When many cpus compete for sending frames on a given qdisc, the qdisc
spinlock suffers from very high contention.

The cpu owning __QDISC_STATE_RUNNING bit has same priority to acquire
the lock, and cannot dequeue packets fast enough, since it must wait for
this lock for each dequeued packet.

One solution to this problem is to force all cpus spinning on a second
lock before trying to get the main lock, when/if they see
__QDISC_STATE_RUNNING already set.

The owning cpu then compete with at most one other cpu for the main
lock, allowing for higher dequeueing rate.

Based on a previous patch from Alexander Duyck. I added the heuristic to
avoid the atomic in fast path, and put the new lock far away from the
cache line used by the dequeue worker. Also try to release the busylock
lock as late as possible.

Tests with following script gave a boost from ~50.000 pps to ~600.000
pps on a dual quad core machine (E5450 @3.00GHz), tg3 driver.
(A single netperf flow can reach ~800.000 pps on this platform)

for j in `seq 0 3`; do
  for i in `seq 0 7`; do
    netperf -H 192.168.0.1 -t UDP_STREAM -l 60 -N -T $i -- -m 6 &
  done
done
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__QDISC_STATE_RUNNING is always changed while qdisc lock is held.

We can avoid two atomic operations in xmit path, if we move this bit in
a new __state container.

Location of this __state container is carefully chosen so that fast path
only dirties one qdisc cache line.

THROTTLED bit could later be moved into this __state location too, to
avoid dirtying first qdisc cache line.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define three helpers to manipulate QDISC_STATE_RUNNIG flag, that a
second patch will move on another location.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently such notifications are only generated when the device comes up or the
address changes. However one use case for these notifications is to enable
faster network recovery after a virtual machine migration (by causing switches
to relearn their MAC tables). A migration appears to the network stack as a
temporary loss of carrier and therefore does not trigger either of the current
conditions. Rather than adding carrier up as a trigger (which can cause issues
when interfaces a flapping) simply add an interface which the driver can use
to explicitly trigger the notification.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bunch of new rapidio kernel-doc warnings:

Warning(include/linux/rio.h:123): No description found for parameter 'comp_tag'
Warning(include/linux/rio.h:123): No description found for parameter 'phys_efptr'
Warning(include/linux/rio.h:123): No description found for parameter 'em_efptr'
Warning(include/linux/rio.h:123): No description found for parameter 'pwcback'
Warning(include/linux/rio.h:247): No description found for parameter 'set_domain'
Warning(include/linux/rio.h:247): No description found for parameter 'get_domain'
Warning(drivers/rapidio/rio-scan.c:1133): No description found for parameter 'rdev'
Warning(drivers/rapidio/rio-scan.c:1133): Excess function parameter 'port' description in 'rio_init_em'
Warning(drivers/rapidio/rio.c:349): No description found for parameter 'rdev'
Warning(drivers/rapidio/rio.c:349): Excess function parameter 'mport' description in 'rio_request_inb_pwrite'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'port'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'local'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'destid'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'hopcount'
Warning(drivers/rapidio/rio.c:393): Excess function parameter 'rdev' description in 'rio_mport_get_physefb'
Warning(drivers/rapidio/rio.c:845): Excess function parameter 'local' description in 'rio_std_route_clr_table'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 0ac0c0d0, which
caused cross-architecture build problems for all the wrong reasons.
IA64 already added its own version of __node_random(), but the fact is,
there is nothing architectural about the function, and the original
commit was just badly done. Revert it, since no fix is forthcoming.
Requested-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 756dee75 ("SLUB: Get rid of dynamic DMA
kmalloc cache allocation") makes S390 run out of kmalloc caches.  Increase the
number of kmalloc caches to a safe size.

Cc: <stable@kernel.org> [ .33 and .34 ]
Reported-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Tested-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NChristoph Lameter <cl@linux-foundation.org>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

Add missing _killable_timeout variant for wait_for_completion that will
return when a timeout expires or the task is killed.

