This patch replaces all occurences of the form
intel_uncore_write(reg, intel_uncore_read(reg) OP val)
with intel_uncore_rmw.
Signed-off-by: NAndrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAndi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: NAndi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221019143818.244339-2-andrzej.hajda@intel.com

This patch replaces all occurences of the form
intel_uncore_write(reg, intel_uncore_read(reg) OP val)
with intel_uncore_rmw.
Signed-off-by: NAndrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAndi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: NAndi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221019143818.244339-1-andrzej.hajda@intel.com

A misplaced closing parenthesis caused the groupid/instanceid values to
be considered part of the ternary operator's condition instead of being
OR'd into the resulting value.

Fixes: f32898c9 ("drm/i915/xelpg: Add multicast steering")
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NArun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221019222437.3035182-1-matthew.d.roper@intel.com

Since a7c01fa9 ("signal: break out of wait loops on kthread_stop()")
kthread_stop() started asserting a pending signal which wreaks havoc with
a few of our selftests. Mainly because they are not fully expecting to
handle signals, but also cutting the intended test runtimes short due
signal_pending() now returning true (via __igt_timeout), which therefore
breaks both the patterns of:

  kthread_run()
  ..sleep for igt_timeout_ms to allow test to exercise stuff..
  kthread_stop()

And check for errors recorded in the thread.

And also:

    Main thread  |   Test thread
  ---------------+------------------------------
  kthread_run()  |
  kthread_stop() |  do stuff until __igt_timeout
		 |  -- exits early due signal --

Where this kthread_stop() was assume would have a "join" semantics, which
it would have had if not the new signal assertion issue.

To recap, threads are now likely to catch a previously impossible
ERESTARTSYS or EINTR, marking the test as failed, or have a pointlessly
short run time.

To work around this start using kthread_work(er) API which provides
an explicit way of waiting for threads to exit. And for cases where
parent controls the test duration we add explicit signaling which threads
will now use instead of relying on kthread_should_stop().
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020130841.3845791-1-tvrtko.ursulin@linux.intel.com

The fact that LMEMBAR is BAR2 should be of no real interest
to anyone. So use the name of the BAR rather than its index.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221005154159.18750-3-ville.syrjala@linux.intel.comAcked-by: NMatthew Auld <matthew.auld@intel.com>

We use all kinds of weird names for our base address registers.
Take the names from the spec and stick to them to avoid confusing
everyone.

The only exceptions are IOBAR and LMEMBAR since naming them
IOBAR_BAR and LMEMBAR_BAR looks too funny, and yet I think
that adding the _BAR to GTTMMADR & co. (which don't have one
in the spec name) does make it more clear what they are.
And IOBAR vs. GTTMMADR_BAR also looks a bit too inconsistent
for my taste.

v2: Fix gvt build
v3: Add GEN2_IO_BAR for completeness
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221005195646.17201-1-ville.syrjala@linux.intel.comAcked-by: NMatthew Auld <matthew.auld@intel.com>

We have the same code to determine the MMIO BAR in
two places. Collect it to a single place.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221005154159.18750-1-ville.syrjala@linux.intel.comReviewed-by: NMatthew Auld <matthew.auld@intel.com>

Currently i915_ttm_to_gem() returns NULL for ttm ghost
object which makes it unclear when we should add a NULL
check for a caller of i915_ttm_to_gem() as ttm ghost
objects are expected behaviour for certain cases.

Create a separate function to detect ttm ghost object and
use that in places where we expect a ghost obj from ttm.
Signed-off-by: NNirmoy Das <nirmoy.das@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014131427.21102-1-nirmoy.das@intel.com

The bspec was just updated with a correction to the forcewake domain
required when accessing registers in the CCS engine ranges (0x1a000 -
0x1ffff and 0x26000 - 0x27fff) on PVC; these ranges require a wake on
the RENDER domain, not the GT domain.

