tablet.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Cc: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>