CC: Ingo Molnar <mingo@elte.hu>
CC: Andreas Herrmann <andreas.herrmann3@amd.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Mike Galbraith <efault@gmx.de>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NSage Weil <sage@newdream.net>

Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a new truncate calling sequence into fs/mm subsystems. Rather than
setattr > vmtruncate > truncate, have filesystems call their truncate sequence
from ->setattr if filesystem specific operations are required. vmtruncate is
deprecated, and truncate_pagecache and inode_newsize_ok helpers introduced
previously should be used.

simple_setattr is introduced for simple in-ram filesystems to implement
the new truncate sequence. Eventually all filesystems should be converted
to implement a setattr, and the default code in notify_change should go
away.

simple_setsize is also introduced to perform just the ATTR_SIZE portion
of simple_setattr (ie. changing i_size and trimming pagecache).

To implement the new truncate sequence:
- filesystem specific manipulations (eg freeing blocks) must be done in
  the setattr method rather than ->truncate.
- vmtruncate can not be used by core code to trim blocks past i_size in
  the event of write failure after allocation, so this must be performed
  in the fs code.
- convert usage of helpers block_write_begin, nobh_write_begin,
  cont_write_begin, and *blockdev_direct_IO* to use _newtrunc postfixed
  variants. These avoid calling vmtruncate to trim blocks (see previous).
- inode_setattr should not be used. generic_setattr is a new function
  to be used to copy simple attributes into the generic inode.
- make use of the better opportunity to handle errors with the new sequence.

Big problem with the previous calling sequence: the filesystem is not called
until i_size has already changed.  This means it is not allowed to fail the
call, and also it does not know what the previous i_size was. Also, generic
code calling vmtruncate to truncate allocated blocks in case of error had
no good way to return a meaningful error (or, for example, atomically handle
block deallocation).

Cc: Christoph Hellwig <hch@lst.de>
Acked-by: NJan Kara <jack@suse.cz>
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

We don't name our generic fsync implementations very well currently.
The no-op implementation for in-memory filesystems currently is called
simple_sync_file which doesn't make too much sense to start with,
the the generic one for simple filesystems is called simple_fsync
which can lead to some confusion.

This patch renames the generic file fsync method to generic_file_fsync
to match the other generic_file_* routines it is supposed to be used
with, and the no-op implementation to noop_fsync to make it obvious
what to expect.  In addition add some documentation for both methods.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

__aio_put_req() plays sick games with file refcount.  What
it wants is fput() from atomic context; it's almost always
done with f_count > 1, so they only have to deal with delayed
work in rare cases when their reference happens to be the
last one.  Current code decrements f_count and if it hasn't
hit 0, everything is fine.  Otherwise it keeps a pointer
to struct file (with zero f_count!) around and has delayed
work do __fput() on it.

Better way to do it: use atomic_long_add_unless( , -1, 1)
instead of !atomic_long_dec_and_test().  IOW, decrement it
only if it's not the last reference, leave refcount alone
if it was.  And use normal fput() in delayed work.

I've made that atomic_long_add_unless call a new helper -
fput_atomic().  Drops a reference to file if it's safe to
do in atomic (i.e. if that's not the last one), tells if
it had been able to do that.  aio.c converted to it, __fput()
use is gone.  req->ki_file *always* contributes to refcount
now.  And __fput() became static.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

cpuidle_register_driver() sets cpuidle_curr_driver
cpuidle_unregister_driver() clears cpuidle_curr_driver

We should't expose cpuidle_curr_driver to
potential modification except via these interfaces.
So make it static and create cpuidle_get_driver() to observe it.
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a new driver to support the AB8500 Power Management chip, replacing
the current AB4500.  The new driver replaces the old one, instead of an
incremental modification, because this is a substantial overhaul
including:

 - Split of the driver into -core and -spi portions, to allow another
   interface layer to be added

 - Addition of interrupt support

 - Switch to MFD core API for handling subdevices

 - Simplification of the APIs to remove a redundant block parameter

 - Rename of the APIs and macros from ab4500_* to ab8500_*

 - Rename of the files from ab4500* to ab8500*

 - Change of the driver name from ab4500 to ab8500
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The interface for the AB3100 is changed to make way for the
ABX500 family of chips: AB3550, AB5500 and future ST-Ericsson
Analog Baseband chips. The register access functions are moved
out to a separate struct abx500_ops. In this way the interface
is moved from the implementation and the sub functionality drivers
can keep their interface intact when chip infrastructure and
communication mechanisms changes. We also define the AB3550
device IDs and the AB3550 platform data struct and convert
the catenated 32bit event to an array of 3 x 8bits.
Signed-off-by: NMattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The goal here is to make way for a more general interface for the
analog baseband chips ab3100 ab3550 ab550 and future chips.

