it87: Add support for the IT8718F

The IT8718F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8716F, so adding support to the
it87 driver was pretty straightforward. The most significant difference
is that the IT8718F has up to 8 VID pins, instead of 6 for the older
chips.

For the IT8718F, the VID value can only be read from Super-I/O space.

Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

it87: Add support for the IT8716F

The IT8716F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8712F, so adding support to the
it87 driver was pretty straightforward. The most significant change here
is that the IT8716F has 16-bit fan speed counters, so the user no more
needs to tweak the fan clock dividers to get the best readings.

Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)

Thanks to Stian Oksavik, Olivier Nicolas, Prakash Punnoor and
Juergen Kilb for testing the early versions of this patch.

Thanks also to ITE for providing datasheets and answering my questions.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add documentation for the w83627ehf hardware monitoring driver.
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".

The usbmon splits such cases already thanks to its timestamp, but
it's not always available.

I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for Ontrak ADU USB devices.

Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NSteven Haigh <netwiz@crc.id.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add driver for AIRcable USB Bluetooth dongle.
Signed-off-by: NNaranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A little more detail on how and when to poll() /proc/bus/usb/devices.
Signed-off-by: NSam Bishop <sam@bishop.dhs.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Grammar, spelling, and stylistic edits.
Signed-off-by: NSam Bishop <sam@bishop.dhs.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Resetting the devices during driver initialization can be a costly
operation in terms of time (especially scsi devices).  This option can be
used by drivers to know that user forcibly wants the devices to be reset
during initialization.

This option can be useful while kernel is booting in unreliable
environment.  For ex.  during kdump boot where devices are in unknown
random state and BIOS execution has been skipped.
Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make futexes work under NOMMU conditions.

This can be tested by running this in one shell:

	#define SYSERROR(X, Y) \
		do { if ((long)(X) == -1L) { perror(Y); exit(1); }} while(0)

	int main()
	{
		int shmid, tmp, *f, n;

		shmid = shmget(23, 4, IPC_CREAT|0666);
		SYSERROR(shmid, "shmget");

		f = shmat(shmid, NULL, 0);
		SYSERROR(f, "shmat");

		n = *f;
		printf("WAIT: %p{%x}\n", f, n);
		tmp = futex(f, FUTEX_WAIT, n, NULL, NULL, 0);
		SYSERROR(tmp, "futex");
		printf("WAITED: %d\n", tmp);

		tmp = shmdt(f);
		SYSERROR(tmp, "shmdt");

		exit(0);
	}

And then this in the other shell:

	#define SYSERROR(X, Y) \
		do { if ((long)(X) == -1L) { perror(Y); exit(1); }} while(0)

	int main()
	{
		int shmid, tmp, *f;

		shmid = shmget(23, 4, IPC_CREAT|0666);
		SYSERROR(shmid, "shmget");

		f = shmat(shmid, NULL, 0);
		SYSERROR(f, "shmat");

		(*f)++;
		printf("WAKE: %p{%x}\n", f, *f);
		tmp = futex(f, FUTEX_WAKE, 1, NULL, NULL, 0);
		SYSERROR(tmp, "futex");
		printf("WOKE: %d\n", tmp);

		tmp = shmdt(f);
		SYSERROR(tmp, "shmdt");

		exit(0);
	}

The first program will set up a SYSV IPC SHM segment and wait on a futex in it
for the number at the start to change.  The program will increment that number
and wake the first program up.  This leads to output of the form:

	SHELL 1			SHELL 2
	=======================	=======================
	# /dowait
	WAIT: 0xc32ac000{0}
				# /dowake
				WAKE: 0xc32ac000{1}
	WAITED: 0		WOKE: 1
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add documentation about using shared memory in NOMMU mode.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make mremap() partially work for NOMMU kernels.  It may resize a VMA provided
that it doesn't exceed the size of the slab object in which the storage is
allocated that the VMA refers to.  Shareable VMAs may not be resized.

Moving VMAs (as permitted by MREMAP_MAYMOVE) is not currently supported.

This patch also makes use of the fact that the VMA list is now ordered to cut
it short when possible.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Implement /proc/pid/maps for NOMMU by reading the vm_area_list attached to
current->mm->context.vmlist.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This fell behind a bit, get it updated so the documentation
has something in common with reality.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Initial register bank cleanup. Make SR.RB configurable, and add some
preliminary documentation on register bank usage within the kernel.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

PCI-Express AER (Advanced Error Reporting) provides more robust error reporting.
The series of patches enable kernel support to AER.

The initial patches were written by Tom Long Nguyen. I ported them to the kernel
2.6.18-rc3. Many thanks to Rajesh Shah and Narayanan Chandramouli for their great
review comments and testing help.

