The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.

On connecting the cable a message like this appears four times in the log:
 reset full speed USB device number 4 using uhci_hcd

That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.
Signed-off-by: NMark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Initialize USB PHY after every Link controller reset

Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

PHY drivers keep track of the current state of the hardware,
so don't change PHY settings under it.

Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref
Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are a large numbers of issues with ASM1051 devices in uas mode:

1) They do not support REPORT SUPPORTED OPERATION CODES

2) They use out of spec 8 byte status iu-s when they have no sense data,
   switching to normal 16 byte status iu-s when they do have sense data.

3) They hang / crash when combined with some disks, e.g. a Crucial M500 ssd.

4) They hang / crash when stressed (through e.g. sg_reset --bus) with disks
   with which then normally do work (once 1 & 2 are worked around).

Where as in BOT mode they appear to work fine, so the best way forward with
these devices is to just blacklist them for uas usage.

Unfortunately this is easier said then done. as older versions of the ASM1053
(which works fine) use the same usb-id as the ASM1051.

When connected over USB-3 the 2 can be told apart by the number of streams
they support. So this patch adds some less then pretty code to disable uas for
the ASM1051. When connected over USB-2, simply disable uas alltogether for
devices with the shared usb-id.

Cc: stable@vger.kernel.org # 3.16
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.

In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.

This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.

s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.

s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure the uwb_dev->bce entry is set before calling uwb_dev_add in
uwbd_dev_onair so that usermode will only see the device after it is
properly initialized.  This fixes a kernel panic that can occur if
usermode tries to access the IEs sysfs attribute of a UWB device before
the driver has had a chance to set the beacon cache entry.
Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NTaylor Braun-Jones <taylor.braun-jones@ge.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit d24d481b (usb-storage: Modify and export adjust_quirks so
that it can be used by uas) added the 'u' flag to the quirks module
parameter for usb-storage, but neglected to update the
documentation.  This patch adds the documentation.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>  # 3.15+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.

That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.

This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.

This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.

This patch should be backported to all kernels containing
commit 71c731a2.

Fixes: 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes <alexis.cortes@ti.com>
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes: 588b48ca ("usbip: move usbip userspace code out of staging")
which introduced build failure by not changing uapi/usbip.h include path
according to new location.
Signed-off-by: NPiotr Król <piotr.krol@3mdeb.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v3.17-rc4

These updates add back some PIDs that were lost in a recent revert and add a
couple of new ones. Included is also an update to how the sierra driver binds
its interfaces in order to avoid binding CDC interfaces.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add back some PIDs that were mistakingly remove when reverting commit
73228a05 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.

Fixes: 63a901c0 ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: NLei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.17-rc3

A new set of fixes which have been pending for a while. All patches
have been randconfig build-tested and boot tested where applicable.

The most important fixes are MUSB on AM335x learned how to transfer
ZLPs, and net2280 got a fix for reset IRQ handling.
Signed-of-by: NFelipe Balbi <balbi@ti.com>

Merge tag 'for-3.17-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus

Kishon writes:

for_3.17-rc

Fix regressions to runtime PM on OMAP and other minor fixes.

The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.

Fixes the following warning from the sparse checker:

	drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)

Fixes: 81d5dfe6 (usb: phy: tegra: Read UTMIP parameters from device tree)
Cc: stable@vger.kernel.org
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add compatible string for imx6sx-usbphy.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add imx6sx support
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Up to now, when endpoint addresses in descriptors were non-consecutive,
there were created redundant files, which could cause problems in kernel,
when user tried to read/write to them. It was result of fact that maximum
endpoint address was taken as total number of endpoints in function.

This patch adds endpoint descriptors counting and storing their addresses
in eps_addrmap to verify their cohesion in each speed.

Endpoint address map would be also useful for further features, just like
vitual endpoint address mapping.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the usb_pkt_pop(). If a gadget driver calls
usb_ep_dequeue(), this driver will call the usb_pkt_pop().
So, the usb_pkt_pop() should cancel the transaction.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the condition of is_done in usbhsf_dma_push_done().
This function will be called after a transmission finished by DMAC.
So, the function should check if the transmission packet is short packet
or not. Also the function should call try_run to send the zero packet
by the pio handler if the "*is_done" is not set. Otherwize, the
transaction will not finish if a gadget driver sets the "zero" flag
in a transmission.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch protects the mod->irq_bempsts and mod->irq_brdysts by
spin lock in the usbhs_status_get_each_irq() because other functions
will write them during spin lock. Otherwise, the driver will clears
the BRDYSTS and/or BEMPSTS wrongly, and then, the transaction will not
finish.
Also since the driver should use the INTSTS0 and BRDYSTS and BEMPSTS
as the same timing, the patch protects them.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some gadget drivers will call usb_ep_queue() more than once before
the first queue doesn't finish. However, this driver didn't handle
it correctly. So, this patch fixes the behavior of some
usbhs_pkt_handle using the "running" flag. Otherwise, the oops below
happens if we use g_ncm driver and when the "iperf -u -c host -b 200M"
is running.