This patch have been divided into two parts since both changing name
and content of a file is not recommended in git.
Signed-off-by: NMattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The TC35892 I/O Expander provides 24 GPIOs, a keypad controller, timers,
and a rotator wheel interface.  This patch adds the MFD core.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The charger interrupts on the WM831x are unconditionally a wake source
for the system. If the power driver is not able to monitor them (for
example, due to the IRQ line not having been wired up on the system)
then any charger interrupt will prevent the system suspending for any
meaningful amount of time since nothing will ack them.

Avoid this issue by manually acknowledging these interrupts when we
suspend the WM831x core device if they are masked. If software is
actually using the interrupts then they will be unmasked and this
change will have no effect.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add touch screen input driver for TPS6507x family of multi-function
chips.  Uses the TPS6507x MFD driver.  No interrupt support due to
testing limitations of current hardware.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

TPS6507x are multi function (PM, touchscreen) chipsets from TI.
This commit also changes the corresponding regulator driver from being
standalone to an MFD subdevice.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Other sub-drivers for the TPS6507x chip will need to use register
definition so move it out of the source file and into a header file.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Janz CMOD-IO PCI MODULbus carrier board is a PCI to MODULbus bridge,
which may host many different types of MODULbus daughterboards, including
CAN and GPIO controllers.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch fixes three section mismatches.

WARNING: drivers/mfd/88pm860x.o(.text+0x12): Section mismatch in
reference from the function pm860x_device_exit() to the function
.devexit.text:device_irq_exit()
The function pm860x_device_exit() references a function in an exit
section.
Often the function device_irq_exit() has valid usage outside the exit
section
and the fix is to remove the __devexit annotation of device_irq_exit.

WARNING: drivers/mfd/88pm860x.o(.text+0xb0): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8606_init()
The function pm860x_device_init() references
the function __devinit device_8606_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8606_init is wrong.

WARNING: drivers/mfd/88pm860x.o(.text+0xbe): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8607_init()
The function pm860x_device_init() references
the function __devinit device_8607_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8607_init is wrong.
Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds a new MFD driver for the RDC321x southbridge. This southbridge
is always present in the RDC321x System-on-a-Chip and provides access to some
GPIOs as well as a watchdog. Access to these two functions is done using the
southbridge PCI device configuration space.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When the user passes the kernel parameter acpi_enforce_resources=lax,
the ACPI resources are no longer protected, so a native driver can
make use of them. In that case, we do not want the asus_atk0110 to be
loaded. Unfortunately, this driver loads automatically due to its
MODULE_DEVICE_TABLE, so the user ends up with two drivers loaded for
the same device - this is bad.

So I suggest that we prevent the asus_atk0110 driver from loading if
acpi_enforce_resources=lax.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NLuca Tettamanti <kronos.it@gmail.com>
Cc: Len Brown <lenb@kernel.org>

Generic per-cpu counter has some memory overhead but it is negligible for
modern systems and embedded systems compile without quota support.  And code
reuse is a good thing. This patch should fix complain from preemptive kernels
which was introduced by dde95888.

[Jan Kara: Fixed patch to work on 32-bit archs as well]
Reported-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: NJan Kara <jack@suse.cz>

Introduce numa_mem_id(), based on generic percpu variable infrastructure
to track "nearest node with memory" for archs that support memoryless
nodes.

Define API in <linux/topology.h> when CONFIG_HAVE_MEMORYLESS_NODES
defined, else stubs.  Architectures will define HAVE_MEMORYLESS_NODES
if/when they support them.

Archs can override definitions of:

numa_mem_id() - returns node number of "local memory" node
set_numa_mem() - initialize [this cpus'] per cpu variable 'numa_mem'
cpu_to_mem()  - return numa_mem for specified cpu; may be used as lvalue

Generic initialization of 'numa_mem' occurs in __build_all_zonelists().
This will initialize the boot cpu at boot time, and all cpus on change of
numa_zonelist_order, or when node or memory hot-plug requires zonelist
rebuild.  Archs that support memoryless nodes will need to initialize
'numa_mem' for secondary cpus as they're brought on-line.

