The previous AES-NI CTR optimization compiling failure gas 2.16.1 fix
introduces another compiling failure by itself. This patch fixes that.
Reported-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Andrew Morton reported that AES-NI CTR optimization failed to compile
with gas 2.16.1, the error message is as follow:

arch/x86/crypto/aesni-intel_asm.S: Assembler messages:
arch/x86/crypto/aesni-intel_asm.S:752: Error: suffix or operands invalid for `movq'
arch/x86/crypto/aesni-intel_asm.S:753: Error: suffix or operands invalid for `movq'

To fix this, a gas macro is defined to assemble movq with 64bit
general purpose registers and XMM registers. The macro will generate
the raw .byte sequence for needed instructions.
Reported-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

To take advantage of the hardware pipeline implementation of AES-NI
instructions. CTR mode cryption is implemented in ASM to schedule
multiple AES-NI instructions one after another. This way, some latency
of AES-NI instruction can be eliminated.

Performance testing based on dm-crypt should 50% reduction of
ecryption/decryption time.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

->kill_sb() will be called after any failure exit, so no need
to duplicate what it can do.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

... instead of mixing FMODE_ and O_
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

If we do something like try to print to the OF console from an NMI
while we're already in OpenFirmware, we'll deadlock on the spinlock.

Use a raw spinlock and disable NMIs when we take it.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

People should be using the perf events interfaces, and
the way these system call facilities used the %pcr conflicts
with the usage of the NMI watchdog and perf events.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding vbus_pin_inverted so that the usb detect pin can be active high
or low depending on HW implementation also replaced the
gpio_get_value(udc->vbus_pin); with a call to vbus_is_present(udc); This
allows the driver to be loaded and save about 0,15W on the consumption.
Signed-off-by: NEirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

trivial patch enabling g_nokia on rx51_defconfig.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Also fixes tab/space issue causing checkpatch to complain.
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This centralize some spread-out initialization of descriptors into
one function and cleans up the error paths.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The DM365 Spectrum Digital EVM comes with an EEPROM
connected to SPI0.
This patch adds support for the SPI EEPROM.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds SPI init for DM365.
It does the following
1) Initializes SPI0
2) Defines resources to be used by SPI0
3) Adds platform data for SPI0
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch does the following

1) Minor change to the SPI clocks making it
similar to DM365.
2) Changing the interrupt used by SPI0
3) Adding EDMA resources that can be used by SPI0
4) Adding platform specific data.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds "spi.h" header file that will be used by board and
architecture specific code.
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Remove unneeded 'struct davinci_clk' wrapper around 'struct
clk_lookup' and use clk_lookup directly.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Just faults right now, will add other traps later.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we reach the loop, len is at least 1, we only stay in the loop when
len is at least MAX_BYTE_COUNT + 1, MAX_BYTE_COUNT is subtracted in each
iteration. So when we leave the loop, or didn't take it, len is at least 1.
Testing whether len is non-zero appears redundant.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Replace open-coded rate limiting logic with __ratelimit().
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Iranna D Ankad reported that IBM x3950 systems have boot
problems after this commit:

 |
 | commit b9c61b70
 |
 |    x86/pci: update pirq_enable_irq() to setup io apic routing
 |

The problem is that with the patch, the machine freezes when
console=ttyS0,... kernel serial parameter is passed.

It seem to freeze at DVD initialization and the whole problem
seem to be DVD/pata related, but somehow exposed through the
serial parameter.

Such apic problems can expose really weird behavior:

  ACPI: IOAPIC (id[0x10] address[0xfecff000] gsi_base[0])
  IOAPIC[0]: apic_id 16, version 0, address 0xfecff000, GSI 0-2
  ACPI: IOAPIC (id[0x0f] address[0xfec00000] gsi_base[3])
  IOAPIC[1]: apic_id 15, version 0, address 0xfec00000, GSI 3-38
  ACPI: IOAPIC (id[0x0e] address[0xfec01000] gsi_base[39])
  IOAPIC[2]: apic_id 14, version 0, address 0xfec01000, GSI 39-74
  ACPI: INT_SRC_OVR (bus 0 bus_irq 1 global_irq 4 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 5 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 3 global_irq 6 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 4 global_irq 7 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 6 global_irq 9 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 7 global_irq 10 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 8 global_irq 11 low edge)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 12 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 12 global_irq 15 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 13 global_irq 16 dfl dfl)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 17 low edge)
  ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 18 dfl dfl)

It turns out that the system has three io apic controllers, but
boot ioapic routing is in the second one, and that gsi_base is
not 0 - it is using a bunch of INT_SRC_OVR...

So these recent changes:

 1. one set routing for first io apic controller
 2. assume irq = gsi

... will break that system.

So try to remap those gsis, need to seperate boot_ioapic_idx
detection out of enable_IO_APIC() and call them early.

