Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Engine fields have been removed, as they're specified by PTOP.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Ported from the code currently in engine/fifo/gk104.c.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Add a basic clock driver that reuses the GK20A logic.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Add basic GM20B volt driver that reuses the GK20A logic.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The HW accepts KeplerDmaCopyA and MaxwellDmaCopyA classes.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This class supports a WFI method (0x0078) that's not present on the
KeplerChannelGpfifoA class.

The binary driver exposes both classes on these GPUs for some reason,
though there doesn't appear to be any difference in the setup that's
done for each (ie. even if you allocate GpfifoA, the WFI method will
still work).

We shall just expose GpfifoB, as I don't see a good reason to report
the presence of both.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

based on Martins initial work

v3: fix ina2x9 calculations
v4: don't kmalloc(0), fix the lsb/pga stuff
v5: add a field to tell if the power reading may be invalid
    add nkvm_iccsense_read_all function
    check for the device on the i2c bus
Signed-off-by: NKarol Herbst <nouveau@karolherbst.de>
Reviewed-by: NMartin Peres <martin.peres@free.fr>

Signed-off-by: NKarol Herbst <nouveau@karolherbst.de>
Reviewed-by: NMartin Peres <martin.peres@free.fr>

Add secure boot support for the GM20B chip found in Tegra X1. Secure
boot on Tegra works slightly differently from desktop, notably in the
way the WPR region is set up.

In addition, the firmware bootloaders use a slightly different header
format.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Add secure-boot for the dGPU set of GM20X chips, using the PMU as the
high-secure falcon.

This work is based on Deepak Goyal's initial port of Secure Boot to
Nouveau.

v2. use proper memory target function
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

On GM200 and later GPUs, firmware for some essential falcons (notably
GR ones) must be authenticated by a NVIDIA-produced signature and
loaded by a high-secure falcon in order to be able to access privileged
registers, in a process known as Secure Boot.

Secure Boot requires building a binary blob containing the firmwares
and signatures of the falcons to be loaded. This blob is then given to
a high-secure falcon running a signed loader firmware that copies the
blob into a write-protected region, checks that the signatures are
valid, and finally loads the verified firmware into the managed falcons
and switches them to privileged mode.

This patch adds infrastructure code to support this process on chips
that require it.

v2:
- The IRQ mask of the PMU falcon was left - replace it with the proper
  irq_mask variable.
- The falcon reset procedure expecting a falcon in an initialized state,
  which was accidentally provided by the PMU subdev. Make sure that
  secboot can manage the falcon on its own.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Most of the per-chipset differences will go away when we fully switch
to using the register lists provided by the firmware files, which will
leave all the remaining code "belonging" to GM200.

This is a preemptive rename from GM204 to GM200.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

nvkm_device_fini is never called if a failure occurs in
nvkm_device_init, even when unloading the module. This can lead to a
resources leak (one example is the Tegra interrupt which would never be
freed in that case). Fix this by calling nvkm_device_fini in
nvkm_device_init's failure path.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

v2: change email used in header
v4: change Copyright information
v5: revert Copyright changes
Signed-off-by: NKarol Herbst <nouveau@karolherbst.de>

v2: change email used in header
v4: change Copyright information
v5: revert Copyright changes
Signed-off-by: NKarol Herbst <nouveau@karolherbst.de>

Differences from GM10x:
- GM20x LTC count detection differs from GM10x
- GM20x init doesn't require large page size setting
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

GM20x doesn't require the priv ring timeout bumps that GK/GM10x have.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We want to unlock nv_devices_mutex in this error path as well.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported to be needed as per fdo#70354 comment #61.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Was not able to obtain a trace of NVRM due to kernel version annoyances,
however, experimentally confirmed that the WAR we use on NV50/G8x boards
works here too.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

An upcoming patch will implement functionality that we don't use on any
NV40 chipset.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

An upcoming patch will implement functionality that we don't use on the
original NV50.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Increase clock timeout of some unknown engines in order to avoid failure
at high gpcclk rate.

This fixes IBUS read faults on my GF119 when reclocking is manually
enabled. Note that memory reclocking is completely broken and NvMemExec
has to be disabled to allow core clock reclocking only.
Signed-off-by: NSamuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

I got confirmation that we can read and change the voltage with the same code.
The divider is also computed correctly on the gm204 we got our hands on.

Thanks to Yoshimo on IRC for executing the tests on his gm204!
Signed-off-by: NMartin Peres <martin.peres@free.fr>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Let's ignore the other desktop Maxwells until I get my hands on one and confirm
that we still can change the voltage.
Signed-off-by: NMartin Peres <martin.peres@free.fr>

Most Keplers actually use the GPIO-based voltage management instead of the new
PWM-based one. Use the GPIO mode as a fallback as it already gracefully handles
the case where no GPIOs exist.

All the Maxwells seem to use the PWM method though.

v2:
 - Do not forget to commit the PWM configuration change!
Signed-off-by: NMartin Peres <martin.peres@free.fr>