Patch 1 consists of the pciaer-howto.txt document.
Signed-off-by: NZhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c-viapro: Add support for the VT8237A and VT8251

Documentation update included. Compile tested.
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c-stub: Chip address as a module parameter

Add a mandatory chip_addr parameter to i2c-stub. This parameter
defines to which chip address the driver will respond, instead of
reponding to all addresses as before. The idea is to prevent the
users from loading i2c-stub at random and being then confused by
the results of sensors-detect or other user-space tools.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c: Plan i2c-isa for removal

i2c-isa doesn't make much sense in the device driver model. Drivers
relying on it are better implemented as platform drivers. We must
wait for recent versions of libsensors (2.10.0 or later) to be widely
deployed beforehand, though. This move should also make it easier to
convert i2c-core to the device driver model.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add the pm_trace attribute in /sys/power which has to be explicitly set to
one to really enable the "PM tracing" code compiled in when CONFIG_PM_TRACE
is set (which modifies the machine's CMOS clock in unpredictable ways).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a boot parameter to reserve high linear address space for hypervisors.
This is necessary to allow dynamically loaded hypervisor modules, which might
not happen until userspace is already running, and also provides a useful tool
to benchmark the performance impact of reduced lowmem address space.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently one can enable slab reclaim by setting an explicit option in
/proc/sys/vm/zone_reclaim_mode.  Slab reclaim is then used as a final
option if the freeing of unmapped file backed pages is not enough to free
enough pages to allow a local allocation.

However, that means that the slab can grow excessively and that most memory
of a node may be used by slabs.  We have had a case where a machine with
46GB of memory was using 40-42GB for slab.  Zone reclaim was effective in
dealing with pagecache pages.  However, slab reclaim was only done during
global reclaim (which is a bit rare on NUMA systems).

This patch implements slab reclaim during zone reclaim.  Zone reclaim
occurs if there is a danger of an off node allocation.  At that point we

1. Shrink the per node page cache if the number of pagecache
   pages is more than min_unmapped_ratio percent of pages in a zone.

2. Shrink the slab cache if the number of the nodes reclaimable slab pages
   (patch depends on earlier one that implements that counter)
   are more than min_slab_ratio (a new /proc/sys/vm tunable).

The shrinking of the slab cache is a bit problematic since it is not node
specific.  So we simply calculate what point in the slab we want to reach
(current per node slab use minus the number of pages that neeed to be
allocated) and then repeately run the global reclaim until that is
unsuccessful or we have reached the limit.  I hope we will have zone based
slab reclaim at some point which will make that easier.

The default for the min_slab_ratio is 5%

Also remove the slab option from /proc/sys/vm/zone_reclaim_mode.

[akpm@osdl.org: cleanups]
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some buggy systems can machine check when config space accesses
happen for some non existent devices.  i386/x86-64 do some early
device scans that might trigger this. Allow pci=noearly to disable
this. Also when type 1 is disabling also don't do any early
accesses which are always type1.

This moves the pci= configuration parsing to be a early parameter.
I don't think this can break anything because it only changes
a single global that is only used by PCI.

Cc: gregkh@suse.de
Cc: Trammell Hudson <hudson@osresearch.net>
Signed-off-by: NAndi Kleen <ak@suse.de>

Signed-off-by: NAndi Kleen <ak@suse.de>

Describes the stack organization on x86-64.

I changed it a bit and removed some obsolete information and the
questions.

Cc: kaos@sgi.com
Signed-off-by: NAndi Kleen <ak@suse.de>

... instead of using a CONFIG option. The config option still controls
if the resulting executable actually has unwind information.

This is useful to prevent compilation errors when users select
CONFIG_STACK_UNWIND on old binutils and also allows to use
CFI in the future for non kernel debugging applications.

Cc: jbeulich@novell.com
Cc: sam@ravnborg.org
Signed-off-by: NAndi Kleen <ak@suse.de>

Signed-off-by: NAndi Kleen <ak@suse.de>

Adds a new /proc/sys/kernel/nmi_watchdog call that will enable/disable the
nmi watchdog.

By entering a non-zero value here, a user can enable the nmi watchdog to
monitor the online cpus in the system.  By entering a zero value here, a
user can disable the nmi watchdog and free up a performance counter which
could then be utilized by the oprofile subsystem, otherwise oprofile may be
short a counter when in use.
Signed-off-by: NDon Zickus <dzickus@redhat.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

The file sysfs-power that documents the interface in the /sys/power/ directory
is added to Documentation/ABI/testing.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This lists the /sys/devices/.../power/state file, and its internal support,
as due for removal next year.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This turned into a rewrite of Documentation/power/devices.txt:

 - Provide more of the "big picture"

 - Fixup some of the horribly ancient/obsolete description of device suspend()
   semantics; lots of text just got deleted.

 - Add a decent description of PM_EVENT_* codes, including the new PRETHAW code
   needed in some swsusp scenarios.

 - Describe the new PM factorization from Linus:
     * class suspend, current suspend, then suspend_late
     * NOT suspend_prepare, it wasn't really usable
     * resume_early, current resume, class resume.

 - Updates power/state docs to be correct, and deprecate its usage except for
   driver testing.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

deprecate PHYSDEV* values in the uevent environment

These values are no longer needed and inconsistent with the
stacking of class devices. The event environment should not
carry properties of a parent device. The key PHYSDEVDRIVER is
available as DRIVER, PHYDEVBUS is indentical SUBSYSTEM. Class
devices should not carry any of these values.
Signed-off-by: NKay Sievers <kay.sievers@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJens M. Noedler <noedler@web.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

	Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.

	The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add auto-generated utsrelease.h to dontdiff file.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

I noticed a few typos while reading makefiles.txt to learn about the
kbuild system.  Attached is a patch against 2.6.18 to fix them.
Remove trailing whitespace while we are there..
Signed-off-by: NBryce Harrington <bryce@osdl.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Clarify the use of "make C=" in the top-level Makefile, and fix a
typo in the Documentation file.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>