Bspec: 67609
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NHarish Chegondi <harish.chegondi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014233004.1053678-1-matthew.d.roper@intel.com

We're observing sporadic HuC delayed load timeouts in CI, due to mei_pxp
binding completing later than we expected. HuC is still loaded when the
bind occurs, but in the meantime i915 has started allowing submission to
the VCS engines even if HuC is not there.
In most of the cases I've observed, the timeout was due to the
init/resume of another driver between i915 and mei hitting errors and
thus adding an extra delay, but HuC was still loaded before userspace
could submit, because the whole resume process time was increased by the
delays.

Given that there is no upper bound to the delay that can be introduced
by other drivers, I've reached the following compromise with the media
team:

1) i915 is going to bump the timeout to 5s, to reduce the probability
of reaching it. We still expect HuC to be loaded before userspace
starts submitting, so increasing the timeout should have no impact on
normal operations, but in case something weird happens we don't want to
stall video submissions for too long.

2) The media driver will cope with the failing submissions that manage
to go through between i915 init/resume complete and HuC loading, if any
ever happen. This could cause a small corruption of video playback
immediately after a resume (we should be safe on boot because the media
driver polls the HUC_STATUS ioctl before starting submissions).

Since we're accepting the timeout as a valid outcome, I'm also reducing
the print verbosity from error to notice.

v2: use separate prints for MEI GSC and MEI PXP init timeouts (John)
v3: add MISSING_CASE to the if-else chain (John)

References: https://gitlab.freedesktop.org/drm/intel/-/issues/7033
Fixes: 27536e03 ("drm/i915/huc: track delayed HuC load with a fence")
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tony Ye <tony.ye@intel.com>
Cc: John Harrison <john.c.harrison@intel.com>
Reviewed-by: NJohn Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013203245.1801788-1-daniele.ceraolospurio@intel.com

MTL's media IP (Xe_LPM+) only has a single type of steering ("OAADDRM")
which selects between media slice 0 and media slice 1.  We'll always
steer to media slice 0 unless it is fused off (which is the case when
VD0, VE0, and SFC0 are all reported as unavailable).

Bspec: 67789
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-15-matthew.d.roper@intel.com

MTL's graphics IP (Xe_LPG) once again changes the multicast register
types and steering details.  Key changes from past platforms:
 * The number of instances of some MCR types (NODE, OAAL2, and GAM) vary
   according to the MTL subplatform and cannot be read from fuse
   registers.  However steering to instance #0 will always provided a
   non-terminated value, so we can lump these all into a single
   "instance0" table.
 * The MCR steering register (and its bitfields) has changed.

Unlike past platforms, we will be explicitly steering all types of MCR
accesses, including those for "SLICE" and "DSS" ranges; we no longer
rely on implicit steering.  On previous platforms, various
hardware/firmware agents that needed to access registers typically had
their own steering control registers, allowing them to perform multicast
steering without clobbering the CPU/kernel steering.  Starting with MTL,
more of these agents now share a single steering register (0xFD4) and it
is no longer safe for us to assume that the value will remain unchanged
from how we initialized it during startup.  There is also a slight
chance of race conditions between the driver and a hardware/firmware
agent, so the hardware provides a semaphore register that can be used to
coordinate access to the steering register.  Support for the semaphore
register will be introduced in a future patch.

v2:
 - Use Xe_LPG terminology instead of "MTL 3D" since it's the IP version
   we're matching on now rather than the platform.
 - Don't combine l3bank and mslice masks into a union.  It's not related
   to the other changes here and we might still need both of them on
   some future platform.
 - Separate debug dumping of steering settings to a separate helper
   function.  (Tvrtko)
 - Update debug dumping to include DSS ranges (and future-proof it so
   that any new ranges added on future platforms will also be dumped).
 - Restore MULTICAST bit at the end of rw_with_mcr_steering_fw() if we
   cleared it.  Also force the MULTICAST bit to true at the beginning of
   multicast writes just to be safe.  (Bala)

Bspec: 67788, 67112
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-14-matthew.d.roper@intel.com

Rather than treating multicast registers as 'i915_reg_t' let's define
them as a completely new type.  This will allow the compiler to help us
make sure we're using multicast-aware functions to operate on multicast
registers.

