Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: NMiaohe Lin <linmiaohe@huawei.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Convert all the remaining 'fall through" code comments to the newer
'fallthrough;' keyword.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.

For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running.  So we now pass the
value of UTS_RELEASE to the firmware.  This adminq call is required per
the HAS document.  The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.

What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.

CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

Rename DPM_FLAG_NEVER_SKIP to DPM_FLAG_NO_DIRECT_COMPLETE which
matches its purpose more closely.

No functional impact.
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # for PCI parts
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>

If Rx flow control has been enabled (via autoneg or forced), packets
should not be dropped due to Rx descriptor ring exhaustion. Instead
pause frames should be used to apply back pressure. This only applies
if VFs are not in use.

Move SRRCTL setup to its own function for easy reuse and only set drop
enable bit if Rx flow control is not enabled.

Since v1: always enable dropping of packets if VFs in use.
Signed-off-by: NRobert Beckett <bob.beckett@collabora.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows incrementing the correct timeout statistic without any mess.
Down the road, devices can learn to reset just the specific queue.

The patch was generated with the following script:

use strict;
use warnings;

our $^I = '.bak';

my @work = (
["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"],
["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"],
["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"],
["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"],
["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"],
["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"],
["drivers/net/appletalk/cops.c", "cops_timeout"],
["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"],
["drivers/net/arcnet/arcnet.c", "arcnet_timeout"],
["drivers/net/arcnet/com20020.c", "arcnet_timeout"],
["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"],
["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"],
["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"],
["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"],
["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"],
["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"],
["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"],
["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"],
["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"],
["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"],
["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"],
["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"],
["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"],
["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"],
["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"],
["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"],
["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"],
["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"],
["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"],
["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"],
["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"],
["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"],
["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"],
["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"],
["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"],
["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"],
["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"],
["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"],
["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"],
["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"],
["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"],
["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"],
["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"],
["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"],
["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"],
["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"],
["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"],
["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"],
["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"],
["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"],
["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"],
["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"],
["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"],
["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"],
["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"],
["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"],
["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"],
["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"],
["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"],
["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"],
["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"],
["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"],
["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"],
["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"],
["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"],
["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"],
["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"],
["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"],
["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"],
["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"],
["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"],
["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"],
["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"],
["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"],
["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"],
["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"],
["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"],
["drivers/net/ethernet/jme.c", "jme_tx_timeout"],
["drivers/net/ethernet/korina.c", "korina_tx_timeout"],
["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"],
["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"],
["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"],
["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"],
["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"],
["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"],
["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"],
["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"],
["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"],
["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"],
["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"],
["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"],
["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"],
["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"],
["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"],
["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"],
["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"],
["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"],
["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"],
["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"],
["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"],
["drivers/net/ethernet/realtek/atp.c", "tx_timeout"],
["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"],
["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"],
["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"],
["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"],
["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"],
["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"],
["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"],
["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"],
["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"],
["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"],
["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"],
["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"],
["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"],
["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"],
["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"],
["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"],
["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"],
["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"],
["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"],
["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"],
["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"],
["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"],
["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"],
["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"],
["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"],
["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"],
["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"],
["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"],
["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"],
["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"],
["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"],
["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"],
["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"],
["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"],
["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"],
["drivers/net/slip/slip.c", "sl_tx_timeout"],
["include/linux/usb/usbnet.h", "usbnet_tx_timeout"],
["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"],
["drivers/net/usb/catc.c", "catc_tx_timeout"],
["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"],
["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"],
["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"],
["drivers/net/usb/hso.c", "hso_net_tx_timeout"],
["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"],
["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"],
["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"],
["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"],
["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"],
["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"],
["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"],
["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"],
["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"],
["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"],
["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"],
["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"],
["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"],
["drivers/net/wan/cosa.c", "cosa_net_timeout"],
["drivers/net/wan/farsync.c", "fst_tx_timeout"],
["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"],
["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"],
["drivers/net/wan/x25_asy.c", "x25_asy_timeout"],
["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"],
["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"],
["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"],
["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"],
["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"],
["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"],
["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"],
["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"],
["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"],
["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"],
["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"],
["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"],
["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"],
["drivers/tty/synclink.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"],
["net/atm/lec.c", "lec_tx_timeout"],
["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"]
);