So introduce boot_ioapic_idx, and remap_ioapic_gsi()...

 -v2: shift gsi with delta instead of gsi_base of boot_ioapic_idx

 -v3: double check with find_isa_irq_apic(0, mp_INT) to get right
      boot_ioapic_idx

 -v4: nr_legacy_irqs

 -v5: add print out for boot_ioapic_idx, and also make it could be
      applied for current kernel and previous kernel

 -v6: add bus_irq, in acpi_sci_ioapic_setup, so can get overwride
      for sci right mapping...

 -v7: looks like pnpacpi get irq instead of gsi, so need to revert
      them back...

 -v8: split into two patches

 -v9: according to Eric, use fixed 16 for shifting instead of remap

 -v10: still need to touch rsparser.c

 -v11: just revert back to way Eric suggest...
      anyway the ioapic in first ioapic is blocked by second...

 -v12: two patches, this one will add more loop but check apic_id and irq > 16
Reported-by: NIranna D Ankad <iranna.ankad@in.ibm.com>
Bisected-by: NIranna D Ankad <iranna.ankad@in.ibm.com>
Tested-by: NGary Hade <garyhade@us.ibm.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: len.brown@intel.com
LKML-Reference: <4B8A321A.1000008@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Now that both Xen and VMI disable allocations of PTE pages from high
memory this paravirt op serves no further purpose.

This effectively reverts ce6234b5 "add kmap_atomic_pte for mapping
highpte pages".
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
LKML-Reference: <1267204562-11844-3-git-send-email-ian.campbell@citrix.com>
Acked-by: NAlok Kataria <akataria@vmware.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Preventing HIGHPTE allocations under VMI will allow us to remove the
kmap_atomic_pte paravirt op.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
LKML-Reference: <1267204562-11844-2-git-send-email-ian.campbell@citrix.com>
Acked-by: NAlok Kataria <akataria@vmware.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

There's a path in the pagefault code where the kernel deliberately
breaks its own locking rules by kmapping a high pte page without
holding the pagetable lock (in at least page_check_address). This
breaks Xen's ability to track the pinned/unpinned state of the
page. There does not appear to be a viable workaround for this
behaviour so simply disable HIGHPTE for all Xen guests.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
LKML-Reference: <1267204562-11844-1-git-send-email-ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pasi Kärkkäinen <pasik@iki.fi>
Cc: <stable@kernel.org> # .32.x: 14315592: Allow highmem user page tables to be disabled at boot time
Cc: <stable@kernel.org> # .32.x
Cc: <xen-devel@lists.xensource.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

The following patch defines sigcontext ABI of ColdFire.  Due to ISA
restrictions ColdFire needs different rt_sigreturn trampoline.

And due to ColdFire FP registers being 8-bytes instead of 12-bytes on
m68k, sigcontext and fpregset structures should be updated.

Regarding the sc_fpstate[16+6*8] field, it would've been enough 16
bytes to store ColdFire's FP state.  To accomodate GLIBC's libSegFault
it would'be been enough 6*8 bytes (room for the 6 non-call-clobbered
FP registers).  I set it to 16+6*8 to provide some extra space for any
future changes in the ColdFire FPU.
Signed-off-by: NMaxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Port syscalls for NPTL support to m68knommu.
Signed-off-by: NMaxim Kuvyrkov <maxim@codesourcery.com>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

This patch adds several syscalls, that provide necessary
functionality to support NPTL on m68k/ColdFire.
The syscalls are get_thread_area, set_thread_area, atomic_cmpxchg_32 and
atomic_barrier.
The cmpxchg syscall is required for ColdFire as it doesn't support 'cas'
instruction.

Also a ptrace call PTRACE_GET_THREAD_AREA is added to allow debugger to
inspect the TLS storage.
Signed-off-by: NMaxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

"pgdat" is unused, so we can eliminate it and turn page_to_phys()
into a single-line macro.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

This patch switches m68k to generic siginfo layout.  The custom layout
of m68k's `struct siginfo' had several issues due to not considering
aliasing of members in the union, e.g., _uid32 was at different offsets
in ._kill, ._rt and ._sigchld.
Signed-off-by: NMaxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

The valkyriefb driver needs the CUDA to work in order to set the video
mode at boot. So initialise the device earlier, and bring the m68k code
closer to the powermac code.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Move platform device code from the drivers to the platform init function.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Move platform device code from the driver to the platform init function.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Remove the old 68k Mac serial port code and a lot of related cruft. Add
new SCC platform devices to mac 68k platform.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Adjust the platform device code to conform with the code style used in the
rest of this patch series. No need to name resources nor to register
devices which are not applicable.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Cleanup whitespace and comments. Remove some dead code.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

@depends on haskernel@
expression x,__divisor;
@@

- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>