This plan does break down a bit in places where we're just maintaining
heterogeneous lists of registers (e.g., various MMIO whitelists used by
perf, GVT, etc.) rather than performing reads/writes.  We only really
care about the offset in those cases, so for now we can "cast" the
registers as non-MCR, leaving us with a list of i915_reg_t's, but we may
want to look for better ways to store mixed collections of i915_reg_t
and i915_mcr_reg_t in the future.

v2:
 - Add TLB invalidation registers
v3:
 - Make type checking of i915_mmio_reg_offset() stricter.  It will
   accept either i915_reg_t or i915_mcr_reg_t, but will now raise a
   compile error if any other type is passed, even if that type contains
   a 'reg' field.  (Jani)
 - Drop a ton of GVT changes; allowing i915_mmio_reg_offset() to take
   either an i915_reg_t or an i915_mcr_reg_t means that the huge lists
   of MMIO_D*() macros used in GVT will continue to work without
   modification.  We need only make changes to structures that have an
   explicit i915_reg_t in them now.

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-13-matthew.d.roper@intel.com

Let's be more explicit about which of our workarounds are updating MCR
registers.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-12-matthew.d.roper@intel.com

MCR registers can be placed on the GuC's save/restore list, but at the
moment they are always handled in a multicast manner (i.e., the GuC
reads one instance to save the value and then does a multicast write to
restore that single value to all instances).  In the future the GuC will
probably give us an alternate interface to do unicast per-instance
save/restore operations, so we should be very clear about which
registers on the list are MCR registers (and in the future which
save/restore behavior we want for them).
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-11-matthew.d.roper@intel.com

Rather than relying on the implicit behavior of intel_uncore_*()
functions, let's always use the intel_gt_mcr_*() functions to operate on
multicast/replicated registers.

v2:
 - Add TLB invalidation registers

v3:
 - Switch more uncore operations in mmio_invalidate_full() to MCR
   operations for Xe_HP.  (Bala)

Cc: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-10-matthew.d.roper@intel.com

Rather than using the same _MMIO() macro to define MCR registers as
singleton registers, let's use a new MCR_REG() macro to make it clear
that these registers are special and should be handled accordingly.  For
now MCR_REG() will still generate an i915_reg_t with the given offset,
but we'll change that in future patches.

Bspec: 66673, 66696, 66534, 67609
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-9-matthew.d.roper@intel.com

Xe_HP has some MCR registers that need to be polled for completion of
operations like TLB invalidation.  Those registers are in the GAM range,
which rolls up the status from each unit into the 'primary' instance's
value.  This makes it useful to have a dedicated 'wait for register'
function that handles this on MCR registers, similar to the
__intel_wait_for_register_fw() function we already have for regular
registers.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-8-matthew.d.roper@intel.com

On Xe_HP the fault registers are now in a multicast register range.
However as part of the GAM these registers follow special rules and we
need only read from the "primary" GAM's instance to get the information
we need.  So a single intel_gt_mcr_read_any() (which will automatically
steer to the primary GAM) is sufficient; we don't need to loop over each
instance of the MCR register.

v2:
 - Update more instances of fault registers.  (Bala)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-7-matthew.d.roper@intel.com

There are cases where we wish to read from any non-terminated MCR
register instance (or the primary instance in the case of GAM ranges),
clear/set some bits, and then write the value back out to the register
in a multicast manner.  Adding a "multicast RMW" will avoid the need to
open-code this.

v2:
 - Return a u32 to align with the recent change to intel_uncore_rmw.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-6-matthew.d.roper@intel.com

We have a few registers that have existed for several hardware
generations, but are only used by the driver on Xe_HP and beyond.  In
cases where the Xe_HP version of the register is now replicated and uses
multicast behavior, but earlier generations were singleton, let's change
the register prefix to "XEHP_" to help clarify that we're using the
newer multicast form of the register.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-5-matthew.d.roper@intel.com

Let's drop a few register definitions that are unused anywhere in the
driver today.  Since the referenced offsets are part of what is now
considered a multicast register region, the current definitions would
not be correct for use on any future platform.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-4-matthew.d.roper@intel.com

Starting in Xe_HP, several registers our driver works with have been
converted from singleton registers into replicated registers with
multicast behavior.  Although the registers are still located at the
same MMIO offsets as on previous platforms, let's duplicate the register
definitions in preparation for upcoming patches that will handle
multicast registers in a special manner.

The registers that are now replicated on Xe_HP are:
 * PAT_INDEX (mslice replication)
 * FF_MODE2 (gslice replication)
 * COMMON_SLICE_CHICKEN3 (gslice replication)
 * SLICE_COMMON_ECO_CHICKEN1 (gslice replication)
 * SLICE_UNIT_LEVEL_CLKGATE (gslice replication)
 * LNCFCMOCS (lncf replication)

Note that there are a couple places in selftest_mocs.c where the
gen9 version of LNCFCMOCS is still used without regards for which
platform we're on.  Those cases are just doing an offset lookup and not
issuing any CPU reads/writes of the register, so the potentially
multicast nature of the register doesn't come into play.

v2:
 - Add commit message note about the unconditional GEN9_LNCFCMOCS usage
   in selftest_mocs.  (Bala)
 - Include some additional TLB registers.

Bspec: 66534
Cc: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-3-matthew.d.roper@intel.com

Gen8 was the first time our hardware had multicast registers (or at
least the first time the multicast nature was exposed and MMIO accesses
could be steered).  There are some registers that transitioned from
singleton behavior to multicast during the gen7 -> gen8 transition;
let's duplicate the register definitions for those registers in
preparation for upcoming patches that will handle MCR registers in a
special manner.

The registers adjusted are:
 * MISCCPCTL
 * SAMPLER_INSTDONE
 * ROW_INSTDONE
 * ROW_CHICKEN2
 * HALF_SLICE_CHICKEN1
 * HALF_SLICE_CHICKEN3

v2:
 - Use the gen8 version of HALF_SLICE_CHICKEN3 in GVT's gen9 engine MMIO
   list.  (Bala)
 - Update to the gen8 version of MISCCPCTL in a couple new workarounds
   that were recently added for DG2/PVC.  (Bala)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Reviewed-by: NBalasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014230239.1023689-2-matthew.d.roper@intel.com

Extend hwmon power/energy for XEHPSDV especially per gt level energy
usage.

v2: Update to latest HWMON spec (Ashutosh)
v3: Fix review comments (Ashutosh)
v4: Fix review comments (Anshuman)
v5: s/hwmon_device_register_with_info/
    devm_hwmon_device_register_with_info/ (Ashutosh)
v6: Change contact to intel-gfx (Rodrigo)
    GEN12_RPSTAT1 is available for all Gen12+ (Andi)
Signed-off-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NDale B Stimson <dale.b.stimson@intel.com>
Signed-off-by: NBadal Nilawar <badal.nilawar@intel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: NAndi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013154526.2105579-8-ashutosh.dixit@intel.com

Expose power1_max_interval, that is the tau corresponding to PL1, as a
custom hwmon attribute. Some bit manipulation is needed because of the
format of PKG_PWR_LIM_1_TIME in
GT0_PACKAGE_RAPL_LIMIT register (1.x * power(2,y)).

v2: Update date and kernel version in Documentation (Badal)
v3: Cleaned up hwm_power1_max_interval_store() (Badal)
v4:
  - Fixed review comments (Anshuman)
  - In hwm_power1_max_interval_store() get PKG_MAX_WIN from
    pkg_power_sku when it is valid (Ashutosh)
  - KernelVersion: 6.2, Date: February 2023 in doc (Tvrtko)
v5: On some of the DGFX setups it is seen that although pkg_power_sku
    is valid the field PKG_WIN_MAX is not populated. So it is
    decided to stick to default value of PKG_WIN_MAX (Ashutosh)
v6: Change contact to intel-gfx (Rodrigo)
    Fixed variable types in hwm_power1_max_interval_store (Andi)
    Documented PKG_MAX_WIN_DEFAULT (Andi)
    Removed else in hwm_attributes_visible (Andi)
Signed-off-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NBadal Nilawar <badal.nilawar@intel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013154526.2105579-7-ashutosh.dixit@intel.com

Expose the card reactive critical (I1) power. I1 is exposed as
power1_crit in microwatts (typically for client products) or as
curr1_crit in milliamperes (typically for server).

v2: Add curr1_crit functionality (Ashutosh)
v3: Use HWMON_CHANNEL_INFO to define power1_crit, curr1_crit (Badal)
v4: Use hwm_ prefix for static functions (Ashutosh)
v5: KernelVersion: 6.2, Date: February 2023 in doc (Tvrtko)
v6: Change contact to intel-gfx (Rodrigo)

Cc: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Signed-off-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NBadal Nilawar <badal.nilawar@intel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013154526.2105579-6-ashutosh.dixit@intel.com

Use i915 HWMON to display device level energy input.

v2: Updated the date and kernel version in feature description
v3:
  - Cleaned up hwm_energy function and removed unused function
    i915_hwmon_energy_status_get (Ashutosh)
v4: KernelVersion: 6.2, Date: February 2023 in doc (Tvrtko)
v5: Change contact to intel-gfx (Rodrigo)
    Change return type of hwm_energy to void (Andi)
Signed-off-by: NDale B Stimson <dale.b.stimson@intel.com>
Signed-off-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NRiana Tauro <riana.tauro@intel.com>
Signed-off-by: NBadal Nilawar <badal.nilawar@intel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013154526.2105579-5-ashutosh.dixit@intel.com

Use i915 HWMON to display/modify dGfx power PL1 limit and TDP setting.

v2:
  - Fix review comments (Ashutosh)
  - Do not restore power1_max upon module unload/load sequence
    because on production systems modules are always loaded
    and not unloaded/reloaded (Ashutosh)
  - Fix review comments (Jani)
  - Remove endianness conversion (Ashutosh)
v3: Add power1_rated_max (Ashutosh)
v4:
  - Use macro HWMON_CHANNEL_INFO to define power channel (Guenter)
  - Update the date and kernel version in Documentation (Badal)
v5: Use hwm_ prefix for static functions (Ashutosh)
v6: Fix review comments (Ashutosh)
v7:
  - Define PCU_PACKAGE_POWER_SKU for DG1,DG2 and move
    PKG_PKG_TDP to intel_mchbar_regs.h (Anshuman)
  - KernelVersion: 6.2, Date: February 2023 in doc (Tvrtko)
v8: Change contact to intel-gfx (Rodrigo)
    Minor change to val_sku_unit init (Andi)

Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: NDale B Stimson <dale.b.stimson@intel.com>
Signed-off-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NRiana Tauro <riana.tauro@intel.com>
Signed-off-by: NBadal Nilawar <badal.nilawar@intel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: NAndi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013154526.2105579-4-ashutosh.dixit@intel.com

Use i915 HWMON subsystem to display current input voltage.

v2:
  - Updated date and kernel version in feature description
  - Fixed review comments (Ashutosh)
v3: Use macro HWMON_CHANNEL_INFO to define hwmon channel (Guenter)
v4:
  - Fixed review comments (Ashutosh)
  - Use hwm_ prefix for static functions (Ashutosh)
v5: Added unit of voltage as millivolts (Ashutosh)
v6: KernelVersion: 6.2, Date: February 2023 in doc (Tvrtko)
v7: Change contact to intel-gfx (Rodrigo)
    GEN12_RPSTAT1 is available for all Gen12+ (Andi)
    Added Documentation/ABI/testing/sysfs-driver-intel-i915-hwmon
    to MAINTAINERS

Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NRiana Tauro <riana.tauro@intel.com>
Signed-off-by: NBadal Nilawar <badal.nilawar@intel.com>
Signed-off-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013154526.2105579-3-ashutosh.dixit@intel.com

The i915 HWMON module will be used to expose voltage, power and energy
values for dGfx. Here we set up i915 hwmon infrastructure including i915
hwmon registration, basic data structures and functions.

v2:
  - Create HWMON infra patch (Ashutosh)
  - Fixed review comments (Jani)
  - Remove "select HWMON" from i915/Kconfig (Jani)
v3: Use hwm_ prefix for static functions (Ashutosh)
v4: s/#ifdef CONFIG_HWMON/#if IS_REACHABLE(CONFIG_HWMON)/ since the former
    doesn't work if hwmon is compiled as a module (Guenter)
v5: Fixed review comments (Jani)
v6: s/kzalloc/devm_kzalloc/ (Andi)
v7: s/hwmon_device_register_with_info/
      devm_hwmon_device_register_with_info/ (Ashutosh)

Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: NDale B Stimson <dale.b.stimson@intel.com>
Signed-off-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NRiana Tauro <riana.tauro@intel.com>
Signed-off-by: NBadal Nilawar <badal.nilawar@intel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: NAndi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013154526.2105579-2-ashutosh.dixit@intel.com

On some platforms we potentially have different alignment restrictions
depending on the memory type. We also now have different alignment
restrictions for the same region across different kernel versions.
Extend the region query to return the minimum required GTT alignment.

Testcase: igt@gem_create@create-ext-placement-alignment
Testcase: igt@i915_query@query-regions-sanity-check
Suggested-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Cc: Michal Mrozek <michal.mrozek@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Stuart Summers <stuart.summers@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Yang A Shi <yang.a.shi@intel.com>
Cc: Nirmoy Das <nirmoy.das@intel.com>
Cc: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Reviewed-by: NNirmoy Das <nirmoy.das@intel.com>
Acked-by: NJordan Justen <jordan.l.justen@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221004114915.221708-2-matthew.auld@intel.com

It turns out that on production DG2/ATS HW we should have support for
PS64. This feature allows to provide a 64K TLB hint at the PTE level,
which is a lot more flexible than the current method of enabling 64K GTT
pages for the entire page-table, since that leads to all kinds of
annoying restrictions, as documented in:

commit caa574ff
Author: Matthew Auld <matthew.auld@intel.com>
Date:   Sat Feb 19 00:17:49 2022 +0530

    drm/i915/uapi: document behaviour for DG2 64K support

    On discrete platforms like DG2, we need to support a minimum page size
    of 64K when dealing with device local-memory. This is quite tricky for
    various reasons, so try to document the new implicit uapi for this.

With PS64, we can now drop the 2M GTT alignment restriction, and instead
only require 64K or larger when dealing with lmem. We still use the
compact-pt layout when possible, but only when we are certain that this
doesn't interfere with userspace.

Note that this is a change in uAPI behaviour, but hopefully shouldn't be
a concern (IGT is at least able to autodetect the alignment), since we
are only making the GTT alignment constraint less restrictive.