for my $p (@work) {
	my @pair = @$p;
	my $file = $pair[0];
	my $func = $pair[1];
	print STDERR $file , ": ", $func,"\n";
	our @ARGV = ($file);
	while (<ARGV>) {
		if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) {
			print STDERR "found $1+$2 in $file\n";
		}
		if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) {
			print STDERR "$func found in $file\n";
		}
		print;
	}
}

where the list of files and functions is simply from:

git grep ndo_tx_timeout, with manual addition of headers
in the rare cases where the function is from a header,
then manually changing the few places which actually
call ndo_tx_timeout.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NHeiner Kallweit <hkallweit1@gmail.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NShannon Nelson <snelson@pensando.io>
Reviewed-by: NMartin Habets <mhabets@solarflare.com>

changes from v9:
	fixup a forward declaration
changes from v9:
	more leftovers from v3 change
changes from v8:
        fix up a missing direct call to timeout
        rebased on net-next
changes from v7:
	fixup leftovers from v3 change
changes from v6:
	fix typo in rtl driver
changes from v5:
	add missing files (allow any net device argument name)
changes from v4:
	add a missing driver header
changes from v3:
        change queue # to unsigned
Changes from v2:
        added headers
Changes from v1:
        Fix errors found by kbuild:
        generalize the pattern a bit, to pick up
        a couple of instances missed by the previous
        version.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.

Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.

Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.

This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Changing a network device MTU can be a fairly frequent operation, and
failure to change the MTU is reflected to user-space properly, both by
an appropriate message as well as by looking at whether the device's MTU
matches the configuration.

Demote the prints to debug prints by using netdev_dbg(), making all
Intel wired LAN drivers consistent, since they used a mixture of PCI
device and network device prints before.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.

If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.

The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: NManfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables the hardware feature "Media Auto Sense" also on the
i350. It works in the same way as on the 82850 devices. Hardware designs
using dual PHYs (fiber/copper) can enable this feature by setting the MAS
enable bits in the NVM_COMPAT register (0x03) in the EEPROM.
Signed-off-by: NManfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fatal read errors are worth warning about, unless of course the device
was just unplugged from the machine - something that's a rather normal
occurrence when the igb/igc adapter is located on a Thunderbolt dock. So,
let's only WARN() if there's a fatal read error while the device is
still present.

This fixes the following WARN splat that's been appearing whenever I
unplug my Caldigit TS3 Thunderbolt dock from my laptop:

  igb 0000:09:00.0 enp9s0: PCIe link lost
  ------------[ cut here ]------------
  igb: Failed to read reg 0x18!
  WARNING: CPU: 7 PID: 516 at
  drivers/net/ethernet/intel/igb/igb_main.c:756 igb_rd32+0x57/0x6a [igb]
  Modules linked in: igb dca thunderbolt fuse vfat fat elan_i2c mei_wdt
  mei_hdcp i915 wmi_bmof intel_wmi_thunderbolt iTCO_wdt
  iTCO_vendor_support x86_pkg_temp_thermal intel_powerclamp joydev
  coretemp crct10dif_pclmul crc32_pclmul i2c_algo_bit ghash_clmulni_intel
  intel_cstate drm_kms_helper intel_uncore syscopyarea sysfillrect
  sysimgblt fb_sys_fops intel_rapl_perf intel_xhci_usb_role_switch mei_me
  drm roles idma64 i2c_i801 ucsi_acpi typec_ucsi mei intel_lpss_pci
  processor_thermal_device typec intel_pch_thermal intel_soc_dts_iosf
  intel_lpss int3403_thermal thinkpad_acpi wmi int340x_thermal_zone
  ledtrig_audio int3400_thermal acpi_thermal_rel acpi_pad video
  pcc_cpufreq ip_tables serio_raw nvme nvme_core crc32c_intel uas
  usb_storage e1000e i2c_dev
  CPU: 7 PID: 516 Comm: kworker/u16:3 Not tainted 5.2.0-rc1Lyude-Test+ #14
  Hardware name: LENOVO 20L8S2N800/20L8S2N800, BIOS N22ET35W (1.12 ) 04/09/2018
  Workqueue: kacpi_hotplug acpi_hotplug_work_fn
  RIP: 0010:igb_rd32+0x57/0x6a [igb]
  Code: 87 b8 fc ff ff 48 c7 47 08 00 00 00 00 48 c7 c6 33 42 9b c0 4c 89
  c7 e8 47 45 cd dc 89 ee 48 c7 c7 43 42 9b c0 e8 c1 94 71 dc <0f> 0b eb
  08 8b 00 ff c0 75 b0 eb c8 44 89 e0 5d 41 5c c3 0f 1f 44
  RSP: 0018:ffffba5801cf7c48 EFLAGS: 00010286
  RAX: 0000000000000000 RBX: ffff9e7956608840 RCX: 0000000000000007
  RDX: 0000000000000000 RSI: ffffba5801cf7b24 RDI: ffff9e795e3d6a00
  RBP: 0000000000000018 R08: 000000009dec4a01 R09: ffffffff9e61018f
  R10: 0000000000000000 R11: ffffba5801cf7ae5 R12: 00000000ffffffff
  R13: ffff9e7956608840 R14: ffff9e795a6f10b0 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff9e795e3c0000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000564317bc4088 CR3: 000000010e00a006 CR4: 00000000003606e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   igb_release_hw_control+0x1a/0x30 [igb]
   igb_remove+0xc5/0x14b [igb]
   pci_device_remove+0x3b/0x93
   device_release_driver_internal+0xd7/0x17e
   pci_stop_bus_device+0x36/0x75
   pci_stop_bus_device+0x66/0x75
   pci_stop_bus_device+0x66/0x75
   pci_stop_and_remove_bus_device+0xf/0x19
   trim_stale_devices+0xc5/0x13a
   ? __pm_runtime_resume+0x6e/0x7b
   trim_stale_devices+0x103/0x13a
   ? __pm_runtime_resume+0x6e/0x7b
   trim_stale_devices+0x103/0x13a
   acpiphp_check_bridge+0xd8/0xf5
   acpiphp_hotplug_notify+0xf7/0x14b
   ? acpiphp_check_bridge+0xf5/0xf5
   acpi_device_hotplug+0x357/0x3b5
   acpi_hotplug_work_fn+0x1a/0x23
   process_one_work+0x1a7/0x296
   worker_thread+0x1a8/0x24c
   ? process_scheduled_works+0x2c/0x2c
   kthread+0xe9/0xee
   ? kthread_destroy_worker+0x41/0x41
   ret_from_fork+0x35/0x40
  ---[ end trace 252bf10352c63d22 ]---
Signed-off-by: NLyude Paul <lyude@redhat.com>
Fixes: 47e16692 ("igb/igc: warn when fatal read failure happens")
Acked-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Acked-by: NFeng Tang <feng.tang@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a series from Alexander Duyck this change adds UDP segmentation
offload support to the igb driver.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: NJosh Hunt <johunt@akamai.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And any other existing fields in this structure that refer to tc.
Specifically:

* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.

This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.

Remove tc_block_offload alias.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.

This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.

This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.

This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.

There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a packet which is utilizing the launchtime feature (via SO_TXTIME socket
option) also requests the hardware transmit timestamp, the hardware
timestamp is not delivered to the userspace. This is because the value in
skb->tstamp is mistaken as the software timestamp.

Applications, like ptp4l, request a hardware timestamp by setting the
SOF_TIMESTAMPING_TX_HARDWARE socket option. Whenever a new timestamp is
detected by the driver (this work is done in igb_ptp_tx_work() which calls
igb_ptp_tx_hwtstamps() in igb_ptp.c[1]), it will queue the timestamp in the
ERR_QUEUE for the userspace to read. When the userspace is ready, it will
issue a recvmsg() call to collect this timestamp.  The problem is in this
recvmsg() call. If the skb->tstamp is not cleared out, it will be
interpreted as a software timestamp and the hardware tx timestamp will not
be successfully sent to the userspace. Look at skb_is_swtx_tstamp() and the
callee function __sock_recv_timestamp() in net/socket.c for more details.
Signed-off-by: NVedang Patel <vedang.patel@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/ethernet/intel/igb/igb_main.c: In function ‘__igb_notify_dca’:
drivers/net/ethernet/intel/igb/igb_main.c:6694:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (dca_add_requester(dev) == 0) {
      ^
drivers/net/ethernet/intel/igb/igb_main.c:6701:2: note: here
  case DCA_PROVIDER_REMOVE:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: N"Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Failed in read the HW register is very serious for igb/igc driver,
as its hw_addr will be set to NULL and cause the adapter be seen as
"REMOVED".

