As the HNS3 driver doesn't update the MAC address directly in
function hns3_set_rx_mode() now, it can't know whether the
MAC table is full from __dev_uc_sync() and __dev_mc_sync(),
so it's senseless to handle the overflow promisc here.

This patch removes the handle of overflow promisc from function
hns3_set_rx_mode(), and updates the promisc mode in the service
task.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for dumping entries of UC and MC MAC list,
which help checking whether a MAC address being added into hardware
or not.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the HNS3 driver sync and unsync MAC address in function
hns3_set_rx_mode(). For PF, it adds and deletes MAC address directly
in the path of dev_set_rx_mode(). If failed, it won't retry until
next calling of hns3_set_rx_mode(). On the other hand, if request
add and remove a same address many times at a short interval, each
request must be done one by one, can't be merged. For VF, it sends
mailbox messages to PF to request adding or deleting MAC address in
the path of function hns3_set_rx_mode(), no matter the address is
configured success.

This patch refines it by recording the MAC address in function
hns3_set_rx_mode(), and updating MAC address in the service task.
If failed, it will retry by the next calling of periodical service
task. It also uses some state to mark the state of each MAC address
in the MAC list, which can help merge configure request for a same
address. With these changes, when global reset or IMP reset occurs,
we can restore the MAC table with the MAC list.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like the calculation elsewhere, replaces num_req_vfs with
num_alloc_vport in hclge_reset_umv_space().
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since hclge_set_umv_space() is only called by hclge_init_umv_space(),
so parameter 'is_alloc' is redundant.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, firmware helps manage the unicast MAC VLAN table
space for each PF. PF just needs to tell firmware its wanted
space when initializing, and unnecessary to free it when
un-intializing. So this patch removes the umv space free handle,
and removes the forward statement of hclge_set_umv_space()
by defining hclge_init_umv_space() after it.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes coccicheck warning:

drivers/net/ethernet/aquantia/atlantic/aq_macsec.c:404:2-3: Unneeded semicolon
drivers/net/ethernet/aquantia/atlantic/aq_macsec.c:420:2-3: Unneeded semicolon
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZheng Bin <zhengbin13@huawei.com>
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes coccicheck warning:

drivers/net/ethernet/mellanox/mlxfw/mlxfw_fsm.c:79:2-3: Unneeded semicolon
drivers/net/ethernet/mellanox/mlxfw/mlxfw_fsm.c:162:2-3: Unneeded semicolon
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZheng Bin <zhengbin13@huawei.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is designed to drop Rx packets and reclaim the buffers
when an allocation fails, and the network interface needs to safely
handle this packet loss. Therefore, an allocation failure of Rx
SKBs is relatively benign.

However, the output of the warning message occurs with a high
scheduling priority that can cause excessive jitter/latency for
other high priority processing.

This commit suppresses the warning messages to prevent scheduling
problems while retaining the failure count in the statistics of
the network interface.
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is designed to drop Rx packets and reclaim the buffers
when an allocation fails, and the network interface needs to safely
handle this packet loss. Therefore, an allocation failure of Rx
SKBs is relatively benign.

However, the output of the warning message occurs with a high
scheduling priority that can cause excessive jitter/latency for
other high priority processing.

This commit suppresses the warning messages to prevent scheduling
problems while retaining the failure count in the statistics of
the network interface.
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers ndo_setup_tc call should return -EOPNOTSUPP, when it cannot
support the qdisc type. Other return values will result in failing the
qdisc setup.  This lead to qdisc noop getting assigned, which will
drop all TX packets on the interface.

Fixes: ab1e6de2 ("dpaa2-eth: Add mqprio support")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Tested-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to commit e99f8e7f ("mlxsw: Replace zero-length
array with flexible-array member"), use a flexible-array member to get a
compiler warning in case the flexible array does not occur last in the
structure.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'refcount_t' is very useful for catching over/under flows. Convert the
SPAN agent objects to use it instead of 'int' for their reference count.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To the best of my knowledge, these debug prints were never used. Remove
them.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more meaningful name for parms() function.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use early return to avoid unnecessary nesting.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The change to track net_device_stats per ring to better support SMP
missed updating the rx_dropped member.