Based on a patch from CQ Tang.

v2: update the comment wrt scratch page
v3: (Nirmoy)
 - Fix the selftest to actually use the random size, plus some comment
   improvements, also drop the rem stuff.
Reported-by: NMichal Mrozek <michal.mrozek@intel.com>
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Stuart Summers <stuart.summers@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Yang A Shi <yang.a.shi@intel.com>
Cc: Nirmoy Das <nirmoy.das@intel.com>
Cc: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Reviewed-by: NNirmoy Das <nirmoy.das@intel.com>
Acked-by: NMichal Mrozek <michal.mrozek@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221004114915.221708-1-matthew.auld@intel.com

Commit 3e7abf81 ("drm/i915: Extract GT render power state management")
removes the "trace_intel_gpu_freq_change()" trace points but
their definition was left without users. Remove it.
Suggested-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NAndi Shyti <andi.shyti@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221011135940.367048-1-andi.shyti@linux.intel.com

Commit 39a2bd34 ("drm/i915: Use the vma resource as argument for gtt
binding / unbinding") introduced a regression that due to the vma resource
tracking of the binding state, dpt ptes were not correctly repopulated.
Fix this by clearing the vma resource state before repopulating.
The state will subsequently be restored by the bind_vma operation.

Fixes: 39a2bd34 ("drm/i915: Use the vma resource as argument for gtt binding / unbinding")
Signed-off-by: NThomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912121957.31310-1-thomas.hellstrom@linux.intel.com
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.18+
Reported-and-tested-by: NKevin Boulain <kevinboulain@gmail.com>
Tested-by: NDavid de Sousa <davidesousa@gmail.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Reviewed-by: NAndrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221005121159.340245-1-thomas.hellstrom@linux.intel.com

Read the values stored in the SLPC structures. Remove the
fields that are no longer valid (like RPS interrupts) as
well.

v2: Move all functionality changes to this patch (Jani)
v3: Fix compile warning and if condition (Jani)
Signed-off-by: NVinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221005155943.34747-3-vinay.belgaumkar@intel.com

Move it to the RPS source file.

v2: Separate out code movement and functional changes (Jani)
Signed-off-by: NVinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221005155943.34747-2-vinay.belgaumkar@intel.com

The assignment to variable taken is redundant and so it can be
removed as well as the variable too.

Cleans up clang-scan build warnings:
warning: Although the value stored to 'taken' is used in the enclosing
expression, the value is never actually read from 'taken'
[deadcode.DeadStores]
Signed-off-by: NColin Ian King <colin.i.king@gmail.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221007195345.2749911-1-colin.i.king@gmail.com

The variable ret is being assigned with a value that is never read
both before and after a while-loop. The variable is being re-assigned
inside the while-loop and afterwards on the call to the function
i915_gem_object_lock_interruptible. Remove the redundants assignments.

Cleans up clang scan-build warnings:

warning: Although the value stored to 'ret' is used in the
enclosing expression, the value is never actually read
from 'ret' [deadcode.DeadStores]

warning: Value stored to 'ret' is never read [deadcode.DeadStores]
Signed-off-by: NColin Ian King <colin.i.king@gmail.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221007194745.2749277-1-colin.i.king@gmail.com

Restore the previous behaviour here where we compare the
pci_resource_len() with the actual lmem_size, and not the dsm size,
since dsm here is just some subset snipped off the end of the lmem.
Otherwise we will incorrectly report an io_size > 0 on small-bar
systems.

It doesn't looks like MTL is expecting small-bar with its stolen memory,
based on:

  GEM_BUG_ON(pci_resource_len(pdev, GEN12_LMEM_BAR) != SZ_256M)
  GEM_BUG_ON((dsm_size + SZ_8M) > lmem_size)

So just move the HAS_BAR2_SMEM_STOLEN() check first, which then ignores
the small bar part, and we can go back to checking lmem_size against the
BAR size.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7007
Fixes: dbb2ffbf ("drm/i915/mtl: enable local stolen memory")
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Cc: Aravind Iddamsetty <aravind.iddamsetty@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221005153148.758822-2-matthew.auld@intel.com