We saw the error only a few times in the MTBF test for suspend/resume,
but can hardly get any useful info to debug.

Adding WARN() so that we can get the necessary information about
where and how it happens, and use it for root causing and fixing
this "PCIe link lost issue"

This affects igb, igc.
Signed-off-by: NFeng Tang <feng.tang@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Acked-by: NSasha Neftin <sasha.neftin@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.

Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NStanislav Fomichev <sdf@google.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:

	@mmiowb@
	@@
	- mmiowb();

and invoked as:

$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done

NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

There are two reasons for this.

First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.

Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().

We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.

Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.

skb->xmit_more is retained (but always 0) to not cause build breakage.

This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions.  Remaining drivers are converted in the next patches.
Suggested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.

Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.

Also move a couple of defines into the appropriate header file instead
of inline in the .c file.

Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend")
Signed-off-by: NArvind Sankar <niveditas98@gmail.com>
Reviewed-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

igb sets different WoL settings in system suspend callback and runtime
suspend callback.

The suspend direct complete optimization leaves igb in runtime suspended
state with wrong WoL setting during system suspend.

To fix this, we need to disable suspend direct complete optimization to
let igb always use suspend callback to set correct WoL during system
suspend.
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

According to comments in <linux/netdevice.h> we should return either >0
or -errno from ->ndo_set_features() if changing dev->features by itself.

Return 1 in such places to notify netdev_update_features() about applied
changes in dev->features.
Signed-off-by: NSerhey Popovych <serhe.popovych@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.

To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.

This introduces two new interfaces:

	bool flow_rule_match_key(rule, dissector_id)

that returns true if a given matching key is set on, and:

	flow_rule_match_XYZ(rule, &match);

To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With recent changes, need to bump the driver version to reflect the
changes.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.

In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 59361316.

Due to problems found in additional testing, this causes an illegal
context switch in the RCU read-side critical section.

CC: Dave Jones <davej@codemonkey.org.uk>
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.

Since commit 42eca230 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.

To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.

Fixes: 42eca230 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.

The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: NJesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.

The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
 on CPU0.

In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.

CC: Bernhard Kaindl  <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While reviewing code, I noticed that Eric Dumazet recommends that
drivers check the return code of napi_complete_done, and use that
to decide to enable interrupts or not when exiting poll.  One of
the Intel drivers was already fixed (ixgbe).

Upon looking at the Intel drivers as a whole, we are handling our
polling and NAPI exit in a few different ways based on whether we
have multiqueue and whether we have Tx cleanup included. Several
drivers had the bug of exiting NAPI with return 0, which appears
to mess up the accounting in the stack.

Consolidate all the NAPI routines to do best known way of exiting
and to just mostly look like each other.
1) check return code of napi_complete_done to control interrupt enable
2) return the actual amount of work done.
3) return budget immediately if need NAPI poll again

Tested the changes on e1000e with a high interrupt rate set, and
it shows about an 8% reduction in the CPU utilization when busy
polling because we aren't re-enabling interrupts when we're about
to be polled.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Reviewed-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The line continuation unintentionally adds whitespace so
instead use a coalesced format to remove the whitespace.

Miscellanea:

o Use a more typical style for ternaries and arguments
  for this logging message
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Acked-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Many of the Intel Ethernet drivers call skb_tx_timestamp() earlier than
necessary. Move the calls to this function to the latest point possible,
just prior to notifying hardware of the new Tx packet when we bump the
tail register.

This affects i40e, iavf, igb, igc, and ixgbe.

The e100, e1000, e1000e, fm10k, and ice drivers already call the
skb_tx_timestamp() function just prior to indicating the Tx packet to
hardware, so they do not need to be changed.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After bfcb79fc ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.

Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: NOza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>