[akpm@linux-foundation.org: fix build]
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rework the generic version of the numa_node_id() function to use the new
generic percpu variable infrastructure.

Guard the new implementation with a new config option:

        CONFIG_USE_PERCPU_NUMA_NODE_ID.

Archs which support this new implemention will default this option to 'y'
when NUMA is configured.  This config option could be removed if/when all
archs switch over to the generic percpu implementation of numa_node_id().
Arch support involves:

  1) converting any existing per cpu variable implementations to use
     this implementation.  x86_64 is an instance of such an arch.
  2) archs that don't use a per cpu variable for numa_node_id() will
     need to initialize the new per cpu variable "numa_node" as cpus
     are brought on-line.  ia64 is an example.
  3) Defining USE_PERCPU_NUMA_NODE_ID in arch dependent Kconfig--e.g.,
     when NUMA is configured.  This is required because I have
     retained the old implementation by default to allow archs to
     be modified incrementally, as desired.

Subsequent patches will convert x86_64 and ia64 to use this implemenation.
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is an implementation of ->llseek useable for the rare special case
when userspace expects the seek to succeed but the (device) file is
actually not able to perform the seek.  In this case you use noop_llseek()
instead of falling back to the default implementation of ->llseek.
Signed-off-by: NJan Blunck <jblunck@suse.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are more architectures that don't support ARCH_HAS_SG_CHAIN than
those that support it.  This removes removes ARCH_HAS_SG_CHAIN in
asm-generic/scatterlist.h and lets arhictectures to define it.

It's clearer than defining ARCH_HAS_SG_CHAIN asm-generic/scatterlist.h and
undefing it in arhictectures that don't support it.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are only two ways to define sg_dma_len(); use sg->dma_length or
sg->length.  This patch introduces NEED_SG_DMA_LENGTH that enables
architectures to choose sg->dma_length or sg->length.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the first half of the attempt to use asm-generic/scatterlist.h
on every architecture.

There are only two ways to define scatterlist structure. So it's easy
to convert every architecture to use asm-generic/scatterlist.h.

This patch:

The trick for ISA_DMA_THRESHOLD in asm-generic/scatterlist.h doesn't work
for powerpc.  This lets architectures defin ISA_DMA_THRESHOLD.

Hopefully, we can remove ISA_DMA_THRESHOLD in the future; we can do better
to decide if the bouncing is necessary or not.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The aio compat code was not converting the struct iovecs from 32bit to
64bit pointers, causing either EINVAL to be returned from io_getevents, or
EFAULT as the result of the I/O.  This patch passes a compat flag to
io_submit to signal that pointer conversion is necessary for a given iocb
array.

A variant of this was tested by Michael Tokarev.  I have also updated the
libaio test harness to exercise this code path with good success.
Further, I grabbed a copy of ltp and ran the
testcases/kernel/syscall/readv and writev tests there (compiled with -m32
on my 64bit system).  All seems happy, but extra eyes on this would be
welcome.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix CONFIG_COMPAT=n build]
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Reported-by: NMichael Tokarev <mjt@tls.msk.ru>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: <stable@kernel.org>		[2.6.35.1]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It was reported in http://lkml.org/lkml/2010/3/8/309 that 32 bit readv and
writev AIO operations were not functioning properly.  It turns out that
the code to convert the 32bit io vectors to 64 bits was never written.
The results of that can be pretty bad, but in my testing, it mostly ended
up in generating EFAULT as we walked off the list of I/O vectors provided.

This patch set fixes the problem in my environment.  are greatly
appreciated.

This patch:

Factor out code that will be used by both compat_do_readv_writev and the
compat aio submission code paths.
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Reported-by: NMichael Tokarev <mjt@tls.msk.ru>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: <stable@kernel.org>		[2.6.35.1]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 2.6.5, it had been commented, 'for backwards compatibility,
removed in 2.7.x'. Since 2.6.31, it have been marked as __deprecated.

I think that we can remove the API safely now.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sync_single_range_for_cpu and sync_single_range_for_device hooks are
unnecessary because sync_single_for_cpu and sync_single_for_device can
be used instead.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

swiotlb_sync_single_range_for_cpu and swiotlb_sync_single_range_for_device
are unnecessary because swiotlb_sync_single_for_cpu and
swiotlb_sync_single_for_device can be used instead.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>