The ndo_get_stats method is also needed to combine the results for
ethtool statistics (-S) before filling in the ethtool structure.

Fixes: 37a30b43 ("net: bcmgenet: Track per TX/RX rings statistics")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Evidently, at some point in the pre-githistorious past,
drivers/net/ethernet/sgi/meth.h somehow contained some code from the
"snull" driver from the Linux Device Drivers book.  A comment crediting
that source, asserting copyright ownership by the LDD authors, and imposing
the LDD2 license terms was duly added to the file.

Any code that may have been derived from snull is long gone, and the
distribution terms are not GPL-compatible.  Since the copyright claim is
not based in fact (if it ever was), simply remove it and the distribution
terms as well.
Reported-by: NJan Kiszka <jan.kiszka@siemens.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Kate Stewart <kstewart@linuxfoundation.org>
CC: "Fendt, Oliver" <oliver.fendt@siemens.com>
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following sparse warning:

drivers/net/ethernet/qlogic/qed/qed_ll2.c:2334:20: warning: symbol 'll2_cbs'
was not declared. Should it be static?
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZou Wei <zou_wei@huawei.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function ixp4xx_eth_probe() does not perform sufficient error
checking after executing devm_ioremap_resource(), which can result
in crashes if a critical error path is encountered.

Fixes: f458ac47 ("ARM/net: ixp4xx: Pass ethernet physical base as resource")
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NTang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPSW misc IRQ need be enabled for CPTS event_pend IRQs processing. This
patch adds corresponding support to CPSW driver.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hence CPTS IRQ support is in place the W_TS_PUSH events can be added.
PWM capable DmTimers can be used to generete input signals for CPTS on TI
AM335x/AM437x/DRA7 SoCs to be timestamped:
AM335x/AM437x: timer4 - timer7
DRA7/AM57xx: timer13 - timer16
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add CPTS IRQ support, but do not enable it. By default, the CPTS driver
will continue working using polling mode which is required for CPTS to
continue working on platforms other than CPSW, like Keystone 2.

The CPTS IRQ support is required to enable support for HW_TS_PUSH events.
The CPSW CPTS IRQ and HW_TS_PUSH events support will be enabled in follow
up patches.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now spinlock is used to synchronize everything which is not required. Add
mutex and use to sync access to PTP interface and PTP worker and use
spinlock only to sync FIFO/events processing.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now the tx timestamp processing happens from different contexts - softirq
and thread/PTP worker. Enabling IRQ will add one more hard_irq context.
This makes over all defered TX timestamp processing and locking
overcomplicated. Move tx timestamp processing to PTP worker always instead.

napi_rx->cpts_tx_timestamp
 if ptp_packet then
    push to txq
    ptp_schedule_worker()

do_aux_work->cpts_overflow_check
 cpts_process_events()
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now the CPTS driver performs packet (skb) parsing every time when it needs
to match packet to CPTS event (including ptp_classify_raw() calls).

This patch optimizes matching process by parsing packet only once upon
arrival and stores PTP specific data in skb->cb using the same fromat as in
CPTS HW event. As result, all future matching reduces to comparing two u32
values.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPTS HW latches and saves CPTS counter value in CPTS fifo immediately
after writing to CPSW_CPTS_PUSH.TS_PUSH (bit 0), so the total time that the
driver needs to read the CPTS timestamp is the time required CPSW_CPTS_PUSH
write to actually reach HW.

Hence switch CPTS driver to implement new .gettimex64() callback for more
precise measurement of the offset between a PHC and the system clock which
is measured as time between
  write(CPSW_CPTS_PUSH)
  read(CPSW_CPTS_PUSH)
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now CPTS driver .adjfreq() generates request to read CPTS current time
(CPTS_EV_PUSH) with intention to process all pending event using previous
frequency adjustment values before switching to the new ones. So
CPTS_EV_PUSH works as a marker to switch to the new frequency adjustment
values. Current code assumes that all job is done in .adjfreq(), but after
enabling IRQ this will not be true any more.