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_ncm g_ncm libcomposite u_ether
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W      3.17.0-rc1-00008-g8b2be8a-dirty #20
task: c051c7e0 ti: c0512000 task.ti: c0512000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xa8/0x114
pc : [<00000000>]    lr : [<c0278fb4>]    psr: 60000193
sp : c0513ce8  ip : c0513c58  fp : c0513d24
r10: 00000001  r9 : 00000193  r8 : eebec4a0
r7 : eebec410  r6 : eebe0c6c  r5 : 00000000  r4 : ee4a2774
r3 : 00000000  r2 : ee251e00  r1 : c0513cf4  r0 : ee4a2774
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Clearly this was meant to be an include guard, but a trailing
underscore was missing. It has been this way since the file was
introduced in 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver").

Fixes: 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Without this patch, some hosts keep restarting indefinitely the target.

Fixes: ae8e530a (usb: gadget: net2280: Code Cleanup)
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

CPPI TX does not transmit ZLP for TX transfers which
- transfer size is multiple of EP packet size,
- and URB_ZERO_PACKET is set in urb->transfer_flags.

The fix is transmitting the ZLP using PIO mode after the CPPI TX is
done.

Validated using the following usbtest write case in MUSB host mode.

  # testusb -t1 -c1
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This VID:PID is used for some Direct IP devices behaving
identical to the already supported 0F3D:68AA devices.

Cc: <stable@vger.kernel.org>
Reported-by: NLars Melin <larsm17@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Sierra Wireless Direct IP devices using the 68A3 product ID
can be configured for modes including a CDC ECM class function.
The known example uses interface numbers 12 and 13 for the ECM
control and data interfaces respectively, consistent with CDC
MBIM function interface numbering on other Sierra devices.

It seems cleaner to restrict this driver to the ff/ff/ff
vendor specific interfaces rather than increasing the already
long interface number blacklist.  This should be more future
proof if Sierra adds more class functions using interface
numbers not yet in the blacklist.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add device id for NOVITUS Bono E thermal printer.
Reported-by: NEmanuel Koczwara <poczta@emanuelkoczwara.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add back some PIDs that were mistakingly remove when reverting commit
73228a05 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.

Fixes: 63a901c0 ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: NLei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>

Pull Xtensa updates from Chris Zankel:
 "Xtensa improvements for 3.17:
   - support highmem on cores with aliasing data cache.  Enable highmem
     on kc705 by default
   - simplify addition of new core variants (no need to modify Kconfig /
     Makefiles)
   - improve robustness of unaligned access handler and its interaction
     with window overflow/underflow exception handlers
   - deprecate atomic and spill registers syscalls
   - clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
     statements
   - wire up renameat2 syscall.

  Various fixes:
   - fix address checks in dma_{alloc,free}_coherent (runtime BUG)
   - fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
   - fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
     (runtime unrecoverable exception)
   - fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
     register clobbering)
   - fix kernel/user jump out of fast_unaligned (potential runtime
     unrecoverabl exception)
   - replace termios IOCTL code definitions with constants (userspace
     build breakage)"

* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
  xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
  xtensa: don't allow overflow/underflow on unaligned stack
  xtensa: fix a6 and a7 handling in fast_syscall_xtensa
  xtensa: allow single-stepping through unaligned load/store
  xtensa: move invalid unaligned instruction handler closer to its users
  xtensa: make fast_unaligned store restartable
  xtensa: add double exception fixup handler for fast_unaligned
  xtensa: fix kernel/user jump out of fast_unaligned
  xtensa: configure kc705 for highmem
  xtensa: support highmem in aliasing cache flushing code
  xtensa: support aliasing cache in kmap
  xtensa: support aliasing cache in k[un]map_atomic
  xtensa: implement clear_user_highpage and copy_user_highpage
  xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
  xtensa: allow fixmap and kmap span more than one page table
  xtensa: make fixmap region addressing grow with index
  xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
  xtensa: add renameat2 syscall
  xtensa: fix address checks in dma_{alloc,free}_coherent
  xtensa: replace IOCTL code definitions with constants
  ...

unicore32 builds fail with

  arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
  arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
  arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
  arch/unicore32/kernel/signal.c: In function ‘do_signal’:
  arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
  make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
  make: *** [arch/unicore32/kernel/signal.o] Error 2

Bisect points to commit 649671c9 ("unicore32: Use get_signal()
signal_setup_done()").

This code never even compiled.  Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up.  Compile
tested only.

Fixes: 649671c9 ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull ARM fixes from Russell King:
 "Various assorted fixes:

   - a couple of patches from Mark Rutland to resolve an errata with
     Cortex-A15 CPUs.
   - fix cpuidle for the CPU part ID changes in the last merge window
   - add support for a relocation which ARM binutils is generating in
     some circumstances"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
  ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
  ARM: 8128/1: abort: don't clear the exclusive monitors
  ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations