There's no reason to send a delBA when the
peer refused our addBA, so change that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a station is removed and we stop the aggregation
sessions, it's not useful to send delBA since this is
due to us or the station disassociating or dropping
the connection in some other way, so change that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we disassociate, it's not really useful to
send delBA action frames since we're going to send
disassoc/deauth anyway, so change that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In the IBSS auth TX debug message the BSSID and DA
address are reversed, fix that.
Signed-off-by: NSylvain Roger Rieunier <sylvain.roger.rieunier@gmail.com>
[reword commit message and make it fit 72 cols]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The name can't be modified by the driver,
make it const.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The suspend/resume code depends on CONFIG_PM, so
the reset debugfs file can only be made available
if that is enabled.

Fengguang Wu's zero-day build testing found this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In AP mode, when a station requests connection to an AP and if the
request is failed for particular reason, userspace is notified about the
failure through NL80211_CMD_CONN_FAILED command. Reason for the failure
is sent through the attribute NL80211_ATTR_CONN_FAILED_REASON.
Signed-off-by: NPandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The kerneldoc comment for .sched_scan_stop() callback describes a
driver_initiated flag, but the interface does not hold such a flag.
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The only case where intersected_rd can become non NULL is within an if. All
paths from that if return, so the end chunk has therefore squawked its
last and is no more.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Peer link which is blocked using the "iw mesh0 station
set <MAC addr> plink_action block" is previously not able
to re-open using "iw mesh0 station set <MAC addr>
plink_action open". This patch is intended to solve this.

If the station plink state remains at OPN_SNT once open,
try block and open again should solve this problem.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make the function acquire the necessary mutex itself
to simplify the callers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, mac80211 uses the power constraint IE, and reduces
the regulatory max TX power by it. This can cause issues if
the AP is advertising a large power constraint value matching
a high TX power in its country IE, for example in this case:

...
Country: US  Environment: Indoor/Outdoor
    ...
    Channels [157 - 157] @ 30 dBm
    ...
Power constraint: 13 dB
...

What happened here is that our local regulatory TX power is
15 dBm, and gets reduced by 13 dB so we end up with only
2 dBm effective TX power, which is way too low.

Instead, handle the country IE/power constraint IE combined
and restrict our TX power to the max of the regulatory power
and the maximum power advertised by the AP, in this case
17 dBm (= 30 dBm - 13 dB).

Also print a message when this happens to let the user know
and help us debug issues with it.
Reported-by: NCarl A. Cook <CACook@quantum-equities.com>
Tested-by: NCarl A. Cook <CACook@quantum-equities.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The functions are only called if CONFIG_PM is set
as the callers are under an ifdef, so there's no
need to also define no-op functions.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

skb->dev might contain a stale reference to a device that was already
deleted, and using it unchecked can lead to invalid pointer accesses.
Since this is only used for nl80211 tx, iterate over active interfaces
to find a match for skb->dev, and discard the tx status if the device
is gone.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mac80211 calls synchronize_rcu() on sta deletion,
which increase the roaming time significantly.

Convert it into a call_rcu() mechanism, in order
to avoid blocking. Since some of the cleanup
functions might sleep, schedule from the call_rcu
callback a new work that will do the actual cleanup.

In order to make sure the cleanup occurs before
the interface went down, flush local->workqueue
on ieee80211_do_stop().
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Whenever a host gets an AUTH frame it first allocates a new
station and then replies with another AUTH frame. However,
if sta allocations fails the host should send a DEAUTH frame
instead to tell the other end that something went wrong.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
[reword commit message a bit]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move ieee80211_send_deauth_disassoc() to util.c to make it
available for the rest of the mac80211 code.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
[reword commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

removes unnecessary semicolon

Found by Coccinelle: http://coccinelle.lip6.fr/Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Split functionality for further reuse.

Will prevent code duplication when channel context
channel_type merging is introduced.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

__ieee80211_key_destroy() calls synchronize_rcu() in
order to sync the tx path before destroying the key.

However, synching the tx path can be done with
synchronize_net() as well, which is usually faster
(the timing might be important for roaming scenarios).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The power constraint IE is always a single byte
so check the size when parsing instead of later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These should be with the functions so move
the module_init/exit statements.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are a number of functions that shouldn't really
be used when modern functions that take the band are
available in cfg80211. Remove these, but for now keep
 * ieee80211_freq_to_dsss_chan and
 * ieee80211_dsss_chan_to_freq
as they're used in older drivers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Disconnect from the AP if channel switching in the
driver failed or if the new channel is unavailable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to keep a copy of the scheduled
scan IEs after the driver has been told, if it
requires a copy it must make one. Therefore, we
can move sched_scan_ies into the function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Pull in mac80211.git to let the next patch apply
without conflicts, also resolving a hwsim conflict.

Conflicts:
	drivers/net/wireless/mac80211_hwsim.c
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using list_move() instead of list_del() + list_add().

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

checkpatch pointed out an issue, fix it.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The wext code checks is the event data is within size limits.
When this check fails a message is logged with violating size.
This patch adds the event id to put us on the right track for
resolving that violation.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Various small fixes for net/mac80211/cfg.c:mpath_set_pinfo():
Initialize *pinfo before filling members in, handle MESH_PATH_RESOLVED
correctly, and remove bogus assignment; result in correct display
of FLAGS values and meaningful EXPTIME for expired paths in iw utility.
Signed-off-by: NYoichi Shinoda <shinoda@jaist.ac.jp>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Doing so creates warnings, but the function is internal and
not part of the 802.11 docbooks, so it from kerneldoc.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

connkeys is malloced in nl80211_parse_connkeys() and should
be freed in the error handling case, otherwise it will cause
memory leak.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ifmgd->bssid wasn't cleared properly in some
auth/assoc failure cases, causing mac80211 and
the low-level driver to go out of sync.

Clear ifmgd->bssid on failure, and notify the driver.

Cc: stable@kernel.org # 3.4+
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A P2P Device interface does not have a netdev, and is not
expected to be used for transmitting data, so there is no
need to assign hw queues for it.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>