Hence save new frequency adjustment values (mult) and perform actual freq
adjustment in cpts_fifo_read() immediately after CPTS_EV_PUSH is received.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now CPTS HW time reading code is implemented in timecounter->cyclecounter
.read() callback and performs following operations:
timecounter_read() ->cc.read() -> cpts_systim_read()
 - request current CPTS HW time CPTS_TS_PUSH.TS_PUSH = 1
 - poll CPTS FIFO for CPTS_EV_PUSH event with current HW timestamp

This approach need to be changed for the future switch to PTP PHC
.gettimex64() callback, which require to separate requesting current CPTS
HW time and processing CPTS FIFO. And for the follow up patch, which
improves .adjfreq() implementation.

This patch moves code accessing CPTS HW out of timecounter code as
following:
- convert HW timestamp of every CPTS event to PTP time (us) and store it as
part struct cpts_event;
- add CPTS context field to store current CPTS HW time (counter) value and
update it on CPTS_EV_PUSH reception;
- move code accessing CPTS HW out of timecounter code and use current CPTS
HW time (counter) from CPTS context instead;
- ensure timecounter->cycle_last is updated on CPTS_EV_PUSH reception.

After this change CPTS timecounter will only perform timekeeper role
without actually accessing CPTS HW.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dev_yy() API instead of pr_yy() for log outputs.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to benefit from the new napi_defer_hard_irqs feature,
we need to use napi_complete_done() variant in this driver.

RX path is already using it, this patch implements TX completion side.

mlx4_en_process_tx_cq() now returns the amount of retired packets,
instead of a boolean, so that mlx4_en_poll_tx_cq() can pass
this value to napi_complete_done().
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the absence of MC1, the size calculation function
cudbg_mem_region_size() was returing wrong MC size and
resulted in adapter crash. This patch adds new argument
to cudbg_mem_region_size() which will have actual size
and returns error to caller in the absence of MC1.

Fixes: a1c69520 ("cxgb4: collect MC memory dump")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error recovery is handled by management firmware (MFW) with the help of
qed/qede drivers. Upon detecting the errors, driver informs MFW about this
event which in turn starts a recovery process. MFW sends ERROR_RECOVERY
notification to the driver which performs the required cleanup/recovery
from the driver side.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Acked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch enables the device to send error messages to root port when
an error is detected.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlxsw_sp_acl_rulei_create() function is supposed to return an error
pointer from mlxsw_afa_block_create().  The problem is that these
functions both return NULL instead of error pointers.  Half the callers
expect NULL and half expect error pointers so it could lead to a NULL
dereference on failure.

This patch changes both of them to return error pointers and changes all
the callers which checked for NULL to check for IS_ERR() instead.

Fixes: 4cda7d8d ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take advantage of the bulk enqueue feature in .ndo_xdp_xmit.
We cannot use the XDP_XMIT_FLUSH since the architecture is not capable
to store all the frames dequeued in a NAPI cycle so we instead are
enqueueing all the frames received in a ndo_xdp_xmit call right away.

After setting up all FDs for the xdp_frames received, enqueue multiple
frames at a time until all are sent or the maximum number of retries is
hit.
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having a function that both creates a frame descriptor from
an xdp_frame and enqueues it, split this into two stages.
Add the dpaa2_eth_xdp_create_fd that just transforms an xdp_frame into a
FD while the actual enqueue callback is called directly from the ndo for
each frame.
This is particulary useful in conjunction with bulk enqueue.
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the dpaa2-eth driver to use the bulk enqueue function introduced
with the change to QBMAN ring mode. At the moment, no functional changes
are made but rather the driver just transitions to the new interface
while still enqueuing just one frame at a time.
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The enqueue dpaa2-eth callback now returns the number of successfully
enqueued frames. This is a preliminary patch necessary for adding
support for bulk ring mode enqueue.
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For dwmac4, enable VLAN promiscuity when MAC controller is requested to
enter promiscuous mode.
Signed-off-by: NChuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NTan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: NWong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>